Physics / Fizik
Permanent URI for this collectionhttps://hdl.handle.net/11147/6
Browse
22 results
Search Results
Article Citation - WoS: 3Citation - Scopus: 4Terahertz Wavefront Engineering Using a Hard-Coded Metasurface(Springer, 2023) Noori, Aileen; Akyürek, Bora; Demirhan, Yasemin; Özyüzer, Lütfi; Güven, Kaan; Altan, Hakan; Aygün, GülnurDuring the past few years, coding metamaterials (MM) drew significant attention, where the far-field scattering/transmission pattern of the electromagnetic wave (particularly in the THz regime) can be encoded into a single or few-bit digitized phase-response of the metasurface, thereby enabling a full digital control. Single-bit MMs contain two types of unit cells where the phase becomes 0 and 1 (in units of ?), respectively. By arranging these unit cells into a 2D surface pattern, the THz wavefront can be shaped. In this work, a novel hard-coded metasurface was designed, fabricated, and experimentally investigated for multi-beam reflection of incident THz beam. The design employs stripe and checkerboard patterns of bilayer MM unit cells consisting of square gold patches with a polymer spacing layer from a gold backplane. Experimental and simulation results show that the incident wave in the 0.500–0.750 THz range can be reflected with > 95% efficiency in uniform amplitude and 1-bit coded phase. For the checkerboard metasurface pattern, the measured and analytically calculated reflection angle shows good agreement. The metasurface design is suitable for large-scale fabrication and can potentially be used as a template in the development of actively coded metasurfaces. © 2023, The Author(s), under exclusive licence to Springer Science+Business Media, LLC, part of Springer Nature.Article Citation - WoS: 4Citation - Scopus: 5Enhanced Optoelectronic Properties of Magnetron Sputtered Ito/Ag Multilayers by Electro-Annealing(AVS, 2022) Uyanık, Zemzem; Türkoğlu, Fulya; Köseoğlu, Hasan; Ekmekçioğlu, Merve; Ata, Bengü; Demirhan, Yasemin; Özdemir, Mehtap; Aygün, Gülnur; Özyüzer, LütfiIndium tin oxide/silver/indium tin oxide (ITO/Ag/ITO) multilayers have attracted much attention to fulfill the growing need for high-performance transparent conducting oxide electrodes. To make these transparent multilayers work better, electro-annealing, which is a method of self-heating by electric current, can be effective. Moreover, the effect of current on ITO/Ag/ITO multilayers should be investigated to make sure that electronic devices will be reliable over their lifetime. In this study, ITO/Ag/ITO multilayer electrodes with varying Ag thicknesses were grown by DC magnetron sputtering at room temperature. Structural, optical, and electrical properties of these multilayers were investigated before and after electro-annealing. Measurement results revealed that improved optical transmittance and sheet resistance can be obtained by the optimization of Ag thickness for the as-grown ITO/Ag/ITO layers. The highest figure of merit (FoM) value of 17.37 × 10−3 Ω−1 with optical transmittance of 85.15% in the visible region and sheet resistance of 11.54 Ω/□ was obtained for the Ag thickness of 16.5 nm for as-grown samples. The electro-annealing of as-grown ITO/Ag/ITO multilayers led to improved optical behavior of the multilayer structure over a wide spectral range, especially in the near-infrared range. Electro-annealing also provided an improvement in the crystallinity and sheet resistance of the electrodes. The improvement of the electrical and optical properties of the structure enabled a FoM of 23.07 × 10−3 Ω−1 with the optical transmittance of 86.80% in the visible region and sheet resistance of 10.52 Ω/□. The findings of this work provide proper knowledge of the properties of ITO/Ag/ITO multilayers under electrical current and suggest that the overall performance of the multilayers can be improved by the electro-annealing process.Conference Object Investigation of In-Gap Field Enhancement at Terahertz Frequencies for a Metasurface Enhanced Sensor(Institute of Electrical and Electronics Engineers, 2021) Tugay, Halime; Altan, Hakan; Demirhan, Yasemin; Özyüzer, Lütfi; Sabah, CumaliThe arrangements of subwavelength inclusions in a metasurface can serve as an effective absorber for the terahertz region. When such an absorber is combined with a unique material, the absorption can induce effects that can lead to a change in the materials electrical properties. Vanadium dioxide shows a passive and reversible change from monoclinic insulator phase to metallic tetragonal rutile structure by using external stimuli such as temperature (340K), photo excitation, electric field, mechanical strain or magnetic field [1,2]. Upon absorption of the THz radiation, the high electric fields that are generated inside the gaps of the metasurface can serve as trigger points, as was shown previously using kV strength THz E-fields.Article Citation - WoS: 6Citation - Scopus: 6Nanolitography Based on Electrospun and Etched Nanofibers(Elsevier, 2021) Noori, Aileen; Döğer, Hilal; Demirhan, Yasemin; Özdemir, Mehtap; Özyüzer, Lütfi; Aygün, Gülnur; Sağlam, ÖzgeIn this study, we propose a new type of nanolithography procedure to fabricate orderly patterned metallic nanostructures using the electrohydrodynamic method and the reactive ion etching process. The electrohydrodynamic process parameters were tuned so as to create patterning with precision, and fibers in nanoscale on silver-coated substrates. We also studied reactive ion etching with different durations on the well-patterned samples. The experiments show that applying a voltage of 400 V resulted in straight patterned fibers with a diameter of 208.7 ? 30.3 nm. The statistical analysis on scanning electron microscope (SEM) images showed a significant difference in the diameter of the fibers fabricated at 400 V compared to those at 500 V and 600 V. We also confirm that the etching process has no affect on the fiber diameter. Moreover, electron dispersive X-Ray spectrometer (EDX) results suggest that an etching duration of 7 min is sufficient to remove the silver coating that is not covered with the fibers, and protect the silver nanostructures underneath the fibers. Utilizing a lowcost nanolithography procedure, we obtain the orderly patterned silver nanostructures for possible integration into miniaturized devices.Article Citation - WoS: 2Citation - Scopus: 2In-Situ Thin Film Copper-Copper Thermocompression Bonding for Quantum Cascade Lasers(Springer, 2021) Rouhi, Sina; Özdemir, Mehtap; Ekmekçioğlu, Merve; Yiğen, Serap; Demirhan, Yasemin; Szerling, Anna; Kosiel, Kamil; Kozubal, Maciej; Kruszka, Renata; Prokaryn, Piotr; Ertuğrul, Mehmet; Reno, John L.; Aygün, Gülnur; Özyüzer, LütfiThe choice of metals, bonding conditions and interface purity are critical parameters for the performance of metal-metal bonding quality for quantum cascade lasers (QCLs). Here, we present a novel approach for the thermocompression bonding of Cu-Cu thin films on GaAs-based waveguides without having any oxide phase, contamination or impurities at the interface. We designed a hybrid system in which magnetron sputtering of Ta, thermal evaporation of Cu and Cu-Cu thermocompression bonding processes can be performed sequentially under high vacuum conditions. GaAs/Ta/Cu and Cu/Ta/GaAs structures were thermocompressionally bonded in our in-situ homebuilt bonding system by optimizing the deposition parameters and bonding conditions. The grown thin film and the obtained interfaces were characterized using x-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive x-ray spectroscopy (EDX) techniques. The optimum Ta and Cu films' thicknesses were found to be about 20 nm and 500 nm, respectively. EDX analysis showed that the Ta thin film interlayer diffused into the Cu structure, providing better adhesivity and rigidity for the bonding. Additionally, no oxidation phases were detected at the interface. The best bonding quality was obtained when heated up to 430 degrees C with an applied pressure of 40 MPa during bonding process.Book Part Citation - Scopus: 1Thz Sources and Detectors Fabricated From High Temperature Superconductors(Springer, 2021) Demirhan, Yasemin; Türkoğlu, Fulya; Altan, Hakan; Sabah, Cumali; Özyüzer, LütfiHigh temperature superconductors have unique properties that can be useful in the THz region, single crystal constituted from superconducting CuO2-layers could sustain high voltages across the junctions and they are coupled through the intrinsic Josephson Effect this maintains the potential for very intense, coherent radiation which spreads over the THz gap. We investigated various experimental techniques to fabricate THz sources, bolometers and filters for efficient THz emission and detection. Rectangular mesa structures were fabricated on Bi2Sr2CaCu2O8-x (Bi2212) single crystal superconductors using standard e-beam lithography and Ar ion beam etching systems and an emitted power as high as 60 ?W at frequencies up to 0.85 THz was detected from micron sized continuous wave terahertz sources. We also fabricated bolometric microchips for THz detection purpose from Bi2212 single crystals. Bi2212 microchips detected the signals and response time were calculated, our results have clearly shown that Bi2212 single crystals are potential candidates for THz detection. The detection properties and sensitivity of bolometer chips can be further improved by integrating an antenna and filter structures. In order to investigate this we have fabricated metamaterial THz filters based on metals and YBa2Cu3Ox superconducting thin films with metal-mesh shape and a unique fourcross shape pattern. Both a THz time domain spectrometer and a Fourier transform infrared spectrometer (FTIR) were used to investigate the performance of these filters and the results were compared with simulations done with a commercially available electromagnetic simulation software. © Springer Nature B.V. 2021.Conference Object Reactive Ion Beam Etching of Superconducting Bi2212 by Ta/Pr and Pr'/ta/pr Masks for the Generation of Thz Waves(Institute of Electrical and Electronics Engineers Inc., 2009) Köseoğlu, Hasan; Türkoğlu, Fulya; Demirhan, Yasemin; Meriç Polster, Zeynep; Özyüzer, LütfiGeneration of powerful THz radiation from intrinsic Josephson Junctions (Ills) of Bi(2)Sr(2)CaCu(2)O(8+delta) (Bi2212) may require mesas with large lateral dimension. However, there are difficulties in fabrication of perfect rectangular mesas. Mesa lateral angles should be close to 90 degrees to obtain IJJs with same planar dimensions for synchronization of IJJs. Since thick photoresist (PR) layer shades the lateral dimension of mesa during ion beam etching, we patterned Ta/PR and PR'/Ta/PR masks on Bi2212 and used selective ion etching to overcome this problem. The reactive ion beam etchings have done with ion beam of Ar, N(2) and O(2) and we have obtained mesas about 1 mu m with lateral angle of approximately 50 to 75 degrees which is better than the mesas fabricated with single layer mask.Conference Object Terahertz Transmission Through Patterened Vanadium Oxide Thin Films on Dielectric Substrates(SCITEPRESS, 2017) Akkaya, M.; Demirhan, Yasemin; Yüce, Hürriyet; Aygün, Gülnur; Özyüzer, Lütfi; Sabah, Cumali; Altan, HakanPatterned and unpatterned films of vanadium oxide grown on dielectric substrates such as fused silica and sapphire were grown and analysed by varying the temperature using terahertz time domain spectroscopy. After investigating the critical transition temperature near 340K, a well-known cross-shaped pattern was studied to observe any resonances upon transmission. Due to the poor conductivity of the films the frequency selective nature of the structure was not observed, however an etalon effect could be seen in the sapphire substrate as opposed to the fused silica substrate above the critical temperature. Dependence of the refractive index difference between substrates upon transmission of the THz pulse is likely in explaining this observed difference.Article Citation - WoS: 31Citation - Scopus: 33The Controllable Deposition of Large Area Roll-To Sputtered Ito Thin Films for Photovoltaic Applications(Elsevier, 2020) Demirhan, Yasemin; Köseoğlu, Hasan; Türkoğlu, Fulya; Uyanık, Zemzem; Özdemir, Mehtap; Aygün, Gülnur; Özyüzer, LütfiIn the present study, using a large area roll-to-roll DC magnetron sputtering system deposition of ITO thin films on polyethylene terephthalate (PET) substrates were achieved. In order to investigate the effect of growth conditions on the film properties all through the deposition process, optical emission spectroscopy (OES) analysis have been accomplished in a governable way. The consequences of Oxygen partial pressure and film thickness on electrical, and optical properties of the films were determined. It was shown that the intensity of optical emission peaks are subjected to the discharge power and as well as the O-2/Ar flow ratio. Large area, uniform ITO films with relatively high transparency and low electrical resistivity (R(2)(<)50 Omega/sqr) were succesfully deposited on PET substrates. The significance of both the figure of merit (FOM) and the optical band gap values on the performance of different TCO thin films were addressed. In this work, the obtained results suggest that the overall performance is sufficient to implement the ITO films in photovoltaic and OLED applications. (C) 2019 Elsevier Ltd. All rights reserved.Conference Object Citation - Scopus: 1Cleo®/Europe - Eqec 2015, an Indium Tin Oxide Metamaterial Filter for the Terahertz Regime: Design, Fabrication and Characterization(Optical Society of America (OSA), 2015) Takan, Taylan; Nebioğlu, Mehmet Ali; Kurt, Metin; Demirhan, Yasemin; Özyüzer, Lütfi; Sabah, Cumali; Altan, Hakan[No abstract available]
- «
- 1 (current)
- 2
- 3
- »