Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
3 results
Search Results
Article Citation - WoS: 4Citation - Scopus: 5Effects of Tib2 Nanoparticle Content on the Microstructure and Mechanical Properties of Aluminum Matrix Nanocomposites(Walter de Gruyter GmbH, 2017) Kandemir, SinanThe present work reports the fabrication of A357 alloy matrix nanocomposites reinforced with 0.5, 1.0 and 2.0 wt.-% TiB2 nanoparticles (20-30 nm) by a novel method which is the combination of semi-solid mechanical mixing and ultrasonic dispersion of nanoparticles in liquid state. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicated that reasonably effective deagglomeration and uniform distribution of TiB2 nanoparticles into the matrix were achieved. Transmission electron microscopy studies also confirmed that the nanoparticles were embedded into the matrix and a good bonding was obtained between the matrix and the reinforcement. Increasing nanoparticle content led to grain refinement and significant enhancement in the mechanical properties of nanocomposites. The addition of 0.5, 1.0, and 2.0 wt.-% TiB2 nanoparticles increased the 0.2 % proof stress of matrix alloy by approximately 31, 48 and 61 %, respectively. The contribution of different mechanisms to the strength enhancement is discussed. It is proposed that the strengthening is mainly due to Orowan mechanism and dislocation generation effect by the coefficient of thermal expansion mismatch between the TiB2 nanoparticles and the matrix.Article Citation - WoS: 11Citation - Scopus: 12Electrical Properties of Gadolinia Doped Ceria Electrolytes Fabricated by Infiltration Aided Sintering(Elsevier Ltd., 2019) Sındıraç, Can; Büyükaksoy, Aligül; Akkurt, SedatCommon solid oxide fuel cell (SOFC) electrolyte materials (e.g., gadolinia doped ceria - GDC) demand temperatures exceeding 1400 degrees C for densification by conventional solid state sintering. It is very desirable to reduce the densification of the SOFC electroltytes to i) avoid microstructural coarsening of the composite anode layers, which are co-sintered with the electolyte layer in the anode supported SOFC fabrication scheme and ii) reduce energy consumption during SOFC manufacturing. We have recently demostrated a novel infiltration-aided sintering route to densify GDC ceramics at 1200 degrees C. In the present work, we present the electrical properties of GDC ceramics fabricated thusly. Comparison of high density (>= 95%) samples fabricated by conventional or infiltration-aided sintering reveal that at 700 degrees C, similar total electrical conductivities are obtained, while at 300 degrees C, specific grain boundary resistivity is smaller in the latter. Bulk (grain) conductivity is higher in porous GDC ceramics (relative density <= 90%) fabricated by infiltration-aided sintering than the conventionally sintered ones with similar porosities. Finally, open circuit voltage of 0.84 V at 700 degrees C, obtained under dilute hydrogen and stagnant air conditions suggests that GDC ceramics densified by infiltration-aided sintering are suitable for use as SOFC electrolytes.Conference Object Development of Graphene Nanoplatelets Reinforced Aluminium Matrix Nanocomposites by a Combination of Semi-Solid Stirring and Ultrasonic Treatment(European Conference on Composite Materials, 2016) Kandemir, Sinan; Aydoğan, YücelGraphene Nanoplatelets (GNPs) consisting of graphene layers with a thickness less than 100 nm have recently emerged as a promising reinforcement type owing to their excellent physical and mechanical properties to improve mechanical properties of alloys beyond ceramic nanoparticles. Although there are numerous studies on GNPs reinforced polymer matrix composites in the literature, the number of studies related to the incorporation of GNPs in metal matrices is limited. It is a challenging task to incorporate and uniformly distribute GNPs into liquid metals due to their poor wettability and large surface-to-volume ratio. The purpose of this study is to effectively disperse GNPs into liquid aluminium. 0.5 wt.% GNPs with an average thickness of 50-100 nm and size of 5 ?m were first incorporated into A360 aluminium alloy under semi-solid stirring, and then the composite was ultrasonically treated in fully liquid state. The microstructural investigation of the nanocomposites by optical and scanning electron microscopy may suggest that relatively uniform distribution and effective deagglomeration of GNPs in the matrix were achieved. The hardness of the GNPs reinforced nanocomposites increased in comparison with that of semi-solid stirred and ultrasonically processed A360 alloy without reinforcement, indicating the potential of GNPs for strengthening metals. © 2016, European Conference on Composite Materials, ECCM. All rights reserved.