Physics / Fizik
Permanent URI for this collectionhttps://hdl.handle.net/11147/6
Browse
10 results
Search Results
Article Citation - WoS: 4Citation - Scopus: 5Enhanced Optoelectronic Properties of Magnetron Sputtered Ito/Ag Multilayers by Electro-Annealing(AVS, 2022) Uyanık, Zemzem; Türkoğlu, Fulya; Köseoğlu, Hasan; Ekmekçioğlu, Merve; Ata, Bengü; Demirhan, Yasemin; Özdemir, Mehtap; Aygün, Gülnur; Özyüzer, LütfiIndium tin oxide/silver/indium tin oxide (ITO/Ag/ITO) multilayers have attracted much attention to fulfill the growing need for high-performance transparent conducting oxide electrodes. To make these transparent multilayers work better, electro-annealing, which is a method of self-heating by electric current, can be effective. Moreover, the effect of current on ITO/Ag/ITO multilayers should be investigated to make sure that electronic devices will be reliable over their lifetime. In this study, ITO/Ag/ITO multilayer electrodes with varying Ag thicknesses were grown by DC magnetron sputtering at room temperature. Structural, optical, and electrical properties of these multilayers were investigated before and after electro-annealing. Measurement results revealed that improved optical transmittance and sheet resistance can be obtained by the optimization of Ag thickness for the as-grown ITO/Ag/ITO layers. The highest figure of merit (FoM) value of 17.37 × 10−3 Ω−1 with optical transmittance of 85.15% in the visible region and sheet resistance of 11.54 Ω/□ was obtained for the Ag thickness of 16.5 nm for as-grown samples. The electro-annealing of as-grown ITO/Ag/ITO multilayers led to improved optical behavior of the multilayer structure over a wide spectral range, especially in the near-infrared range. Electro-annealing also provided an improvement in the crystallinity and sheet resistance of the electrodes. The improvement of the electrical and optical properties of the structure enabled a FoM of 23.07 × 10−3 Ω−1 with the optical transmittance of 86.80% in the visible region and sheet resistance of 10.52 Ω/□. The findings of this work provide proper knowledge of the properties of ITO/Ag/ITO multilayers under electrical current and suggest that the overall performance of the multilayers can be improved by the electro-annealing process.Article Citation - WoS: 33Citation - Scopus: 39High Transparent, Low Surface Resistance Zto/Ag Multilayer Thin Film Electrodes on Glass and Polymer Substrates(Pergamon-Elsevier Science Ltd, 2021) Ekmekçioğlu, Merve; Erdoğan, Nursev; Astarlıoğlu, Aziz Taner; Yiğen, Serap; Aygün, Gülnur; Özyüzer, Lütfi; Özdemir, MehtapZinc tin oxide (ZTO)/Ag/ZTO multilayer thin films were grown by direct current (DC) magnetron sputtering technique at room temperature on soda lime glass (SLG) and different polymer substrates such as polycarbonate (PC) and polyethylene terephthalate (PET) for transparent conductive electrode (TCE) applications. The effect of substrate on the structural, optical and electrical characteristics of ZTO/Ag/ZTO multilayers was investigated. All prepared ZTO/Ag/ZTO films presented amorphous structure as expected from room temperature deposition process and smooth surface quality with very low surface roughness. We found that ZTO/Ag/ZTO multilayer films grown on SLG, PET and PC substrates have very high optical transmission and low surface resistance. Moreover, after ZTO/Ag/ZTO multilayer thin film deposition on polymer substrates, the optical transmission was found to be enhanced because the higher absorption due to Ag layer is compensated by lower reflectance. Our results suggest that ZTO/Ag/ZTO multilayer thin films on any substrate can be a promising alternative to indium tin oxide (ITO) films as a cost-effective, indium-free, flexible and transparent electrode for various applications.Article Citation - WoS: 6Citation - Scopus: 6Nanolitography Based on Electrospun and Etched Nanofibers(Elsevier, 2021) Noori, Aileen; Döğer, Hilal; Demirhan, Yasemin; Özdemir, Mehtap; Özyüzer, Lütfi; Aygün, Gülnur; Sağlam, ÖzgeIn this study, we propose a new type of nanolithography procedure to fabricate orderly patterned metallic nanostructures using the electrohydrodynamic method and the reactive ion etching process. The electrohydrodynamic process parameters were tuned so as to create patterning with precision, and fibers in nanoscale on silver-coated substrates. We also studied reactive ion etching with different durations on the well-patterned samples. The experiments show that applying a voltage of 400 V resulted in straight patterned fibers with a diameter of 208.7 ? 30.3 nm. The statistical analysis on scanning electron microscope (SEM) images showed a significant difference in the diameter of the fibers fabricated at 400 V compared to those at 500 V and 600 V. We also confirm that the etching process has no affect on the fiber diameter. Moreover, electron dispersive X-Ray spectrometer (EDX) results suggest that an etching duration of 7 min is sufficient to remove the silver coating that is not covered with the fibers, and protect the silver nanostructures underneath the fibers. Utilizing a lowcost nanolithography procedure, we obtain the orderly patterned silver nanostructures for possible integration into miniaturized devices.Article Citation - WoS: 20Citation - Scopus: 23Surface Free Energy and Wettability Properties of Transparent Conducting Oxide-Based Films With Ag Interlayer(Elsevier, 2021) Özbay, Salih; Erdoğan, Nursev; Erden, Fuat; Ekmekçioğlu, Merve; Rakop, Büşra; Özdemir, Mehtap; Aygün, Gülnur; Özyüzer, LütfiITO, ZTO, AZO and Ag are commonly used in transparent conducting oxide (TCO)/metal/TCO electrodes to form multilayered thin films on a suitable substrate. A detailed surface free energy (SFE) knowledge of these films is critical to design desirable TCO-based sandwich structures. In this study, TCO/Ag/TCO multilayer thin films were coated onto glass substrates using ITO, ZTO, AZO and Ag targets by magnetron sputtering. The wettability properties of TCO, Ag interlayer and TCO/Ag/TCO were evaluated by contact angle measurements of seven different liquids having various surface tension values. The dispersive and polar components of SFE were calculated using geometric and harmonic mean approaches. The acidic and basic components of SFE were calculated using van Oss-Chaudhury-Good method. Following this, the work of adhesion values between TCO films and Ag interlayer were estimated using SFE values of the films. The results show that the SFE components of the surfaces differ depending on the TCO type, the total SFE values of TCO/Ag/TCO films were lower than that of TCO films, and AZO/Ag adhesion is stronger than the other TCO/Ag structures. The reasons behind these differences were discussed by evaluating the SFE, XRD, AFM and SEM analysis simultaneously.Article Citation - WoS: 2Citation - Scopus: 2In-Situ Thin Film Copper-Copper Thermocompression Bonding for Quantum Cascade Lasers(Springer, 2021) Rouhi, Sina; Özdemir, Mehtap; Ekmekçioğlu, Merve; Yiğen, Serap; Demirhan, Yasemin; Szerling, Anna; Kosiel, Kamil; Kozubal, Maciej; Kruszka, Renata; Prokaryn, Piotr; Ertuğrul, Mehmet; Reno, John L.; Aygün, Gülnur; Özyüzer, LütfiThe choice of metals, bonding conditions and interface purity are critical parameters for the performance of metal-metal bonding quality for quantum cascade lasers (QCLs). Here, we present a novel approach for the thermocompression bonding of Cu-Cu thin films on GaAs-based waveguides without having any oxide phase, contamination or impurities at the interface. We designed a hybrid system in which magnetron sputtering of Ta, thermal evaporation of Cu and Cu-Cu thermocompression bonding processes can be performed sequentially under high vacuum conditions. GaAs/Ta/Cu and Cu/Ta/GaAs structures were thermocompressionally bonded in our in-situ homebuilt bonding system by optimizing the deposition parameters and bonding conditions. The grown thin film and the obtained interfaces were characterized using x-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive x-ray spectroscopy (EDX) techniques. The optimum Ta and Cu films' thicknesses were found to be about 20 nm and 500 nm, respectively. EDX analysis showed that the Ta thin film interlayer diffused into the Cu structure, providing better adhesivity and rigidity for the bonding. Additionally, no oxidation phases were detected at the interface. The best bonding quality was obtained when heated up to 430 degrees C with an applied pressure of 40 MPa during bonding process.Article Citation - WoS: 3Citation - Scopus: 3Compact Multilayer Thin-Film Color Filters and Direct Integration on White-Light Diodes for Color Conversion(Optical Society of America, 2021) Yiğen, Serap; Ekmekçioğlu, Merve; Özdemir, Mehtap; Aygün, Gülnur; Özyüzer, LütfiWe present highly efficient green, yellow, and red filters based on a metal-dielectric structure. The filters encompass only five layers of alternating zinc tin oxide and silver thin films that are grown on soda lime glass and white light-emitting diodes (LEDs) using direct current magnetron sputtering at room temperature. The designed filters provide efficient color filtering in the visible spectrum. High purity colored light is obtained by direct application of filters on LEDs as color converters. The presented method offers an easy way for realizing different colors by tuning the thicknesses of layers in the structure. (C) 2021 Optical Society of AmericaArticle Citation - WoS: 39Citation - Scopus: 46Surface Free Energy Analysis of Ito/Au Multilayer Thin Films on Polycarbonate Substrate by Apparent Contact Angle Measurements(Elsevier, 2020) Özbay, Salih; Erdoğan, Nursev; Erden, Fuat; Ekmekçioğlu, Merve; Özdemir, Mehtap; Aygün, Gülnur; Özyüzer, LütfiA detailed surface free energy (SFE) knowledge of transparent conducing oxide (TCO)/metal/TCO electrodes is necessary for their applications related to surface wettability. However, SFE analysis of these surfaces has not been performed systematically previously. In this study, ITO and ITO/Au/ITO multilayer thin films were coated onto O-2 plasma treated polycarbonate (PC) substrates by magnetron sputtering. The wettability characteristics of untreated PC, O-2 plasma treated PC, ITO, Au interlayer, and ITO/Au/ITO multilayer thin films were evaluated by apparent contact angle measurements of nine different test liquids having various surface tensions. Following this, Lifshitz-van der Waals, acidic, basic, dispersive, and polar components of SFE were calculated using acidbase, geometric and harmonic mean approaches. In the present study, in which the significance of calculation methods and selected liquid pairs on SFE parameters were investigated, the effect of Au interlayer presence on SFE parameters were also evaluated simultaneously. The results showed that the total SFE values of ITO/Au/ITO multilayer thin films were found to be higher than that of ITO surface. The reasons behind this difference were discussed in terms of SFE components obtained using various liquid pairs by different methods. The results were also supported with XRD, XPS, AFM, and TEM analysis.Article Citation - WoS: 31Citation - Scopus: 33The Controllable Deposition of Large Area Roll-To Sputtered Ito Thin Films for Photovoltaic Applications(Elsevier, 2020) Demirhan, Yasemin; Köseoğlu, Hasan; Türkoğlu, Fulya; Uyanık, Zemzem; Özdemir, Mehtap; Aygün, Gülnur; Özyüzer, LütfiIn the present study, using a large area roll-to-roll DC magnetron sputtering system deposition of ITO thin films on polyethylene terephthalate (PET) substrates were achieved. In order to investigate the effect of growth conditions on the film properties all through the deposition process, optical emission spectroscopy (OES) analysis have been accomplished in a governable way. The consequences of Oxygen partial pressure and film thickness on electrical, and optical properties of the films were determined. It was shown that the intensity of optical emission peaks are subjected to the discharge power and as well as the O-2/Ar flow ratio. Large area, uniform ITO films with relatively high transparency and low electrical resistivity (R(2)(<)50 Omega/sqr) were succesfully deposited on PET substrates. The significance of both the figure of merit (FOM) and the optical band gap values on the performance of different TCO thin films were addressed. In this work, the obtained results suggest that the overall performance is sufficient to implement the ITO films in photovoltaic and OLED applications. (C) 2019 Elsevier Ltd. All rights reserved.Article Citation - WoS: 63Citation - Scopus: 72Ito/Au Multilayer Thin Films on Transparent Polycarbonate With Enhanced Emi Shielding Properties(Elsevier, 2020) Erdoğan, Nursev; Erden, Fuat; Astarlıoğlu, A. Taner; Özdemir, Mehtap; Özbay, Salih; Aygün, Gülnur; Özyüzer, LütfiITO/Au/ITO multilayer thin films were deposited onto polycarbonate substrate via magnetron sputtering technique without intentional heating. The deposition times of both ITO and Au layers were studied to optimize the overall transparency and conductivity. As-prepared thin films were characterized using X-ray diffraction analysis, secondary ion mass spectroscopy, scanning and transmission electron microscopy, atomic force microscopy and physical property measurement system. The optical measurement results revealed that the transmittance of the films were enhanced by increasing the gold deposition time up to 15 s. Beyond this point, further increasing the duration caused a decrease in optical transmittance. Upon optimization of the Au deposition time, the deposition duration of ITO layers was also studied to increase electromagnetic interference (EMI) shielding effectiveness (SE). Maximum EMI SE in this work was measured as 26.8 dB, yielding 99.8% power attenuation, which was verified by simulation results.Article Citation - WoS: 5Citation - Scopus: 6A Comprehensive Study of Molybdenum Boats Behavior During Service Life for Continuous Thermal Evaporation Technique, Used in Thin Film Technology(Elsevier, 2020) Rouhi, Sina; Martinez-Medina, Jose Enrique; Özdemir, Mehtap; Ertuğrul, Mehmet; Aygün, Gülnur; Özyüzer, LütfiThe aim of this study is to calculate the optimum lifetime of Molybdenum (Mo) thermal evaporation boats for Copper (Cu) filling in thin film technologies. Three types of Mo boats with thicknesses of 0.2, 0.3 and 0.5 mm were used during the experiments under the high vacuum condition about 6.0 x 10(-6) Torr. The behavior of each boat was investigated by focusing on the total amount of evaporation material, operational time and applied power. Prior to the deposition process, material was loaded on the evaporation boat by two methods. In the first method, Cu wire was cut into 1 cm long, then every boat was filled with this amount of Cu material. The second alternative feeding method is to use a wire-feeder step motor, which refills boat with Cu wire during evaporation process. The latter one is very useful for continuous deposition process since there is no need to break the vacuum state. In both methods, however, the number of failures during operations increases after a series of experiments have been taken place because of boat aging. The results of failures have been analyzed by various methods, and it has been observed that thinner boats showed better stability for long time operation by continuous feeding technique.