IZTECH Research Centers Collection / İYTE Araştırma Merkezleri Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/11147/2636
Browse
18 results
Filters
Settings
Search Results
Article Citation - WoS: 4Citation - Scopus: 5Breakthrough Curve Analysis of Phosphorylated Hazelnut Shell Waste in Column Operation for Continuous Harvesting of Lithium From Water(Elsevier, 2024) Recepoğlu, Yaşar Kemal; Arar, Ozguer; Yuksel, AsliIn batch-scale operations, biosorption employing phosphorylated hazelnut shell waste (FHS) revealed excellent lithium removal and recovery efficiency. Scaling up and implementing packed bed column systems necessitates further design and performance optimization. Lithium biosorption via FHS was investigated utilizing a continuous-flow packed-bed column operated under various flow rates and bed heights to remove Li to ultra-low levels and recover it. The Li biosorption capacity of the FHS column was unaffected by the bed height, however, when the flow rate was increased, the capacity of the FHS column decreased. The breakthrough time, exhaustion time, and uptake capacity of the column bed increased with increasing column bed height, whereas they decreased with increasing influent flow rate. At flow rates of 0.25, 0.5, and 1.0 mL/min, bed volumes (BVs, mL solution/mL biosorbent) at the breakthrough point were found to be 477, 369, and 347, respectively, with the required BVs for total saturation point of 941, 911, and 829, while the total capacity was calculated as 22.29, 20.07, and 17.69 mg Li/g sorbent. In the 1.0, 1.5, and 2.0 cm height columns filled with FHS, the breakthrough times were 282, 366, and 433 min, respectively, whereas the periods required for saturation were 781, 897, and 1033 min. The three conventional breakthrough models of the Thomas, Yoon-Nelson, and Modified Dose-Response (MDR) were used to properly estimate the whole breakthrough behavior of the FHS column and the characteristic model parameters. Li's extremely favorable separation utilizing FHS was evidenced by the steep S-shape of the breakthrough curves for both parameters flow rate and bed height. The reusability of FHS was demonstrated by operating the packed bed column in multi-cycle mode, with no appreciable loss in column performance.Article Citation - WoS: 5Citation - Scopus: 5Are Soil and Geology Characteristics Considered in Urban Planning? an Empirical Study in Izmir (turkiye)(MDPI, 2023) Salata, Stefano; Uzelli, TaygunIt is well acknowledged that sustainable soil management can play a crucial role in reducing the vulnerability of urban areas, but are soil characteristics properly evaluated in the decision-making process concerning urbanization? Within this work, we conducted an analysis of the land-use change trends in the city of Izmir (Turkey). We made an extended and detailed analysis of the urbanization processes between 2012 and 2018 in a geographic information system environment (Esri ArcGIS 10.8.1 and ArcGIS Pro 3.0). Then, we superimposed by spatial overlay different soil characteristics: land capability, hydraulic conductibility, soil groups, and fault lines. We discovered that although there is a joint agreement on soil and its geological importance in reducing urban vulnerabilities to flooding, urban heat islands, agricultural production, or earthquakes, there is scarce knowledge of its characteristics to inform land-use planning. This work sheds some light on how newly developed areas are planned without proper consideration of soil properties, following a fuzzy and irrational logic in their distribution. Results encourage the utilization and inclusion of soil knowledge to support the decision-making process concerning urban transformation to achieve more resilient and less vulnerable urban systems.Article Citation - WoS: 8Citation - Scopus: 8Structural Controls and Hydrogeochemical Properties of Geothermal Fields in the Varto(TÜBİTAK Scientific & Technological Research Council Turkey, 2021) Uzelli, Taygun; Sener, Mehmet Furkan; Dolek, Iskender; Baba, Alper; Sozbilir, Hasan; Dirik, Ramazan KadirVarto and the surrounding region have important geothermal fields, developing in strike-slip tectonic setting in East Anatolia, which resulted from the collision of the Arabian and Eurasian plates. The main structural elements in the area are the NE-trending sinistral and NW-trending dextral strike-slip fault segments and N-S trending extension zones. In order to determine fault-controlled geothermal circulation, it is very important to fully characterize the structural elements in these complex environments. The widely distributed volcanic rocks have fracture and crack systems that play an important role in surface infiltration, geothermal fluid, and groundwater circulation. Especially in areas where the fault segments intersect, hot springs outlets and natural resources easily come to the surface. In order to understand the flow paths of geothermal fluid along the faults in these geothermal systems, it is necessary to determine the stress state of the faults and to map the distribution of the structural elements. For this reason, we conducted a detailed study on the Varto Fault Zone, which has important geothermal fields in Eastern Anatolia. We present conceptual models of the geothermal fields in the Varto region that show favorable geothermal activity on the intersecting fault segments, fault bends, step-overs, and accompanying fracture-crack sets. As a result, we emphasize that the planes of strike-slip faults in transtensional areas are more favorable for secondary permeability and enhances the geothermal fluid circulation, and this can be supported by hydrogeochemical data.Article Citation - WoS: 4Citation - Scopus: 15Effects of Seismic Activity on Groundwater Level and Geothermal Systems in İzmir, Western Anatolia, Turkey: the Case Study From October 30, 2020 Samos Earthquake(TÜBİTAK - Türkiye Bilimsel ve Teknolojik Araştırma Kurumu, 2021) Uzelli, Taygun; Bilgiç, Esra; Öztürk, Bahadır; Baba, Alper; Sözbilir, Hasan; Tatar, OrhanThe October 30, 2020 Samos earthquake (Mw 6.6) affected the Aegean Sea and environs, caused destruction and loss of life in the city of İzmir located 70 km away from the earthquake epicenter. Before this earthquake, water resources were monitored in the areas of Bayraklı, Gülbahçe, and Seferihisar. For this purpose, 10 groundwater monitoring wells were drilled in the Bayraklı area, where groundwater level, temperature, and electrical conductivity changes were monitored at 1-h intervals in 5 wells. Besides physical parameters such as groundwater levels, temperatures and electrical conductivities, hydrogeochemical cations, and anions measured in the study area. Change in the groundwater levels was observed before, during, and after the Samos earthquake. A trend of rising groundwater level was observed two days before the mainshock, to a height of 10 cm, and the level was maintained till the end of the earthquake. The water levels returned to its original height after about 7 to 10 days of the earthquake. Moreover, electrical conductivity (EC) values were changed because of the interaction with the surrounding rocks and well walls, mixing with different waters during the earthquake shaking. The essential anomalies were observed in the geothermal fields of Gülbahçe and Seferihisar. Due to this earthquake, new geothermal springs emerged along the NE-SW trending Gülbahçe and Tuzla faults, located about 50 to 20 km from the Samos earthquake epicenter, respectively. The new geothermal waters are in Na-Cl composition and similar to other geothermal springs in the region. While the recorded water temperatures in the new geothermal springs vary from 40 to 45 °C in Seferihisar, it was measured between 35 and 40 °C in Gülbahçe. Due to these anomalies, it is found essential to monitor the effect of the earthquake on the physical and chemical characteristics of the groundwater and its usefulness in earthquake predictions.Article Citation - WoS: 4Citation - Scopus: 10Characterization of Sb Scaling and Fluids in Saline Geothermal Power Plants: a Case Study for Germencik Region (büyük Menderes Graben, Turkey)(Pergamon-Elsevier Science Ltd, 2021) Tonkul, Serhat; Baba, Alper; Demir, Mustafa M.; Regenspurg, SimonaTurkey is located on the seismically active Alpine-Himalayan belt. Although tectonic activity causes seismicity in the Anatolian plate, it also constitutes an important geothermal energy resource. Today, geothermal energy production is heavily concentrated in Turkey's Western Anatolia region. Graben systems in this region are very suitable for geothermal resources. The Buyuk Menderes Graben (BMG) is an area of complex geology with active tectonics and high geothermal potential power. Germencik (Aydin) is located in the BMG, where the geothermal waters include mainly Na-Cl-HCO3 water types. This study examined the stibnite scaling formed in the preheater system of the Germencik Geothermal Field (GGF). The formation of the stibnite scaling on the preheater system dramatically reduces the energy harvesting of the GGF. Considering the stibnite scaling in the surface equipment, the optimum reinjection temperature was determined as 95 degrees C to prevent stibnite scaling in the GGF.Article Citation - WoS: 11Citation - Scopus: 11Cfd Characteristics of Refrigerated Trailers and Improvement of Airflow for Preserving Perishable Foods(MDPI, 2019) Yildiz,T.When preserving perishable goods, maintaining a constant temperature over the cold supply chain is essential. Therefore, refrigerated vehicles are an important part of the cold supply chain system. However, many traditional refrigerated cargo systems are not designed to support the homogeneity of the temperature inside cargo trailers. Indeed, refrigerating equipment is usually placed on one side of transportation systems as this is considered to be more practical. Such a configuration thus leads to significant temperature differences in the two distinct parts of a refrigerated cargo trailer, which might affect the quality, safety, and shelf life of perishable foods. This research aims to improve the temperature distribution of refrigerated trailers. In this study, it is highlighted that in the most commonly used traditional refrigerated trailer models, lower air velocity and higher product temperature are observed at the rear. There is also a partial product chilling risk at the front of the refrigerated trailer. This study investigates and reports significant differences among the three airflow design models of refrigerated cargo systems by applying turbulence flow, heat, and mass transfer models. The analyses of these three models reveal that significant improvement could be achieved by applying the proper arrangements of inlets on the ceiling of the trailer body. © 2019 by the author.Article Citation - WoS: 11Citation - Scopus: 17Design and Analysis of a Lightweight Composite Shipping Container Made of Carbon Fiber Laminates(MDPI, 2019) Yildiz,T.The literature indicates that a 20% reduction in the weight of empty 40-foot shipping containers would result in $28 billion of fuel savings, along with a 3.6 exajoule reduction in the energy demand over containers’ 15-year lifetime. Decreasing the energy demand and thereby greenhouse gas emissions by utilizing lightweight shipping containers has been an unexplored strategy. In this regard, this study investigates the possibility of further reducing the weight of an empty container without compromising the structural integrity, strength, and function of a traditional steel container. This research finds that up to an 80% reduction in weight is possible by producing shipping containers with composite materials. This research presents the new design of a 40-foot container made of carbon fiber laminates. The tare weight of a traditional 40-foot shipping container is around 3750 kg. On the contrary, in this research, the weight of a composite design of the same container is calculated to be around 822 kg. Additional tests with various loads, such as lifting the container and stacking loads onto the composite container, are performed to explore the strength and buckling issues of the design presented in this study. The analyses reveal that the composite shipping container is a highly promising candidate for reducing greenhouse gas emissions, providing fuel savings and thus reducing the operational costs of transportation. © 2019 by the author.Article Citation - WoS: 55Citation - Scopus: 67Desalination: From Ancient To Present and Future(MDPI, 2021) Angelakis, Andreas N.; Valipour, Mohammad; Choo, Kwang-Ho; Ahmed, Abdelkader T.; Baba, Alper; Kumar, Rohitashw; Toor, Gurpal S.Water is life, and without water, there would be no civilizations and a vacant Earth. Water is considered an abundant natural resource on the earth. Water covers 3/4 of the surface. However, 97% of the available water on the earth is salty oceanic water, and only a tiny fraction (3%) is freshwater. This small portion of the available water supplies the needs of humans and animals. However, freshwater exists in underground, rivers, and lakes and is insufficient to cover all the world's water demands. Thus, water saving, water reuse, rainwater harvesting, stormwater utilization, and desalination are critical for maintaining water supplies for the future of humanity. Desalination has a long history spanning centuries from ancient times to the present. In the last two decades, desalination has been rapidly expanding to meet water needs in stressed water regions of the world. Yet, there are still some problems with its implementation in several areas of the world. This review provides a comprehensive assessment of the history of desalination for wiser and smarter water extraction and uses to sustain and support the water needs of the earth's inhabitants.Article Citation - WoS: 1Citation - Scopus: 1Groundwater Recharge Estiaton in the Alaşehir Sub-Basin Using Hydro-Geochemical Data; Alaşehir Case Study(Springer, 2021) Tonkul, Serhat; Baba, Alper; Şimşek, Celalettin; Demirkesen, Ali CanThe issue of groundwater recharge has gained importance in countries where there is not enough water supply to the aquifer. However, groundwater recharge is a difficult parameter to determine. This difficulty stems from factors such as the location of the area to be studied, time, cost, and hydrological data. Numerical, isotope, and chemical approaches are used in groundwater recharge investigations. Numerical and chemical approaches are more costly and time-consuming than chemical approaches. This study aims to ascertain alluvial aquifer recharge in Alaehir (Manisa) sub-basin using chemical approaches (Chloride Mass Balance Method) and its applicability. For this purpose, research wells were drilled at 25 different points in the alluvial aquifer, water sampling was done in wet and dry periods, and rainwater water samples were collected. Groundwater recharge was calculated by using chemical approaches from the chloride concentrations of the water samples collected. An annual average of 74.84 mm of recharge was found in the Alaehir sub-basin. This value corresponds to 16.38% of annual rainfall. At the same time, it was examined the groundwater and geothermal mixing mechanism to demonstrate the applicability of the Chloride Mass Balance Method. It was concluded that geothermal fluid in Alaehir sub-basin mixed with groundwater at a rate of 17%.Article Citation - WoS: 5Citation - Scopus: 7Effect of High Salinity and Temperature on Water-Volcanic Rock Interaction(Springer, 2021) Gören, Ayşegül Yağmur; Gören, Ayşegül Yağmur; Topçu, Gökhan; Demir, Mustafa Muammer; Demir, Mustafa M.; Baba, Alper; Baba, AlperIn order to understand the processes occurring in natural hydrothermal systems, it was carried out a series of water-volcanic rock interaction studies in the laboratory and an intermediate volcanic rock samples from geothermal production wells in Tuzla geothermal field (TGF) in western Turkey. A high-pressure autoclave was used to conduct water-rock interaction experiments under similar conditions of the field. Rainwater and seawater were treated with volcanic rocks at 140 degrees C (reservoir temperature) and 4.5 bar pressure. The change in the ionic content of the resulting fluids was examined in terms of the type of volcanic rocks and mineral saturation index. The results indicate that talc and diopside minerals in geothermal systems may cause scaling at high temperatures depending on the geothermal fluid and pH.