Physics / Fizik
Permanent URI for this collectionhttps://hdl.handle.net/11147/6
Browse
25 results
Filters
Settings
Search Results
Article Citation - Scopus: 1Production and Dispersion of Plasma Functionalized Carbon Nanotubes in Pan Fiber Spinning Solution With Different Surfactants(MMOB Tekstil Mühendisleri Odası, 2022) Kutlu, Bengi; Akşit, Aysun; Özyüzer, Lütfi; Yağmurcukardeş, Nesli; Selamet, YusufIn this study, the distribution of plasma-functionalized multi-walled carbon nanotubes in polyacrylonitrile nanocomposite fibers produced by wet spinning method using different surfactants (Triton-X and sodium dodecyl sulfate) was investigated. Firstly, we produced CNTs by chemical vapor deposition (CVD) technique. Secondly, low-pressure plasma functionalization of CNTs was realized. Finally, nanocomposite polyacrylonitrile fibers doped by CNTs were obtained using wet spinning technique. Properties of produced carbon nanotubes, functionalized carbon nanotubes and nanocomposite polyacrylonitrile fibers were examined by the analyses of chemical composition, surface structure, structural and mechanical properties.Article Citation - WoS: 11Citation - Scopus: 13Effect of Cnt Incorporation on Pan/Ppy Nanofibers Synthesized by Electrospinning Method(TÜBİTAK, 2020) İnce Yardımcı, Atike; Tanoğlu, Metin; Yılmaz, Selahattin; Selamet, YusufIn this study, carbon nanotubes (CNTs) added polyacrylonitrile/polypyrrole (PAN/PPy) electrospun nanofibers were produced. Average diameters of the nanofibers were measured as 268 and 153 nm for 10 and 25 wt% of PPy contents, respectively. A relatively higher strain to failure values (23.3%) were observed for the low PPy content. When as-grown CNTs (1 and 4 wt%) were added into the PAN/PPy blends, disordered nanofibers were observed to form within the microstructure. To improve the interfacial properties of CNTs/PAN/PPy composites, CNTs were functionalized with H2SO4/HNO3/HCl solution. The functionalized CNTs were well dispersed within the nanofibers and aligned along the direction of nanofibers. Therefore, beads formation on nanofibers decreased. The impedance of the nanofibers was found to decrease with the PPy content and CNT addition. These nanofibers had a great potential to be used as an electrochemical actuator or a tissue engineering scaffold.Article Mıknatıssal Saçtırma Sistemi ile Metal Kaplanan Polipropilen Liflerin Antistatik ve Antibakteriyel Özellikleri(TMMOB Tekstil Mühendisleri Odası, 2010) Özyüzer, Lütfi; Meriç, Zeynep; Selamet, Yusuf; Kutlu, Bengi; Cireli, AysunTekstil liflerini modifiye ederek, katma değeri yüksek, fonksiyonel teknik tekstil elde etmek için çeşitli yöntemler kullanılmaktadır. Örneğin, antistatik tekstiller, lifler içerisine iletken parçaçık katkılama ile elde edilebileceği gibi çeyreye kimyasal olarak zarar vermemesi dolayısıyla vakumda mıknatıssal saçtırma ile yüzeyi istenilen metali ince film olarak yüzeye kaplayarak da elde edilebilir. Bu çalışmada çapları 65 fim olan multifilament sentetik polipropilen liflerin yüzeyleri yüksek vakum altında nanometre kalınlığında Cr ve Ag gibi elektriksel iletken metal filmler ile kaplanmış ve elektriksel iletkenlik ve antibakteriyel özellikleri incelenmiştir.Article Citation - WoS: 18Citation - Scopus: 17Cnt Incorporated Polyacrilonitrile/Polypyrrole Nanofibers as Keratinocytes Scaffold(Trans Tech Publications, 2019) İnce Yardımcı, Atike; Aypek, Hande; Öztürk, Özgür; Yılmaz, Selahattin; Özçivici, Engin; Meşe, Gülistan; Selamet, YusufPolypyrrole (PPy) is an attractive scaffold material for tissue engineering with its non-toxic and electrically conductive properties. There has not been enough information about PPy usage in skin tissue engineering. The aim of this study is to investigate biocompatibility of polyacrilonitrile (PAN)/PPy nanofibrous scaffold for human keratinocytes. PAN/PPy bicomponent nanofibers were prepared by electrospinning, in various PPy concentrations and with carbon nanotube (CNT) incorporation. The average diameter of electrospun nanofibers decreased with increasing PPy concentration. Further, agglomerated CNTs caused beads and disordered parts on the surface of nanofibers. Biocompatibility of these PAN/PPy and PAN/PPy/CNT scaffolds were analyzed in vitro. Both scaffolds provided adhesion and proliferation of keratinocytes. Nanofiber diameter did not significantly influence the morphology of cells. However, with increasing number of cells, cells stayed among nanofibers and this affected their shape and size. In this study, we demonstrated that PAN/PPy and PAN/PPy/CNT scaffolds enabled the growth of keratinocytes, showing their biocompatibility.Article Citation - WoS: 4Citation - Scopus: 5Identifying Threading Dislocations in Cdte Films by Reciprocal Space Mapping and Defect Decoration Etching(American Institute of Physics, 2018) Polat, Mustafa; Bilgilisoy, Elif; Arı, Ozan; Öztürk, Orhan; Selamet, YusufWe study threading dislocation (TD) density of high-quality cadmium telluride (CdTe) layers grown on a (211) oriented GaAs substrate by molecular beam epitaxy. High-resolution X-ray diffraction was performed to calculate the density of screw-type TDs by measuring the broadening of the asymmetrical (511) Bragg reflections of CdTe epilayers. In addition, total TD densities were determined by the Everson-etching method and were compared with screw TDs. Our results show that the total TD densities in CdTe films were dominated by those with screw character. The screw component TDs are estimated to account for more than 90% of the total TD density. CdTe layers grown at a thickness of less than 3.0 μm typically exhibit the screw TD densities in the 106 cm-2 and 107 cm-2 range. It can be noted that as the nucleation temperature increases, i.e., ≥222 °C, both the area density of TDs with the screw component of the CdTe films and the total TD density are roughly four times larger than those of the epilayer grown at the nucleation temperature of 215 °C. Furthermore, we discuss the influence of the II/VI flux ratio on the density of threading dislocations. The contribution of screw TDs to the total TD density showed a significant decrease in roughly 30% in the case of a high II/VI flux ratio. We further examine the reciprocal space maps in the vicinity of the (422) reflections.Article Citation - WoS: 6Citation - Scopus: 10Effect of Annealing on the Density of Defects in Epitaxial Cdte (211)/Gaas(Springer, 2018) Bakali, Emine; Selamet, Yusuf; Tarhan, EnverCdTe thin films were grown on GaAs (211) wafers by molecular beam epitaxy as the buffer layer for HgCdTe infrared detector applications. We studied the effect of annealing on the density of dislocation of these CdTe thin films under varying annealing parameters such as annealing temperature, annealing duration, and number of cycles. Annealings were carried out using a homemade annealing reactor possessing a special heater element made of a Si wafer for rapid heating. The density of dislocations, which were made observable with a scanning electron microscope after etching with an Everson solution, were calculated by counting the number of dislocations per unit surface area, hence the term etch pit density (EPD). We were able to decrease EPD values by one order of magnitude after annealing. For example, the best EPD value after a 20-min annealing at 400°C was ∼ 2 × 107 cm−2 for a 1.63-μm CdTe thin film which was about 9.5 × 107 cm−2 before annealing. We also employed Raman scattering measurements to see the changes in the structural quality of the samples. From the Raman measurements, we were able to see improvements in the quality of our samples from the annealing by studying the ratio of 2LO/LO phonon mode Raman intensities. We also observed a clear decrease in the intensity of Te precipitations-related modes, indicating a decrease in the size and number of these precipitations.Article Citation - WoS: 8Citation - Scopus: 10Experimental and Computational Investigation of Graphene/Sams Schottky Diodes(Elsevier Ltd., 2018) Aydın, Hasan; Bacaksız, Cihan; Yağmurcukardeş, Nesli; Karakaya, Caner; Mermer, Ömer; Can, Mustafa; Senger, Ramazan Tuğrul; Şahin, Hasan; Selamet, YusufWe have investigated the effect of two different self-assembled monolayers (SAMs) on electrical characteristics of bilayer graphene (BLG)/n-Si Schottky diodes. Novel 4″bis(diphenylamino)-1, 1′:3″-terphenyl-5′ carboxylic acids (TPA) and 4,4-di-9H-carbazol-9-yl-1,1′:3′1′-terphenyl-5′ carboxylic acid (CAR) aromatic SAMs have been used to modify n-Si surfaces. Cyclic voltammetry (CV) and Kelvin probe force microscopy (KPFM) results have been evaluated to verify the modification of n-Si surface. The current–voltage (I–V) characteristics of bare and SAMs modified devices show rectification behaviour verifying a Schottky junction at the interface. The ideality factors (n) from ln(I)–V dependences were determined as 2.13, 1.96 and 2.07 for BLG/n-Si, BLG/TPA/n-Si and BLG/CAR/n-Si Schottky diodes, respectively. In addition, Schottky barrier height (SBH) and series resistance (R s ) of SAMs modified diodes were decreased compared to bare diode due to the formation of a compatible interface between graphene and Si as well as π–π interaction between aromatic SAMs and graphene. The CAR-based device exhibits better diode characteristic compared to the TPA-based device. Computational simulations show that the BLG/CAR system exhibits smaller energy-level-differences than the BLG/TPA, which supports the experimental findings of a lower Schottky barrier and series resistance in BLG/CAR diode.Article Citation - WoS: 7Citation - Scopus: 7Stable Ultra-Thin Cdte Crystal: a Robust Direct Gap Semiconductor(IOP Publishing Ltd., 2017) İyikanat, Fadıl; Akbalı, Barış; Kang, J.; Senger, Ramazan Tuğrul; Selamet, Yusuf; Şahin, HasanEmploying density functional theory based calculations, we investigate structural, vibrational and strain-dependent electronic properties of an ultra-thin CdTe crystal structure that can be derived from its bulk counterpart. It is found that this ultra-thin crystal has an 8-atom primitive unit cell with considerable surface reconstructions. Dynamic stability of the structure is predicted based on its calculated vibrational spectrum. Electronic band structure calculations reveal that both electrons and holes in single layer CdTe possess anisotropic in-plane masses and mobilities. Moreover, we show that the ultra-thin CdTe has some interesting electromechanical features, such as strain-dependent anisotropic variation of the band gap value, and its rapid increase under perpendicular compression. The direct band gap semiconducting nature of the ultra-thin CdTe crystal remains unchanged under all types of applied strain. With a robust and moderate direct band gap, single-layer CdTe is a promising material for nanoscale strain dependent device applications.Article Citation - WoS: 13Citation - Scopus: 16Synthesis and Characterization of Cationic Lipid Coated Magnetic Nanoparticles Using Multiple Emulsions as Microreactors(Elsevier Ltd., 2017) Akbaba, Hasan; Karagöz, Uğur; Selamet, Yusuf; Kantarcı, A. GültenThe aim of this study was to develop a novel iron oxide nanoparticle synthesis method with in-situ surface coating. For this purpose multiple emulsions were used as microreactors for the first time and magnetic iron oxide particles synthesized in the core of cationic solid lipid nanoparticles. DLS, SEM, TEM, VSM, Raman Spectrometer, XRD, and XPS techniques were performed for characterization of the magnetic nanoparticles. Obtained magnetic nanoparticles are superparamagnetic and no additional process was needed for surface adjustments. They are positively charged as a result of cationic lipid coating and has appropriate particle size (<30 nm) for drug or nucleic acid delivery. Structure analysis showed that magnetic core material is in the form of magnetite. Saturation magnetization value was measured as 15–17 emu g−1 for lipid coated magnetic nanoparticles obtained by multiple emulsion method which is reasonably sufficient for magnetic targeting.Article Citation - WoS: 13Citation - Scopus: 16Reciprocal Space Mapping Study of Cdte Epilayer Grown by Molecular Beam Epitaxy on (2 1 1)b Gaas Substrate(IOP Publishing Ltd., 2017) Polat, Mustafa; Arı, Ozan; Öztürk, Orhan; Selamet, YusufWe examine high quality, single crystal CdTe epilayer grown by molecular beam epitaxy (MBE) on (2 1 1)B GaAs substrate using both positions and full width at half maximums (FWHMs) of reciprocal lattice points (RLPs). Our results demonstrate that reciprocal space mapping (RSM) is an effective way to study the structural characteristics of the high-index oriented epitaxial thin films having a large lattice mismatch with the substrate. The measurement method is defined first, and then the influence of shear strain ( xz) on the position of the (5 1 1) node of epilayer is clarified. It is concluded that the lattice tilting is likely to be related with the lattice mismatch. Nondestructive measurement of the dislocation density is achieved by applying the mosaic crystal model. The screw dislocation density, estimated to be 7.56×107 cm2, was calculated utilizing the broadened peakwidths of the asymmetric RLP of the epilayer lattice.
- «
- 1 (current)
- 2
- 3
- »