Environmental Engineering / Çevre Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4321
Browse
27 results
Search Results
Now showing 1 - 10 of 27
Article Pomza ve Nsdd-pomza ile Sabit Yataklı Kolon Reaktörde Metilen Mavisi Giderimi: Deneysel ve Modelleme Çalışması(2019) Balcı, Esin; Ökten, Hatice Eser; Genişoğlu, Mesut; Recepoğlu, Yaşar Kemal; Gören, Ayşegül YağmurNano sıfır değerlikli demir (nSDD) yüksek renk konsantrasyonlarına sahip tekstil atıksularının arıtımında ekonomik ve çevre dostu bir adsorban olarak ortaya çıkmaktadır. Ancak nSDD partikülleri sulu çözeltilerde elektrostatik etkileşimler sebebiyle kolayca topaklaşmakta ve bu da arıtma veriminin düşmesine neden olmaktadır. Dolayısıyla düşük maliyetli, doğal poröz yapıda ve ortalama 2m2/gr spesifik yüzey alanına sahip pomza, nSDD topaklaşmasını önleyici bir malzeme olarak kullanılabilir. Bu çalışmada sadece pomza ve pomzanSDD (ağırlıkça 9:1) karışımının kullanıldığı kolon reaktörde 25, 50, 75 ve 100 mg/L metilen mavisi konsantrasyonları için arıtma verimleri incelenmiştir. Pomzanın ve pomza-nSDD karışımının 100 mg/L metilen mavisi deneyindeki toplam kapasiteleri sırasıyla 2,8 ve 4,2 mg/g-adsorban olarak bulunmuştur. Özellikle düşük konsantrasyonlarda, pomza-nSDD karışımının arıtma performansını önemli ölçüde arttırdığı görülmüştür. Thomas modeli deneysel verilere uygulanmış ve modelin öngörü gücünün düşük konsantrasyonda yüksekken, yüksek konsantrasyonlarda ortalama olduğu kanısına varılmıştır.Article Citation - WoS: 15Citation - Scopus: 19Immobilization of Esterase From Bacillus Subtilis on Halloysite Nanotubes and Applications on Dibutyl Phthalate Degradation(Elsevier, 2023) Rosales, Emilio; Pazos, Marta; Sanroman, Maria Angeles; Balcı, Esin; Sofuoğlu, AysunDibutyl phthalate (DBP) is one of the listed phthalic acid esters (PAEs) known as the priority toxicants which exhibit carcinogenic and teratogenic properties and is responsible for endocrine disruption. Therefore, its removal has become a matter to tackle with. In this work, the feasibility of DBP degradation by esterase and lipase enzymes obtained from various microorganisms and the immobilization of the most effective in a clayey material were investigated. Esterase from Bacillus subtilis exhibited the highest degradation efficiency reaching a complete degradation. Its immobilization onto halloysite nanotubes (HNTs) by adsorption method was studied by response surface methodology using a central composite design face-centered. The four selected factors that affect the HNT-enzyme composite generation were: pH, adsorption time, enzyme/HNT (E/H) ratio, and adsorption temperature, and the optimal conditions were determined (pH 7, time 360 min, E/H ratio 0.2, temperature 30oC). Consequently, the activity did not significantly decrease by immobilization, and the adsorption efficiency and relative activity were determined to be 73.15% and 82.7%, respectively. Besides, the immobilization enhanced thermal and storage stability. As for enzyme reusability, after 7 continuous cycles, the composite maintained almost 75% of its initial activity. Both the free enzyme (1 mg/mL) and the composite degraded 100 mg/L DBP with 100% efficiency and several byproducts were detected. Moreover, the composite could be reused for 7 cycles keeping a remarkable catalytic activity. Overall, this study indicated that the HNT-enzyme composite may be used as an effective candidate for remediation of the environmental media contaminated with DBP and other PAEs.(c) 2023 The Author(s). Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).Article Citation - WoS: 10Citation - Scopus: 12Novel Hybrid Adsorption-Electrodialysis (aded) System for Removal of Boron From Geothermal Brine(American Chemical Society, 2022) Altınbaş, Bekir Fırat; Orak, Ceren; Ökten, Hatice Eser; Yüksel, AslıA novel hybrid adsorption-electrodialysis (AdED) system to remove environmentally harmful boron from geothermal brine was designed and effective operating parameters such as pH, voltage, and flow rate were studied. A cellulose-based adsorbent was synthesized from glycidyl methacrylate (GMA) grafted cellulose and modified with a boron selective n-methyl-d-glucamine (NMDG) group and characterized with SEM-EDX, FT-IR, and TGA analyses. Batch adsorption studies revealed that cellulose-based adsorbent showed a remarkable boron removal capacity (19.29 mg/g), a wide stable operating pH range (2-10), and an adsorption process that followed the Freundlich isotherm (R2= 0.95) and pseudo-second-order kinetics (R2= 0.99). In the hybrid AdED system, the optimum operating parameters for boron removal were found to be a pH of 10, a voltage of 10 V, a flow rate of 100 mL/min, and an adsorbent dosage of 4 g/L. The presence of the adsorbent in the hybrid system increased boron removal from real geothermal brine (containing 199 ppm boron) from 7.2% to 73.3%. The results indicate that the designed AdED system performs better than bare electrodialysis for boron removal from ion-rich real geothermal brine while utilizing environmentally friendly cellulose-based adsorbent.Article Citation - WoS: 4Citation - Scopus: 5Continuous Treatment of Diethyl Hexyl and Dibutyl Phthalates by Fixed-Bed Reactor: Comparison of Two Esterase Bionanocomposites(Elsevier, 2022) Sanroman, Maria Angeles; Balcı, Esin; Rosales, Emilio; Pazos, Marta; Sofuoğlu, AysunThe removal of Diethyl hexyl phthalate (DEHP) and Dibutyl phthalate (DBP) is of great importance due to their potential adverse effects on the environment and human health. In this study, two bionanocomposites prepared by immobilization of Bacillus subtilis esterase by crosslinking to halloysite and supported in chitosan and alginate beads were studied and proposed as a green approach. The esterase immobilization was confirmed by physical-chemical characterization. Bionanocomposite using chitosan showed the best degradation levels in batch tests attaining complete degradation of DBP and around 90% of DEHP. To determine the operational stability and efficiency of the system, two fixed bed reactors filled with both bionanocomposites were carried out operating in continuous mode. Chitosan based bionanocomposite showed the best performance being able to completely remove DBP and more than 85% of DEHP at the different flowrates. These results proved the potential of these synthesized bionanocomposites to effectively remove Phthalic Acid Esters.Article Citation - WoS: 31Citation - Scopus: 35Electrochemical Degradation of Methylene Blue by a Flexible Graphite Electrode: Techno-Economic Evaluation(American Chemical Society, 2022) Gören, Ayşegül Yağmur; Recepoğlu, Yaşar Kemal; Edebali, Özge; Şahin, Çağrı; Genişoğlu, Mesut; Ökten, Hatice EserIn this study, electrochemical removal of methylene blue (MB) from water using commercially available and low-cost flexible graphite was investigated. The operating conditions such as initial dye concentration, initial solution pH, electrolyte dose, electrical potential, and operating time were investigated. The Box-Behnken experimental design (BBD) was used to optimize the system's performance with the minimum number of tests possible, as well as to examine the independent variables' impact on the removal efficiency, energy consumption, operating cost, and effluent MB concentration. The electrical potential and electrolyte dosage both improved the MB removal efficiency, since increased electrical potential facilitated production of oxidizing agents and increase in electrolyte dosage translated into an increase in electrical current transfer. As expected, MB removal efficiency increased with longer operational periods. The combined effects of operating time-electrical potential and electrical potential-electrolyte concentration improved the MB removal efficiency. The maximum removal efficiency (99.9%) and lowest operating cost (0.012 $/m3) were obtained for initial pH 4, initial MB concentration 26.5 mg/L, electrolyte concentration 0.6 g/L, electrical potential 3 V, and operating time 30 min. The reaction kinetics was maximum for pH 5, and as the pH increased the reaction rates decreased. Consequent techno-economic assessment showed that electrochemical removal of MB using low-cost and versatile flexible graphite had a competitive advantage.Article Citation - Scopus: 22Multi‑purpose Reverse Logistics Network Design for Medical Waste Management in a Megacity: Istanbul, Turkey(Springer, 2022) Balcı, Esin; Balcı, Sezin; Sofuoğlu, AysunIn the study, a multi-purpose reverse logistics network has been designed to create effectual management of medical waste (MW) generated in 39 districts of Istanbul, a heavily populated city, during the COVID-19 pandemic as well as that to be generated in the next decade. With the model, the medical waste management system in Istanbul is analyzed during the pandemic and for the next 10 years. The model attempts to integrate economic, environmental, and social objectives within the sustainable development goals. It aims to maximize the number of personnel and government earnings for the estimated MW of a megacity while minimizing the total fixed cost and the cost of carbon emissions and transportation. The results indicated that the existing facilities are sufficient for the treatment and disposal of MW generated even under pandemic conditions. However, the capacity of the sterilization facility could be insufficient to treat the estimated amount of MW in the next decade. Opening a sterilization facility near the sanitary landfill in Komurcuoda with a total management cost of 62,450,332 €/year would be an optimum solution for Istanbul MW. In comparison to the single-purpose model results, the multi-purpose model resulted in approximately 42,000 € more in total cost. Sensitivity analyses show that the amount of MW has the most significant effect on the total cost. This simple model created an effective MW management proposal for Istanbul, which can be a model for megacities.Article Citation - WoS: 40Citation - Scopus: 47Boron in Geothermal Energy: Sources, Environmental Impacts, and Management in Geothermal Fluid(Elsevier, 2022) Mott, A.; Baba, Alper; Hadi Mosleh, Mojgan; Ökten, Hatice Eser; Babaei, Masoud; Gören, Ayşegül Yağmur; Feng, C.; Recepoğlu, Yaşar Kemal; Uzelli, Taygun; Uytun, Hüseyin; Morata, Diego; Yüksel Özşen, AslıThe problem of hazardous chemicals in geothermal fluid is a critical environmental concern in geothermal energy developments. Boron is among the hazardous contaminants reported to be present at high concentrations in geothermal fluids in various countries. Poor management and inadequate treatment of geothermal fluids can release excessive boron to the environment that has toxic effects on plants, humans, and animals. Despite the importance of boron management in geothermal fluid, limited and fragmented resources exist that provide a comprehensive understanding of its sources, transport and fate, and the treatment strategies in geothermal energy context. This paper presents the first critical review from a systematic and comprehensive review on different aspects of boron in geothermal fluid including its generation, sources, toxicity, ranges and the management approaches and treatment technologies. Our research highlights the origin of boron in geothermal water to be mainly from historical water-rock interactions and magmatic intrusion. Excessive concentrations of boron in geothermal fluids have been reported (over 500 mg/L in some case studies). Our review indicated that possible boron contamination in geothermal sites are mostly due to flawed construction of production/re-injection wells and uncontrolled discharge of geothermal water to surface water. The dominancy of non-ionic H3BO3 species makes the selection of the suitable treatment method for geothermal waters limited. Combining boron selective resins and membrane technologies, hybrid systems have provided effluents suitable for irrigation. However, their high energy consumption and course structure of boron selective resins encourage further research to develop cost-effective and environmentally friendly alternatives.Article Citation - WoS: 42Citation - Scopus: 44Boron Carbon Nitride Nanosheets in Water and Wastewater Treatment: a Critical Review(Elsevier, 2022) Recepoğlu, Yaşar Kemal; Gören, Ayşegül Yağmur; Vatanpour, Vahid; Yoon, Yeojoon; Khataee, AlirezaThe availability and accessibility of clean and secure water supplies are pressing technological and scientific issues worldwide. As a result of global water constraints, wastewater treatment and reuse are being evaluated as feasible alternatives to fresh water for agricultural irrigation and domestic and industrial purposes. Boron carbon nitride (BCN) nanosheets have been studied intensively in the last decade in batteries, biosensors, and capacitors, and for use as catalysts, and they have recently been used in wastewater treatment. BCN materials, along with their synthesis processes, characteristics, and application areas in water and wastewater treatment, are discussed thoroughly in this paper. Additionally, synthesis processes for ternary BCN compounds, including chemical vapor deposition, ion beam-aided deposition, magnetron sputtering, and pulsed laser deposition, are described. BCN materials have also been explored because of their flexible electrical features, excellent mechanical strength, outstanding unreactivity, and significant stability, which make them appropriate for a range of severe environment applications. Thus, the use of BCN materials as photocatalysts and adsorbents and in electrochemical reduction and capacitive deionization are also discussed thoroughly. The highest ammonia production of 172,226.5 μg/h.mg.cat and faradic efficiency of 95.3% have been obtained using the BCN@Cu/CNT catalyst, whereas the ammonia production and FE values for metal-free BCN are 7.75 μg/h.mg.cat and 13.8%. Moreover, the maximum attained adsorption capacities of BCN nanosheets for Pb2+ and Hg2+ are 210 and 625 mg/g, respectively. Overall, this review indicates that essential work on BCN nanosheets is still needed. Future research should focus on the development of BCN nanostructures to encourage multidisciplinary research.Article Citation - WoS: 21Citation - Scopus: 24Phytoremediation of Olive Mill Wastewater With Vetiveria Zizanioides (l.) Nash and Cyperus Alternifolius L.(Elsevier, 2021) Gören, Ayşegül Yağmur; Yücel, Arzu; Sofuoğlu, Sait Cemil; Sofuoğlu, AysunOlive Mill Wastewater (OMW) contains high concentrations of contaminants, including organic, nitrogen, and phenolic compounds that are extremely harmful to the environment and human health. The key purpose of this study was to remove total organic carbon (TOC), total nitrogen (TN), and phenolic compounds (TP) from OMW using floating wetland planted with Vetiveria zizanioides (L.) Nash (vetiver) and Cyperus alternifolius L. (umbrella palm) species. A total of eighteen floating wetlands were constructed. Twelve tanks were planted with vetiver and umbrella palm while another six tanks were maintained as unplanted controls. Experiments were conducted with wastewater volume of 56 L for 67 days using 5% (OMW-5) and 15% (OMW-15) treatments of OMW in a greenhouse. The highest TOC, TN, and TP removal efficiencies were found to be 95.3 ± 0.01, 82.7 ± 2.55, and 98.8 ± 0.07% in umbrella palm planted OMW-5, while the removal efficiencies were 84.9 ± 0.38, 92.7 ± 0.37, and 38.9 ± 1.97% in vetiver planted OMW-5. Similarly, the TOC, TN, and TP removal efficiencies in OMW-15 were 89.3 ± 0.28, 40.86 ± 1.73, and 96.8 ± 0.18% with umbrella palm and 89.1 ± 0.70, 23.7 ± 1.27, and 92.1 ± 0.41% with vetiver. The plants accumulated trace elements, especially in the roots, with the order of Fe > Mn > Cu > Zn > B > Pb > Cr > Ni > Co > Cd for umbrella palm. The umbrella palm shoot phenol content was found to be 2358 ± 201 and 1421 ± 198 mg/kg in OMW-5 and OMW-15, respectively. Overall, this study revealed that floating wetlands planted with vetiver and umbrella palm species have the potential to be used as a green treatment method to treat diluted high strength OMW.Article Citation - WoS: 12Citation - Scopus: 13Selected Persistent Organic Pollutants in Ambient Air in Turkey: Regional Sources and Controlling Factors(American Chemical Society, 2021) Güngörmüş, Elif; Sofuoğlu, Aysun; Çelik, Halil; Gedik, Kadir; Mulder, Marie D.; Lammel, Gerhard; Sofuoğlu, Sait CemilAs a result of its unique location, Turkey receives air masses from Europe, Russia, Middle East, and Africa, making it an important place in terms of long-range atmospheric transport (LRT) of contaminants. Atmospheric levels of 22 organochlorine pesticides (OCPs), 45 polychlorinated biphenyls (PCBs), and 14 polybrominated diphenyl ethers (PBDEs) were measured in two metropolitan cities, Istanbul and Izmir, on a weekly basis from May 2014 to May 2015. Dichlorodiphenyltrichloroethane (DDT) and its derivatives were dominant OCP species, followed by isomers of hexachlorocyclohexane (HCH) at both sites. The annual mean concentration of Sigma DDX (sum of o,p'-DDT, p,p'-DDT, o,p'-DDD, p,p'-DDD, o,p'-DDE, and p,p'-DDE) was 82 pg/m(3) for Istanbul and 89 pg/m(3) for Izmir, while these levels were about 46 pg/m(3) for Sigma HCHs (sum of alpha-, beta-, gamma-, and delta-HCH) at both of the sites. At both stations, tri- and tetra-PCBs and tetra- and penta-PBDEs were dominant congeners. The temperature dependence indicates that both LRT and local contaminated areas contribute to the elevated levels. A Lagrangian particle dispersion model (FLEXPART) showed a few potential source regions in northern Africa and Middle East, southern-southwestern and eastern Europe including Russia, as well as from local domestic metropolitan areas.
- «
- 1 (current)
- 2
- 3
- »