Physics / Fizik
Permanent URI for this collectionhttps://hdl.handle.net/11147/6
Browse
5 results
Search Results
Article Citation - WoS: 11Citation - Scopus: 13Effect of Cnt Incorporation on Pan/Ppy Nanofibers Synthesized by Electrospinning Method(TÜBİTAK, 2020) İnce Yardımcı, Atike; Tanoğlu, Metin; Yılmaz, Selahattin; Selamet, YusufIn this study, carbon nanotubes (CNTs) added polyacrylonitrile/polypyrrole (PAN/PPy) electrospun nanofibers were produced. Average diameters of the nanofibers were measured as 268 and 153 nm for 10 and 25 wt% of PPy contents, respectively. A relatively higher strain to failure values (23.3%) were observed for the low PPy content. When as-grown CNTs (1 and 4 wt%) were added into the PAN/PPy blends, disordered nanofibers were observed to form within the microstructure. To improve the interfacial properties of CNTs/PAN/PPy composites, CNTs were functionalized with H2SO4/HNO3/HCl solution. The functionalized CNTs were well dispersed within the nanofibers and aligned along the direction of nanofibers. Therefore, beads formation on nanofibers decreased. The impedance of the nanofibers was found to decrease with the PPy content and CNT addition. These nanofibers had a great potential to be used as an electrochemical actuator or a tissue engineering scaffold.Article Citation - WoS: 18Citation - Scopus: 17Cnt Incorporated Polyacrilonitrile/Polypyrrole Nanofibers as Keratinocytes Scaffold(Trans Tech Publications, 2019) İnce Yardımcı, Atike; Aypek, Hande; Öztürk, Özgür; Yılmaz, Selahattin; Özçivici, Engin; Meşe, Gülistan; Selamet, YusufPolypyrrole (PPy) is an attractive scaffold material for tissue engineering with its non-toxic and electrically conductive properties. There has not been enough information about PPy usage in skin tissue engineering. The aim of this study is to investigate biocompatibility of polyacrilonitrile (PAN)/PPy nanofibrous scaffold for human keratinocytes. PAN/PPy bicomponent nanofibers were prepared by electrospinning, in various PPy concentrations and with carbon nanotube (CNT) incorporation. The average diameter of electrospun nanofibers decreased with increasing PPy concentration. Further, agglomerated CNTs caused beads and disordered parts on the surface of nanofibers. Biocompatibility of these PAN/PPy and PAN/PPy/CNT scaffolds were analyzed in vitro. Both scaffolds provided adhesion and proliferation of keratinocytes. Nanofiber diameter did not significantly influence the morphology of cells. However, with increasing number of cells, cells stayed among nanofibers and this affected their shape and size. In this study, we demonstrated that PAN/PPy and PAN/PPy/CNT scaffolds enabled the growth of keratinocytes, showing their biocompatibility.Article Citation - WoS: 8Citation - Scopus: 10Experimental and Computational Investigation of Graphene/Sams Schottky Diodes(Elsevier Ltd., 2018) Aydın, Hasan; Bacaksız, Cihan; Yağmurcukardeş, Nesli; Karakaya, Caner; Mermer, Ömer; Can, Mustafa; Senger, Ramazan Tuğrul; Şahin, Hasan; Selamet, YusufWe have investigated the effect of two different self-assembled monolayers (SAMs) on electrical characteristics of bilayer graphene (BLG)/n-Si Schottky diodes. Novel 4″bis(diphenylamino)-1, 1′:3″-terphenyl-5′ carboxylic acids (TPA) and 4,4-di-9H-carbazol-9-yl-1,1′:3′1′-terphenyl-5′ carboxylic acid (CAR) aromatic SAMs have been used to modify n-Si surfaces. Cyclic voltammetry (CV) and Kelvin probe force microscopy (KPFM) results have been evaluated to verify the modification of n-Si surface. The current–voltage (I–V) characteristics of bare and SAMs modified devices show rectification behaviour verifying a Schottky junction at the interface. The ideality factors (n) from ln(I)–V dependences were determined as 2.13, 1.96 and 2.07 for BLG/n-Si, BLG/TPA/n-Si and BLG/CAR/n-Si Schottky diodes, respectively. In addition, Schottky barrier height (SBH) and series resistance (R s ) of SAMs modified diodes were decreased compared to bare diode due to the formation of a compatible interface between graphene and Si as well as π–π interaction between aromatic SAMs and graphene. The CAR-based device exhibits better diode characteristic compared to the TPA-based device. Computational simulations show that the BLG/CAR system exhibits smaller energy-level-differences than the BLG/TPA, which supports the experimental findings of a lower Schottky barrier and series resistance in BLG/CAR diode.Article Citation - WoS: 2Citation - Scopus: 2Surface Roughness Estimation of Mbe Grown Cdte/Gaas(211)b by Ex-Situ Spectroscopic Ellipsometry(American Institute of Physics, 2016) Karakaya, Merve; Bilgilisoy, Elif; Arı, Ozan; Selamet, YusufSpectroscopic ellipsometry (SE) ranging from 1.24 eV to 5.05 eV is used to obtain the film thickness and optical properties of high index (211) CdTe films. A three-layer optical model (oxide/CdTe/GaAs) was chosen for the ex-situ ellipsometric data analysis. Surface roughness cannot be determined by the optical model if oxide is included. We show that roughness can be accurately estimated, without any optical model, by utilizing the correlation between SE data (namely the imaginary part of the dielectric function, <ϵ2 > or phase angle, ψ) and atomic force microscopy (AFM) roughness. <ϵ2 > and ψ values at 3.31 eV, which corresponds to E1 critical transition energy of CdTe band structure, are chosen for the correlation since E1 gives higher resolution than the other critical transition energies. On the other hand, due to the anisotropic characteristic of (211) oriented CdTe surfaces, SE data (<ϵ2 > and ψ) shows varieties for different azimuthal angle measurements. For this reason, in order to estimate the surface roughness by considering these correlations, it is shown that SE measurements need to be taken at the same surface azimuthal angle. Estimating surface roughness in this manner is an accurate way to eliminate cumbersome surface roughness measurement by AFM.Article Citation - WoS: 4Citation - Scopus: 4Effect of Aromatic Sams Molecules on Graphene/Silicon Schottky Diode Performance(Electrochemical Society, Inc., 2016) Yağmurcukardeş, Nesli; Aydın, Hasan; Can, Mustafa; Yanılmaz, Alper; Mermer, Ömer; Okur, Salih; Selamet, YusufAu/n-Si/Graphene/Au Schottky diodes were fabricated by transferring atmospheric pressure chemical vapor deposited (APCVD) graphene on silicon substrates. Graphene/n-Si interface properties were improved by using 5-[(3-methylphenyl)(phenyl) amino]isophthalic acid (MePIFA) and 5-(diphenyl)amino]isophthalic acid (DPIFA) aromatic self-assembled monolayer (SAM) molecules. The surface morphologies of modified and non-modified films were investigated by atomic force microscopy and scanning electron microscopy. The surface potential characteristics were obtained by Kelvin-probe force microscopy and found as 0.158 V, 0.188 V and 0,383 V as a result of SAMs modification. The ideality factors of n-Si/Graphene, n-Si/MePIFA/Graphene and n-Si/DPIFA/Graphene diodes were found as 1.07, 1.13 and 1.15, respectively. Due to the chain length of aromatic organic MePIFA and DPIFA molecules, also the barrier height φB values of the devices were decreased. While the barrier height of n-Si/Graphene diode was obtained as 0.931 eV, n-Si/MePIFA/Graphene and n-Si/DPIFA/Graphene diodes have barrier height of 0.820 and 0.720 eV, respectively.