Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
24 results
Search Results
Conference Object Kinematic Design of a Novel Finger Exoskeleton Mechanism for Rehabilitation Exercises(Springer international Publishing Ag, 2024) Kiper, Gokhan; Inanc, EmirhanThe paper presents the kinematic design of a novel low-cost two degree-of-freedom finger exoskeleton mechanism to be used for rehabilitation exercises for post-stroke or injured patients. The first degree-of freedom is for the flexion/extension of metacarpophalangeal joint and is achieved via a planar 4-bar loop. The second degree-of-freedom is for the simultaneous flexion/extension of distal/proximal interphalangeal joints and is achieved via an over-constrained double-spherical 6-bar linkage, where 3 of the links are the phalanges of the finger and 2 of the joints are finger joints themselves. So, the number of extra links are less compared to other designs in the literature. The motion of an index finger is recorded via image processing. The four-bar mechanism part is designed for optimum transmission angle characteristics. The formulation and application of the kinematic synthesis of the 6-bar linkage is presented. The design is verified via a prototype.Conference Object Determination of Interfacial Heat Transfer Coefficient for a Mixed Convection Heat Transfer in a Vertical Channel Filled With Uniformly Heated Blocks(Begell House Inc., 2015) Çelik, Hasan; Mobedi, Moghtada; Manca,O.; Buonomo,B.The interfacial convective heat transfer coefficient of a periodic porous medium under mixed convection heat transfer is determined computationally by using volume averaging method. The porous medium consists of square blocks in inline arrangement. The continuity, momentum and energy equations are solved in dimensionless form for a representative elementary volume of porous medium and the velocity and temperature fields for different values of Richardson and Reynolds numbers are obtained. Based on the obtained results, the interfacial convective heat transfer coefficient is calculated by using volume average method. The temperature of the solid phase is considered uniform and different than the inlet temperature. A detailed discussion on the effect of the governing dimensionless parameters (i.e. Reynolds, Richardson numbers, and porosity) on the local and average interfacial Nusselt number is done. It is concluded that the local interfacial convective heat transfer coefficient increases with Reynolds number, however the rate of increase depends on Richardson number and porosity. The study is performed for two values of porosity of 0.51 and 0.94. © 2021, Begell House Inc. All rights reserved.Conference Object A Numerical Study on the Determination of the Effects of Pore To Throat Size Ratio on the Thermal Dispersion in Porous Media(Begell House, 2014) Özgümüş, Türküler; Mobedi, Moghtada; Özkol, ÜnverDirect pore-level numerical simulations are widely used to estimate macroscopic properties of fluid flow and heat transfer in porous media. Thermal dispersion is one of the most important macroscopic transport parameters for analyzing convective heat transfer in a porous medium. It should be known in order to predict the macroscopic temperature distribution. In the present study, a microscopic scale analysis is performed for a porous medium with periodic structure. A representative elementary volume is chosen from an infinite medium consists of rectangular rods in inline arrangement. The continuity and momentum equations are solved to obtain flow field and the energy equations for fluid and solid phases are solved to obtain microscopic temperature distributions in two phases. There are velocity and temperature deviations between macroscopic and microscopic local values. Volume averaging method is applied to the computed deviations and thermal dispersion conductivity of porous media is determined. The aim of this study is to analyze the effects of pore to throat size ratio on the longitudinal and transverse thermal dispersion in porous media. The study is performed for representative elementary volumes with different pore to throat size ratios and Reynolds numbers from 1 to 100. The study is performed for high porosity porous media (ε = 0.7 and 0.91). It is shown that the porosity and pore to throat size ratio have more influence on the transverse rather than longitudinal thermal dispersion. © 2014, Begell House Inc. All rights reserved.Book Part Citation - WoS: 1Citation - Scopus: 1A Historical Review of Polyhedral Linkages(Springer, 2024) Kiper, GökhanPolyhedral linkages are linkages that resemble polyhedral shapes at different configurations. This paper summarizes the necessary geometrical fundamentals of polyhedral geometry and presents a historical and critical review of the polyhedral linkage designs available in the literature. Basic definitions of polyhedral geometry and operations are needed to comprehend and design polyhedral linkages. First, early works on polyhedral linkages are presented, where flexible polyhedra with rigid faces and flexible edges are issued. The final part is reserved to conformal polyhedral linkages, which go through shape transformations while plane, dihedral and solid angles are preserved. Conformal polyhedral linkages are examined in four categories: 1) Jitterbug-like linkages with screwing polygonal links connected to each other with dihedral angle preserving links, 2) polyhedral linkages with planar kinematic chains in radial motion planes, 3) polyhedral linkages with planar kinematic chains on faces, that are connected to each other with dihedral angle preserving links, and 4) other conformal polyhedral linkages. © The Author(s), under exclusive license to Springer Nature Switzerland AG 2024.Article Citation - WoS: 2Citation - Scopus: 3Design and Manufacturing of a Hip Joint Motion Simulator With a Novel Modular Design Approach(Springer, 2024) Torabnia, S.; Mihçin, D.Ş.; Lazoglu, I.The study is aimed to develop a hip joint wear simulator using a modular design approach to help experimentally monitor and control critical wear parameters to validate in-silico wear models. The proper control and application of wear parameters such as the range of motion, and the applied force values while estimating the lost material due to wear are essential for thorough analysis of wear phenomena for artificial joints. The simulator's dynamics were first modeled, then dynamic loading data was used to calculate the forces, which were further used for topology optimization to reduce the forces acting on each joint. The reduction of the link weights, connected to the actuators, intends to improve the quality of motion transferred to the femoral head. The modular design approach enables topology-optimized geometry, associated gravitational and dynamic forces, resulting in a cost-effective, energy-efficient product. Moreover, this design allows integration of the subject specific data by allowing different boundary conditions following the requirements of industry 5.0. Overall, the in-vitro motion stimulations of the hip-joint prosthesis and the modular design approach used in the study might help improve the accuracy and the effectiveness of wear simulations, which could lead into the development of better and longer-lasting joint prostheses for all. The subject-specific and society-based daily life data implemented as boundary conditions enable inclusion of the personalized effects. Next, with the results of the simulator, CEN Workshop Agreement (CWA) application is intended to cover the personalized effects for previously excluded populations, providing solution to inclusive design for all. © 2023, The Author(s), under exclusive licence to Springer-Verlag France SAS, part of Springer Nature.Article Citation - WoS: 9Citation - Scopus: 11Experimental Investigation of Spray Characteristics of Ethyl Esters in a Constant Volume Chamber(Springer, 2024) Ulu, A.; Yildiz, G.; Özkol, Ü.; Rodriguez, A.D.Abstract: Biodiesels are mainly produced via the utilization of methanol in transesterification, which is the widespread biodiesel production process. The majority of this methanol is currently obtained from fossil resources, i.e. coal and natural gas. However, in contrast with methanol, biomass-based ethanol can also be used to produce biodiesels; this could allow the production line to become fully renewable. This study aimed to investigate the spray characteristics of various ethyl ester type biodiesels derived from sunflower and corn oils in comparison to methyl esters based on the same feedstocks and reference petroleum-based diesel. Spray penetration length (SPL) and spray cone angle (SCA) were experimentally evaluated in a constant volume chamber allowing optical access, under chamber pressures of 0, 5, 10 and 15 bar and injection pressures of 600 and 800 bar. Sauter mean diameter (SMD) values were estimated by using an analytical correlation. Consequently, ethyl esters performed longer SPL (2.8–20%) and narrower SCA (5.1–19%) than diesel under ambient pressures of 5 and 10 bar. Although the SMD values of ethyl esters were 48% higher than diesel on average, their macroscopic spray characteristics were very similar to those of diesel under 15 bar chamber pressure. Moreover, ethyl esters were found to be very similar to methyl esters in terms of spray characteristics. The differences in SPL, SCA and SMD values for both types of biodiesels were lower than 4%. When considering the uncertainty (± 0.84%) and repeatability (±5%) ratios, the difference between the spray characteristics of methyl and ethyl esters was not major. Graphical abstract: [Figure not available: see fulltext.] © 2022, The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.Conference Object Energy and Exergy Analysis of a Roof-Mounted Photovoltaic System in Gebze-Turkey(Springer, 2024) Khalejan, Seyed Hamed Pour Rahmati; Cankurt, Tolga; Dede, Mehmet İsmet CanThis study investigates the electrical and thermal exergy, power conversion efficiency and exergy efficiency of a roof-mounted photovoltaic (PV) system considering environmental parameters such as solar irradiation, ambient temperature and wind speed over a year. The values of solar exergy and solar potential are obtained by taking into account the solar insolation. Experimental and theoretical results indicate that wind speed and surface temperature have significant effects on the thermal exergy and exergy efficiency of solar PV systems. The mean solar potential in the region was found to be 93%. In addition, the electrical exergy was varied from 9145 W to 40460 W and the thermal exergy of PV systems was varied from 1639 W to 6193 W. While the range of PV power conversion efficiency varies from 6.15% to 11.56% over a year, the range of exergy efficiency varies from 5.31% to 9.78%. © 2024, The Author(s), under exclusive license to Springer Nature Switzerland AG.Conference Object A Parametric Numerical Analysis of Laminar Hydrogen Diffusion Flames(International Association for Hydrogen Energy, IAHE, 2022) Korucu, Ayşe; Benim, Ali CemalAtmospheric, laminar, diffusion flames of hydrogen and air are numerically investigated. A detailed hydrogen combustion reaction scheme, in combination with the extended Zeldovich mechanism for the thermal nitrogen oxide formation are used. For comparison purposes, a global mechanism is also applied. The numerical procedure is first validated by comparisons with results of other authors. Subsequently, parametric studies are performed to find optimal solutions with respect to the related to the operation parameters of such flames to achieve minimum low nitrogen oxide emission levels. The question that are addressed include the Reynolds number effect on nitrogen emissions, and the interaction of neighbouring flames, when they are applied in an array. For ensuring an adequately fine resolution of the flame fronts, local adaptive grid refinement techniques are applied to track the flame front. For preliminary results the radiative heat loses has assumed to be insignificant however it should be taken into the account for the further analyses. The maximum temperature is predicted to be ~2040 K which is higher than the reported adiabatic stoichiometric flame temperature, 2023K for the exit velocity of 0.5 m/s. The radial mole fractions of N2 and H2 at the centerline are observed to be 0.66 and 0.41 respectively at the axial distance of 10 mm. Furthermore, the width of the high temperature region of the flame is observed to be ~6.5 mm. © 2022 Proceedings of WHEC 2022 - 23rd World Hydrogen Energy Conference: Bridging Continents by H2. All rights reserved.Conference Object Citation - WoS: 1Citation - Scopus: 1Modeling a Magneto-Rheological Fluid-Based Brake Via a Neural Network Method(Springer international Publishing Ag, 2022) Kucukoglu, Sefa Furkan; Dede, Mehmet Ismet Can; Ceccarelli, MarcoIdentifying the model of a magneto-rheological (MR) fluid-based brake is extremely important for designing and controlling a haptic device with hybrid actuation. Therefore, in this study, an Elman Recurrent Neural Network (ERNN) is designed to understand and model a characterization of an MR fluid-based rotational brake. Three important factors that affect the MR brake's performance are chosen as inputs: current, speed, and the first derivative of the input current. The proposed network is trained, and the performance of the network is tested with three different experimental scenarios. Then, the effect of these inputs on the system is investigated. According to the results, it can be said that the designed ERNN is a good candidate for modelling an MR brake.Conference Object Citation - Scopus: 1Kinematic Representation of a Biomimetic Squid Soft Robot's Arms in a Simulation Environment(Springer international Publishing Ag, 2022) Emet, Hazal; Dede, M. I. CanBiomimetic robot systems have received attention from researchers and in accordance the implementation of soft robotic arms has been studied. Kinematic and dynamic modeling of robots with infinite degrees of freedom is challenging and a number of methods have been proposed. In this work, a procedure is proposed to represent soft robot arm motion in a simulation environment. A biomimetic squid robot is used as a case study. This robot's soft arms are modeled by using the Piecewise Constant Curvature approach. This model is visualized by discretizing the soft arms into a finite number of rigid-body manipulators in MatLab using its 3D animation toolbox.
- «
- 1 (current)
- 2
- 3
- »