Physics / Fizik
Permanent URI for this collectionhttps://hdl.handle.net/11147/6
Browse
18 results
Search Results
Article Citation - WoS: 2Citation - Scopus: 2In-Situ Thin Film Copper-Copper Thermocompression Bonding for Quantum Cascade Lasers(Springer, 2021) Rouhi, Sina; Özdemir, Mehtap; Ekmekçioğlu, Merve; Yiğen, Serap; Demirhan, Yasemin; Szerling, Anna; Kosiel, Kamil; Kozubal, Maciej; Kruszka, Renata; Prokaryn, Piotr; Ertuğrul, Mehmet; Reno, John L.; Aygün, Gülnur; Özyüzer, LütfiThe choice of metals, bonding conditions and interface purity are critical parameters for the performance of metal-metal bonding quality for quantum cascade lasers (QCLs). Here, we present a novel approach for the thermocompression bonding of Cu-Cu thin films on GaAs-based waveguides without having any oxide phase, contamination or impurities at the interface. We designed a hybrid system in which magnetron sputtering of Ta, thermal evaporation of Cu and Cu-Cu thermocompression bonding processes can be performed sequentially under high vacuum conditions. GaAs/Ta/Cu and Cu/Ta/GaAs structures were thermocompressionally bonded in our in-situ homebuilt bonding system by optimizing the deposition parameters and bonding conditions. The grown thin film and the obtained interfaces were characterized using x-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive x-ray spectroscopy (EDX) techniques. The optimum Ta and Cu films' thicknesses were found to be about 20 nm and 500 nm, respectively. EDX analysis showed that the Ta thin film interlayer diffused into the Cu structure, providing better adhesivity and rigidity for the bonding. Additionally, no oxidation phases were detected at the interface. The best bonding quality was obtained when heated up to 430 degrees C with an applied pressure of 40 MPa during bonding process.Article Citation - WoS: 5Citation - Scopus: 5Comparison of Characteristic Properties of Al, Ga, and In-Doped Zno Thin Films Formed by Sol-Gel Method(Academic Press, 2021) Horzum, Şeyda; Bulduk, Emel; Şener, Deniz; Serin, TülayHerein, we examine the effect of doping with Indium (In), Gallium (Ga), and Aluminum (Al) (group III elements) on the structural, optical, and vibrational properties of ZnO thin films. The characteristic properties of the ZnO films prepared by the sol-gel dip-coating method are explored by utilizing X-ray diffraction, optical spectroscopy, and Raman scattering measurements. XRD analyzes exhibit that the crystallite size reduces upon doping by Ga and Al, while it increases with In, and all films have hexagonal wurtzite structure. Additionally, Raman measurements indicate that the dominant two peaks at around 104 and 445 cm(-1) are related to E(2)(low )and E-2(high) phonon modes of ZnO, respectively. The low-frequency mode (E-2(low)) is affected by dopant atoms, whereas the high-frequency mode (E-2(high)) of the wurtzite phase is not influenced by the dopant. Moreover, E-dop.atom phonon mode appears at low frequencies and the intensity ratio, I(E-dop.atom)/I(E(2)low), decreases as the ionic radius of dopant atoms increases. UV-Vis spectra reveal that the film transparency, optical band gap, Urbach energy, and refraction index can be effectively tuned by dopant atoms.Article Citation - WoS: 50Citation - Scopus: 52Monitoring the Characteristic Properties of Ga-Doped Zno by Raman Spectroscopy and Atomic Scale Calculations(Elsevier, 2019) Horzum, Şeyda; İyikanat, Fadıl; Senger, Ramazan Tuğrul; Çelebi, Cem; Sbeta, Mohamed; Yıldız, Abdullah; Serin, TülayWe experimentally and theoretically study how the structural and vibrational properties of zinc oxide (ZnO) are modified upon Gallium (Ga) doping. The characteristics of Ga-doped ZnO thin films which are synthesized by sol-gel spin coating method on glass substrates are monitored by using X-ray diffraction (XRD) and Raman scattering measurements. For atomic-level understanding of the experimental findings state-of-the-art density functional theory (DFT) based calculations are also performed. DFT calculations reveal that both the substitution and adsorption of Ga atoms in ZnO are energetically possible and substitutional doping in ZnO is the most favourable scenario. XRD measurements show that all the films are in wurtzite structure and the crystallite size of the films decreases with increasing Ga doping. In addition, Raman analysis show that strong vibrational modes at about 100 and 441 cm(-1) are associated with E-2(low) and E-2(high) phonon branches of ZnO, respectively. While the frequency of the E-2(low) mode downshifts with increasing Ga concentration, the E-2(high) phonon mode is not affected by the Ga doping. Furthermore, E-Ga phonon branch, stemming from the substituted Ga atoms, emerges at low frequencies. It is also seen that the Raman intensity of the E-G(a) peak linearly increases with increasing Ga concentration. Experimental results on the vibrational properties are in good agreement with the ab initio phonon calculations. (C) 2018 Elsevier B.V. All rights reserved.Article Citation - WoS: 22Citation - Scopus: 27Mechanisms Behind Slow Photoresponse Character of Pulsed Electron Deposited Zno Thin Films(Elsevier, 2020) Özdoğan, Mehmet; Çelebi, Cem; Utlu, GökhanSemiconducting Zinc Oxide (ZnO) is ideal candidate for ultraviolet (UV) photodetector due to its promising optoelectronic properties. Photoconductive type ZnO photodetectors, which is fabricated in metal-semiconductor-metal configuration, show mostly very high photoconductivity under UV light, but they are plagued by slow photoresponse time as slow as several tens of hours, even more. Most of the studies claimed that atmospheric adsorbates such as water and oxygen create charge traps states on the surface and remarkably increase both the photoconductivity and response time. There are also limited studies, which claim that the defect states acting as hole trap centers prolong response time significantly. However, the underlying physical mechanism is still unclear. Here we study the effects of both adsorbates and defect-related states on the photoresponse character of Pulsed Electron Deposited ZnO thin films. In order to distinguish between these two mechanisms, we have compared the time-dependent photoresponse measurements of bare-ZnO and SiO2 encapsulated-ZnO thin film samples taken under UV light and high vacuum. We show that the dominant mechanism of photoresponse in ZnO is the adsorption/desorption of oxygen and water molecules even when the measurement is performed in high vacuum. After the encapsulation of sample surface by a thin SiO2 layer, the adsorption/desorption rates can significantly improve, and the effects of these molecules partially removed.Article Citation - WoS: 33Citation - Scopus: 33Characterization of Thin Film Li0.5la0.5ti1-Xalxo3 Electrolyte for All-Solid Li-Ion Batteries(Elsevier, 2018) Ulusoy, Seda; Gülen, Sena; Aygün, Gülnur; Özyüzer, Lütfi; Özdemir, MehtapSince addition of Al in Li0.5La0.5TiO3 has enhanced ionic conductivity in bulk materials, it is important to apply this material on all solid state thin film batteries. Because some of the good ionic conductors such as Lithium Phosphorus Oxynitride (LiPON) are sensitive to oxygen and moisture and their application is limited, so amorphous Li0.5La0.5Ti1−xAlxO3 (LLTAlO) is a most promising candidate because of its stability. In this study, the crystalline LLTAlO targets were prepared changing the amount of x content by conventional solid state reactions. Using these targets, lithium lanthanum titanium oxide (LLTO) thin film electrolytes were deposited on ITO/SLG substrates by radio frequency magnetron sputtering system in Ar atmosphere. The structural and compositional properties of targets and thin films were characterized by SEM, XRD, Raman spectroscopy and XPS. It was found that all targets are crystalline while the thin films are amorphous. To understand the effect of Al doping on ionic conductivity, electrical measurements were done at room temperature by AC impedance spectroscopy forming ITO/LLTAlO/Al structure like capacitor. Highest ionic conductivity result, 0.96 × 10−6 S·cm−1, is obtained from the nominal thin film composition of Li0.5La0.5Ti1−xAlxO3 (x = 0.05) at room temperature measurements. Heat treatment is also conducted to investigate to understand its effect on ionic conductivity and the structure of the thin films. It is found that ionic conductivity enhances with annealing. Also, temperature dependent ionic conductivity measurements from 298 K to 385 K are taken in order to evaluate activation energy for Li-ion conduction.Article Citation - WoS: 6Citation - Scopus: 10Effect of Annealing on the Density of Defects in Epitaxial Cdte (211)/Gaas(Springer, 2018) Bakali, Emine; Selamet, Yusuf; Tarhan, EnverCdTe thin films were grown on GaAs (211) wafers by molecular beam epitaxy as the buffer layer for HgCdTe infrared detector applications. We studied the effect of annealing on the density of dislocation of these CdTe thin films under varying annealing parameters such as annealing temperature, annealing duration, and number of cycles. Annealings were carried out using a homemade annealing reactor possessing a special heater element made of a Si wafer for rapid heating. The density of dislocations, which were made observable with a scanning electron microscope after etching with an Everson solution, were calculated by counting the number of dislocations per unit surface area, hence the term etch pit density (EPD). We were able to decrease EPD values by one order of magnitude after annealing. For example, the best EPD value after a 20-min annealing at 400°C was ∼ 2 × 107 cm−2 for a 1.63-μm CdTe thin film which was about 9.5 × 107 cm−2 before annealing. We also employed Raman scattering measurements to see the changes in the structural quality of the samples. From the Raman measurements, we were able to see improvements in the quality of our samples from the annealing by studying the ratio of 2LO/LO phonon mode Raman intensities. We also observed a clear decrease in the intensity of Te precipitations-related modes, indicating a decrease in the size and number of these precipitations.Article Citation - WoS: 16Citation - Scopus: 18Study of Undoped and Indium Doped Zno Thin Films Deposited by Sol Gel Method(Springer Verlag, 2018) Medjaldi, M.; Touil, O.; Boudine, B.; Zaabat, M.; Halimi, O.; Sebais, M.; Özyüzer, LütfiIn this paper, we report the effects of Indium doping concentrations (from 0 to 10wt%) on the structural, morphological, and optical properties of deposited In doped ZnO (IZO) thin films prepared by the sol–gel method through the dip coating technique. X-ray diffraction (XRD) analysis indicates that all ZnO thin films have a polycrystalline nature with a hexagonal wurtzite phase with (002) as a preferential orientation. XRD results demonstrate that the particle size of ZnO decreased with the increase in Indium concentrations. Raman scattering spectra confirmed the wurtzite phase and the presence of intrinsic defects in our samples. Energy dispersive spectroscopy (EDS) and the X-ray photoelectron spectroscopy (XPS) measurements, confirmed the presence of zinc, oxygen and indium elements which is in agreement with XPS results. The photoluminescence (PL) spectra of the films exhibit defects-related visible emission peaks, with intensities differing owing to different concentrations of zinc vacancies. UV–Vis spectrometer measurements show that all the films are highly transparent in the visible wavelength region (≥ 70%) and presented two different absorption edges at about 3.21 eV and 3.7 eV, these may be correspond to the band gap of zinc oxide and indium oxide respectively.Article Citation - WoS: 35Citation - Scopus: 38Influence of Sulfurization Temperature on Cu2znsns4 Absorber Layer on Flexible Titanium Substrates for Thin Film Solar Cells(IOP Publishing Ltd., 2018) Buldu, Dilara Gökçen; Cantaş, Ayten; Türkoğlu, Fulya; Akça, Fatime Gülşah; Meriç, Ece; Özdemir, Mehtap; Tarhan, Enver; Özyüzer, Lütfi; Aygün, GülnurIn this study, the effect of sulfurization temperature on the morphology, composition and structure of Cu2ZnSnS4 (CZTS) thin films grown on titanium (Ti) substrates has been investigated. Since Ti foils are flexible, they were preferred as a substrate. As a result of their flexibility, they allow large area manufacturing and roll-to-roll processes. To understand the effects of sulfurization temperature on the CZTS formation on Ti foils, CZTS films fabricated with various sulfurization temperatures were investigated with several analyses including x-ray diffraction (XRD), scanning electron microscopy (SEM), x-ray photoelectron spectroscopy and Raman scattering. XRD measurements showed a sharp and intense peak coming from the (112) planes of the kesterite type lattice structure (KS), which is strong evidence for good crystallinity. The surface morphologies of our thin films were investigated using SEM. Electron dispersive spectroscopy was also used for the compositional analysis of the thin films. According to these analysis, it is observed that Ti foils were suitable as substrates for the growth of CZTS thin films with desired properties and the sulfurization temperature plays a crucial role for producing good quality CZTS thin films on Ti foil substrates.Article Citation - WoS: 42Citation - Scopus: 46Importance of Cds Buffer Layer Thickness on Cu2znsns4-Based Solar Cell Efficiency(IOP Publishing Ltd., 2018) Cantaş, Ayten; Türkoğlu, Fulya; Meriç, Ece; Akça, Fatime Gülşah; Özdemir, Mehtap; Tarhan, Enver; Özyüzer, Lütfi; Özyüzer, Gülnur AygünCu2ZnSnS4 (CZTS) thin films were grown on Mo-coated soda lime glass (SLG) substrates by the sulfurization of DC magnetron-sputtered Zn, Sn and Cu metallic precursors under a sulfur atmosphere at 550 °C for 45 min. Understanding the composition and structure of the CZTS absorber layer is necessary to obtain efficient solar cells. With this aim, x-ray diffractometry, Raman spectroscopy, scanning electron microscopy, energy dispersive spectroscopy and x-ray photoelectron spectroscopy were used to investigate the CZTS absorber layers. CZTS absorber films were obtained and found to be Cu-poor and Zn-rich in composition, which are both qualities desired for efficient solar cells. CdS was used as a buffer layer and was grown by the chemical bath deposition technique. The optical properties of CdS films on SLG were searched for using a spectroscopic ellipsometer and the results revealed that the bandgap increases with film thickness increment. CZTS-based solar cells with different CdS buffer layer thicknesses were prepared using a SLG/Mo/CZTS/CdS/ZnO/AZO solar cell configuration. The influence of the CdS buffer layer thickness on the performance of the CZTS solar cells was investigated. Device analysis showed that electrical characteristics of solar cells strongly depend on the buffer layer's thickness. Highly pronounced changes in V OC, fill factor and J SC parameters, which are the main efficiency limiting factors, with changing buffer layer thicknesses were observed. Our experiments confirmed that decreasing the CdS thickness improved the efficiency of CZTS solar cells down to the lowest thickness limit.Article Citation - WoS: 13Citation - Scopus: 13Fourcross Shaped Metamaterial Filters Fabricated From High Temperature Superconducting Ybco and Au Thin Films for Terahertz Waves(IOP Publishing Ltd., 2017) Demirhan, Yasemin; Alaboz, Hakan; Nebioğlu, Mehmet Ali; Mulla, B.; Akkaya, M.; Altan, Hakan; Sabah, Cumali; Özyüzer, LütfiIn this study, we present a new, unique fourcross shaped metamaterial terahertz (THz) filter fabricated from both gold thin films and YBa2Cu3O7-δ high Tc superconducting thin films. A commercial electromagnetic simulation software, CST Microwave Studio, is used to design and optimize the metamaterial filter structures. The proposed fourcross shaped rectangular filter structure consists of periodic metallic rings where strip lines are located at the sides of the ring. Fourcross metamaterial filters are fabricated by using e-beam lithography and ion beam exhing techniques. Terahertz time-domain spectroscopy measurements validated the design predictions for both the center frequencies and bandwidths of the resonances due to the fourcross structures. The resonance switching of the transmission spectra was investigated by lowering the temperature below the critical transition temperature. This resonance switching effect is not observed in filters made up of metals. This novel fourcross rectangular resonator with a temperature-dependent resonance behavior holds great potential for active, tunable and low loss THz devices for imaging, sensing, and detection applications.