Physics / Fizik
Permanent URI for this collectionhttps://hdl.handle.net/11147/6
Browse
11 results
Search Results
Article Citation - WoS: 9Citation - Scopus: 9High Voltage Response of Graphene/4h-sic Uv Photodetector With Low Level Detection(Elsevier, 2023) Jehad, Ala K.; Ünverdi, Özhan; Çelebi, CemA self-powered graphene/silicon carbide (G/4H-SiC) ultraviolet photodetector of a p-i-n like-structure with high voltage response has been fabricated to detect and measure low intensity ultraviolet (UV) radiation. Bilayer graphene sheet grown by chemical vapor deposition (CVD) method was transferred on the top of an epilayer structure of n-/n+ 4 H-SiC. In this structure, two Schottky contacts were formed: one at G/ n- 4H-SiC interface and the other at bulk-4 H-SiC/Cr/Au interface. The photodetector's characteristic measurements revealed low dark current of - 0.58 nA and spectral voltage responsivity of - 0.75 V/W at 300 nm wavelength. Under low level UV illumination of 300 nm wavelength, the photodetector exhibited a leakage current and a photogenerated response voltage of 1.1 nA and 10 mV, respectively. The time-dependent photovoltage measurements displayed a rapid photovoltage response with rise and decay times of -74 ns and - 580 ns, respectively. This novel device holds promise for applications requiring sensitive and self-powered UV detection.Article Citation - WoS: 35Citation - Scopus: 35Cvd Graphene/Sic Uv Photodetector With Enhanced Spectral Responsivity and Response Speed(Elsevier, 2023) Jehad, Ala K.; Fidan, Mehmet; Ünverdi, Özhan; Çelebi, CemA self-powered, high-performance graphene/Silicon Carbide (G/4H-SiC) ultraviolet Schottky junction photodetector has been fabricated, and the effect of using monolayer and bilayer graphene on the device performance parameters was investigated. P-type graphene sheets were grown by the chemical vapor deposition (CVD) method, while 4H-SiC material consists of an epilayer structure of n-/n+ on bulk n-SiC. Two photodetector devices have been studied, one with monolayer graphene (MLG) and the other with bilayer graphene (BLG). The proposed photodetector structure reveals the highest spectral responsivity known of a G/4H-SiC UV photodetector so far. Electronic and optoelectronic characterizations were done under an ultraviolet wavelength range from 240 to 350 nm. The results show two spectral responsivity maxima (Rmax) at 285 nm and 300 nm wavelengths. Exhibiting two maxima in spectral responsivity and detectivity is caused by the constructive and destructive interference effects of multiple reflections at the SiC epilayer's interfaces. The photodetector devices exhibit high spectral responsivity (R ? 0.09 AW?1), maximum detectivity (D* ? 2.9 × 1012 Jones), and minimum noise equivalent power (NEP ? 0.17 pWHz-1/2) in both devices. Using bilayer graphene instead of monolayer showed no significant change in both the photogenerated current and the spectral responsivity due to the higher absorption coefficient of bilayer graphene, however, it exhibited a significant improvement in the response speed. The response speed was found to increase by 50 % when bilayer graphene was used as a hole collecting electrode in the G/4H-SiC junction. This is because bilayer graphene creates a narrower depletion layer and higher electric field, which promotes efficient charge separation and recombination. © 2023 Elsevier B.V.Article Citation - WoS: 5Citation - Scopus: 5Self-Powered Photodetector Array Based on Individual Graphene Electrode and Silicon-On Integration(Elsevier, 2023) Yanılmaz, Alper; Ünverdi, Özhan; Çelebi, CemOne of the key limitations for the device performance of the silicon (Si) based photodetector arrays is the optical crosstalk effect encountered between photoactive elements as well. The scope of this work is to reduce optical crosstalk and thus increasing the device performances with graphene and Si integration. This paper presents the design, fabrication process, and performance evaluation of self-powered individual Graphene/Silicon on Insulator (GSOI) based Schottky barrier photodiode array (PDA) devices. A 4-element GSOI Schottky barrier PDA with separate graphene electrodes is fabricated to examine possible optical crosstalk encountered between each diode in the array structure. Here, monolayer graphene is utilized as hole collecting separate electrode on individually arrayed n-type Si on SOI substrate by photolithography technique. Each diode in the array exhibited a clear rectifying Schottky character. Photoresponse characterizations revealed that all diodes had excellent device performance even in self-powered mode in terms of an Ilight/Idark ratio up to 104, a responsivity of ∼0.12 A/W, a specific detectivity of around 1.6 × 1012 Jones, and a response speed of ∼1.32 μs at 660 nm wavelength. As revealed by optical crosstalk measurement, the device with pixel pitch of 1.5 mm had a total crosstalk of about 0.10% (−60 dB) per array. These results showed that the optical crosstalk between neighboring n-Si elements can be greatly minimized when graphene is used as separated electrode on arrayed Si on SOI substrate. Our study is expected give an insight into the performance characteristics of GSOI PDA devices which have great potential to be used in many technological applications such as multi-wavelength light measurement, level metering, high-speed photometry and position/motion detection. © 2023 Elsevier B.V.Article Citation - WoS: 4Citation - Scopus: 4Graphene/Soi-based Self-Powered Schottky Barrier Photodiode Array(American Institute of Physics, 2022) Yanılmaz, Alper; Fidan, Mehmet; Ünverdi, Özhan; Çelebi, CemWe have fabricated a four-element graphene/silicon on insulator (SOI) based Schottky barrier photodiode array (PDA) and investigated its optoelectronic device performance. In our device design, monolayer graphene is utilized as a common electrode on a lithographically defined linear array of n-type Si channels on a SOI substrate. As revealed by wavelength resolved photocurrent spectroscopy measurements, each element in the PDA structure exhibited a maximum spectral responsivity of around 0.1 A/W under a self-powered operational mode. Time-dependent photocurrent spectroscopy measurements showed excellent photocurrent reversibility of the device with ∼1.36 and ∼1.27 μs rise time and fall time, respectively. Each element in the array displayed an average specific detectivity of around 1.3 × 1012 Jones and a substantially small noise equivalent power of ∼0.14 pW/Hz-1/2. The study presented here is expected to offer exciting opportunities in terms of high value-added graphene/Si based PDA device applications such as multi-wavelength light measurement, level metering, high-speed photometry, and position/motion detection.Article Citation - WoS: 7Citation - Scopus: 6Anisotropic Etching of Cvd Grown Graphene for Ammonia Sensing(Institute of Electrical and Electronics Engineers Inc., 2022) Yağmurcukardeş, Nesli; Bayram, Abdullah; Aydın, Hasan; Yağmurcukardeş, Mehmet; Açıkbaş, Yaser; Peeters, François M.; Çelebi, CemBare chemical vapor deposition (CVD) grown graphene (GRP) was anisotropically etched with various etching parameters. The morphological and structural characterizations were carried out by optical microscopy and the vibrational properties substrates were obtained by Raman spectroscopy. The ammonia adsorption and desorption behavior of graphene-based sensors were recorded via quartz crystal microbalance (QCM) measurements at room temperature. The etched samples for ambient NH3 exhibited nearly 35% improvement and showed high resistance to humidity molecules when compared to bare graphene. Besides exhibiting promising sensitivity to NH3 molecules, the etched graphene-based sensors were less affected by humidity. The experimental results were collaborated by Density Functional Theory (DFT) calculations and it was shown that while water molecules fragmented into H and O, NH3 interacts weakly with EGPR2 sample which reveals the enhanced sensing ability of EGPR2. Apparently, it would be more suitable to use EGRP2 in sensing applications due to its sensitivity to NH3 molecules, its stability, and its resistance to H2O molecules in humid ambient.Article Citation - WoS: 1Citation - Scopus: 1Substrate Effects on Electrical Parameters of Dirac Fermions in Graphene(Elsevier, 2021) Tıraş, Engin; Ardalı, Şükrü; Fırat, Hakan Asaf; Arslan, Engin; Özbay, EkmelThe substrate effects on the electronic transport properties of single-layer graphene on TiO2/Si substrate have been studied. The Hall mobility, sheet carrier density, and transport lifetime were obtained from the temperature-dependent Hall measurements, while the in-plane effective mass, quantum lifetime was obtained from the temperature-dependent variation of the Shubnikov de Haas (SdH) oscillations that were made at 1.8 to 45 K temperature range and up to the magnetic field of 11 T. The measurement results showed that in SLG/TiO2/ Si sample, there were 2.36 +/- 0.12x1016 m-3 amounts of 3D carriers coming from the substrate. In our previous studies, 3D carrier densities were measured as 6.07x1016 m-3 and zero for SLG/SiO2/Si and SLG/SiC sample, respectively. This result shows that the 3D carriers formed in the structure are significantly changed by a substrate. The scattering mechanisms were determined using the zt/zq ratio. The ratio values obtained as 3.66. This value obtained was compared with the values we found for SLG/SiC (zt/zq=1.36) sample and SLG/TiO2/Si (zt/zq=3.08) sample our previous study. The results show that small-angle scattering is dominant in SLG/SiC sample, but large-angle scattering is dominant in SLG/SiO2/Si and SLG/TiO2/Si samples. The charged impurity scattering is the dominant scattering mechanism in SLG/TiO2/Si and SLG/SiO2/Si samples, whereas in SLG/SiC samples, a short-range scattering mechanism such as lattice defects can be said to affect the electronic transport.Article Citation - WoS: 12Citation - Scopus: 17Junction Area Dependent Performance of Graphene/Silicon Based Self-Powered Schottky Photodiodes(Elsevier, 2021) Fidan, Mehmet; Ünverdi, Özhan; Çelebi, CemThis work reports the impact of junction area on the device performance parameters of Graphene/n-Silicon (Gr/n-Si) based Schottky photodiodes. Herein, three batches of Gr/n-Si photodiode samples were produced based on various sized CVD grown monolayer graphene layers transferred on individual n-Si substrates. The fabricated devices exhibited strong Schottky diode character and had high spectral sensi-tivity at 905 nm peak wavelength. The optoelectronic measurements showed that the spectral response of Gr/n-Si Schottky photodiodes has a linear dependence on the active junction area. The sample with 20 mm(2) junction area reached a spectral response of 0.76 AW(-1), which is the highest value reported in the literature for self-powered Gr/n-Si Schottky photodiodes without the modification of graphene electrode. In contrast to their spectral responsivities, the response speed of the samples were found to be lowered as a function of the junction area. The experimental results demonstrated that the device performance of Gr/n-Si Schottky photodiodes can be modified simply by changing the size of the graphene electrode on n-Si without need of external doping of graphene layer or engineering Gr/n-Si interface. This study may serve towards the standardization of junction area for the development of high performance Gr/Si based optoelectronic devices such as solar cells and photodetectors operating in between the ultraviolet and near-infrared spectral region. (C) 2021 Elsevier B.V. All rights reserved.Article Citation - WoS: 2Citation - Scopus: 2Tuning Thermal Transport in Graphene Via Combinations of Molecular Antiresonances(Elsevier Ltd., 2018) Sevim, Koray; Sevinçli, HaldunWe propose a method to engineer the phonon thermal transport properties of low dimensional systems. The method relies on introducing a predetermined combination of molecular adsorbates, which give rise to antiresonances at frequencies specific to the molecular species. Despite their dissimilar transmission spectra, thermal resistances due to individual molecules remain almost the same for all species. On the other hand, thermal resistance due to combinations of different species are not additive and show large differences depending on the species. Using a toy model, the physics underlying the violation of resistance summation rule is investigated. It is demonstrated that equivalent resistance of two scatterers having the same resistances can be close to the sum of the constituents or ∼ 70% of it depending on the relative positions of the antiresonances. The relative positions of the antiresonances determine the net change in transmission, therefore the equivalent resistance. Since the entire spectrum is involved in phonon spectrum changes in different parts of the spectrum become important. Performing extensive first-principles based computations, we show that these distinctive attributes of phonon transport can be useful to tailor the thermal transport through low dimensional materials, especially for thermoelectric and thermal management applications.Article Citation - WoS: 8Citation - Scopus: 10Experimental and Computational Investigation of Graphene/Sams Schottky Diodes(Elsevier Ltd., 2018) Aydın, Hasan; Bacaksız, Cihan; Yağmurcukardeş, Nesli; Karakaya, Caner; Mermer, Ömer; Can, Mustafa; Senger, Ramazan Tuğrul; Şahin, Hasan; Selamet, YusufWe have investigated the effect of two different self-assembled monolayers (SAMs) on electrical characteristics of bilayer graphene (BLG)/n-Si Schottky diodes. Novel 4″bis(diphenylamino)-1, 1′:3″-terphenyl-5′ carboxylic acids (TPA) and 4,4-di-9H-carbazol-9-yl-1,1′:3′1′-terphenyl-5′ carboxylic acid (CAR) aromatic SAMs have been used to modify n-Si surfaces. Cyclic voltammetry (CV) and Kelvin probe force microscopy (KPFM) results have been evaluated to verify the modification of n-Si surface. The current–voltage (I–V) characteristics of bare and SAMs modified devices show rectification behaviour verifying a Schottky junction at the interface. The ideality factors (n) from ln(I)–V dependences were determined as 2.13, 1.96 and 2.07 for BLG/n-Si, BLG/TPA/n-Si and BLG/CAR/n-Si Schottky diodes, respectively. In addition, Schottky barrier height (SBH) and series resistance (R s ) of SAMs modified diodes were decreased compared to bare diode due to the formation of a compatible interface between graphene and Si as well as π–π interaction between aromatic SAMs and graphene. The CAR-based device exhibits better diode characteristic compared to the TPA-based device. Computational simulations show that the BLG/CAR system exhibits smaller energy-level-differences than the BLG/TPA, which supports the experimental findings of a lower Schottky barrier and series resistance in BLG/CAR diode.Article Citation - WoS: 11Citation - Scopus: 11The Effect of Adsorbates on the Electrical Stability of Graphene Studied by Transient Photocurrent Spectroscopy(American Institute of Physics, 2018) Kalkan, Sırrı Batuhan; Aydın, H.; Özkendir, Dicle; Çelebi, CemAdsorbate induced variations in the electrical conductivity of graphene layers with two different types of charge carriers are investigated by using the Transient Photocurrent Spectroscopy (TPS) measurement technique. In-vacuum TPS measurements taken for a duration of 5 ks revealed that the adsorption/desorption of atmospheric adsorbates leads to more than a 110% increment and a 45% decrement in the conductivity of epitaxial graphene (n-type) and chemical vapor deposition graphene (p-type) layers on semi-insulating silicon carbide (SiC) substrates, respectively. The graphene layers on SiC are encapsulated and passivated with a thin SiO2 film grown by the Pulsed Electron Deposition method. The measurements conducted for short periods and a few cycles showed that the encapsulation process completely suppresses the time dependent conductivity instability of graphene independent of its charge carrier type. The obtained results are used to construct an experimental model for identifying adsorbate related conductivity variations in graphene and also in other 2D materials with an inherently high surface-to-volume ratio.