Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
36 results
Search Results
Article Citation - WoS: 1Citation - Scopus: 1Analysis and Comparison of the Projectile Impact Response of an Electron Beam Melt-Ti64 Body Centered Cubic Lattice-Cored Sandwich Plate(Springer, 2025) Erten, H.İ.; Çimen, G.; Yıldıztekin, F.M.; Güden, M.Background: One potential application of additively fabricated lattice structures is in the blade containment rings of gas turbine engines. The blade containment rings are expected to be able to absorb the kinetic energy of a released blade (broken blade) in order to protect the engine parts from damaging. Metallic lattice-cored sandwich plates provide a gap (free space) between two face sheets, which helps to arrest the released blade and increases the energy absorption capability of containment rings. Objective: The objective was to investigate numerically the projectile impact response of Body-Centered-Cubic (BCC) Electron-Beam-Melt (EBM) lattice-cored/Ti64 face sheet sandwich plates as compared with that of an equal-mass monolithic EBM-Ti64 plate. Methods: The projectile impact simulations were implemented in LS-DYNA using the previously determined flow stress and damage models and a spherical steel impactor at the velocities ranging from 150 to 500 m s−1. The experimental projectile impact tests on the monolithic plate were performed at two different impact velocities and the results were used to confirm the validity of the used flow stress and damage models for the monolithic plate models. Results: Lower impact stresses were found numerically in the sandwich plate as compared with the monolithic plate at the same impact velocity. The bending and multi-cracking of the struts over a wide area in the sandwich plate increased the energy absorption and resulted in the arrest of the projectile at relatively high velocities. While monolithic plate exhibited a local bent area, resulting in the development of high tensile stresses and the projectile perforations at lower velocities. Conclusions: The numerical impact stresses in the sandwich plate were distributed over a wider area around the projectile, leading to the fracture and bending of many individual struts which significantly increased the resistance to the perforation. Hence, the investigated lattice cell topology and cell, strut, and face sheet sizes and the lattice-cored sandwich plate was shown potentially more successful in stopping the projectiles than the equal-mass monolithic plates. © The Author(s) 2025.Conference Object Citation - Scopus: 3A Continuously Variable Transmission System Designed for Human–robot Interfaces(Springer, 2021) Mobedi, Emir; Dede, Mehmet İsmet CanWithin a predefined limit, continuously variable transmission (CVT) systems can continuously vary the power transmission ratio. The transmission in CVTs is achieved via friction, belt or gear systems. If CVT designs can incorporate backdrivability, independent output position and impedance variation, shock absorbtion, and low mass and inertia, they can be employed in human–robot interfaces. Among various types of CVT designs, the two-cone drive CVT designs have a major drawback since the output torque and position cannot be changed independent of each other. The friction wheel used in this design does not have a holonomic motion capability and causes this inconvenience. In order to overcome this problem, a sphere is used in this work for the CVT design as the transmission element. In addition, it is stated in the literature that common CVT drive systems do not have the capability to be used in cyclic bidirectional motion. In the presented CVT design, a second sphere is added to the system with two springs from the lower part of the cones for pretension in order to solve the bidirectional transmission problem. In this paper, the working principle and conceptual design details of the novel two-cone CVT drive are presented. Experimental results showed that the novel CVT has the capacity to transmit bidirectional power with some accuracy. © 2021, Springer Nature Singapore Pte Ltd.Conference Object Citation - Scopus: 3Four-bar function generation using excel solver(Springer, 2023) Söylemez, Eres; Kiper, GökhanThe Chapter presents a simple and efficient way of approximating a function with a four-bar mechanism using four or five design parameters including one or both of the initial crank angles. The method only involves solution of linear set of equations and evaluating determinants, whereas nonlinear equations are numerically solved using a simple program such as Excel. So, the method is easy to explain and can be taught in an undergraduate course along with the wellknown linear three precision point synthesis problem. Precision point synthesis, order synthesis, mixed order synthesis, least squares approximation and extreme point synthesis can all be treated using the same method. The proposed method is illustrated with numerical examples for all mentioned synthesis problems and shown to be quite efficient with very low amount of structural error values.Article Citation - WoS: 2Citation - Scopus: 3Design and Manufacturing of a Hip Joint Motion Simulator With a Novel Modular Design Approach(Springer, 2023) Torabnia, Shams; Mihçin, Şenay; Lazoğlu, İsmailThe study is aimed to develop a hip joint wear simulator using a modular design approach to help experimentally monitor and control critical wear parameters to validate in-silico wear models. The proper control and application of wear parameters such as the range of motion, and the applied force values while estimating the lost material due to wear are essential for thorough analysis of wear phenomena for artificial joints. The simulator's dynamics were first modeled, then dynamic loading data was used to calculate the forces, which were further used for topology optimization to reduce the forces acting on each joint. The reduction of the link weights, connected to the actuators, intends to improve the quality of motion transferred to the femoral head. The modular design approach enables topology-optimized geometry, associated gravitational and dynamic forces, resulting in a cost-effective, energy-efficient product. Moreover, this design allows integration of the subject specific data by allowing different boundary conditions following the requirements of industry 5.0. Overall, the in-vitro motion stimulations of the hip-joint prosthesis and the modular design approach used in the study might help improve the accuracy and the effectiveness of wear simulations, which could lead into the development of better and longer-lasting joint prostheses for all. The subject-specific and society-based daily life data implemented as boundary conditions enable inclusion of the personalized effects. Next, with the results of the simulator, CEN Workshop Agreement (CWA) application is intended to cover the personalized effects for previously excluded populations, providing solution to inclusive design for all.Conference Object Citation - Scopus: 3Design and Balancing of a Novel 2r1t Manipulator With Remote Center of Motion(Springer, 2023) Yılmaz, Tuğrul; Kiper, GökhanThe paper presents a novel manipulator design to be used as an endoscope holder for endonasal skull base surgeries. The manipulator should provide two rotational and one translational motions for the endoscope, where it should be able to be oriented about and slide along the tip of the nostril of a patient as a pivot point. First, suitable manipulators with remote center motion are investigated. Manipulators with serial and hybrid kinematic structure and redundant manipulators with a passive joint are examined. A serial manipulator with a circular arc as the second rotation axis is chosen for the detailed design. The novelty of the kinematic structure of the manipulator is that the end-effector heave motion is achieved in a tangential direction to the circular arc. The constructional design and counter-mass balancing solution for the manipulator are presented. The total assembly mass is 11.6 kg for navigating an endoscope of 0.44 kg mass.Article Citation - WoS: 9Citation - Scopus: 11Experimental Investigation of Spray Characteristics of Ethyl Esters in a Constant Volume Chamber(Springer, 2022) Ulu, Anılcan; Yıldız, Güray; Özkol, Ünver; Rodriguez, Alvaro DiezAbstract: Biodiesels are mainly produced via the utilization of methanol in transesterification, which is the widespread biodiesel production process. The majority of this methanol is currently obtained from fossil resources, i.e. coal and natural gas. However, in contrast with methanol, biomass-based ethanol can also be used to produce biodiesels; this could allow the production line to become fully renewable. This study aimed to investigate the spray characteristics of various ethyl ester type biodiesels derived from sunflower and corn oils in comparison to methyl esters based on the same feedstocks and reference petroleum-based diesel. Spray penetration length (SPL) and spray cone angle (SCA) were experimentally evaluated in a constant volume chamber allowing optical access, under chamber pressures of 0, 5, 10 and 15 bar and injection pressures of 600 and 800 bar. Sauter mean diameter (SMD) values were estimated by using an analytical correlation. Consequently, ethyl esters performed longer SPL (2.8–20%) and narrower SCA (5.1–19%) than diesel under ambient pressures of 5 and 10 bar. Although the SMD values of ethyl esters were 48% higher than diesel on average, their macroscopic spray characteristics were very similar to those of diesel under 15 bar chamber pressure. Moreover, ethyl esters were found to be very similar to methyl esters in terms of spray characteristics. The differences in SPL, SCA and SMD values for both types of biodiesels were lower than 4%. When considering the uncertainty (± 0.84%) and repeatability (±5%) ratios, the difference between the spray characteristics of methyl and ethyl esters was not major.Conference Object Asymmetry in the Tension and Compression Flow Stress and the Effect of Sub-Cell Size on the Hardness of a Selective Laser Melt 316l Stainless Steel(Springer, 2022) Güden, Mustafa; Enser, Samed; Arslan Hamat, Burcu; Tanrıkulu, A. Alptuğ; Yavaş, HakanAn asymmetry between tension and compression tests was determined experimentally in the Selective Laser Melt (SLM) stainless steel 316L alloy in the building direction. The asymmetry was ascribed to the used biaxial scanning strategy which resulted in a strong alignment of 〈110〉 along the build direction (fiber texture) and a random distribution of 〈100〉, 〈110〉 and 〈111〉 directions normal to the building direction. The strong fiber texture in the building direction induced lower twinning stress in tension than in compression, while the tension and compression twining stresses were found similar in the normal to building direction. The favored twinning in the specimens tested in the building direction resulted in a higher tensile true fracture strain; hence, a higher ductility. Lastly, the hardness measurements made on the specimens having similar gain sizes, but different sub-cell sizes processed using higher and lower laser powers tended to support that the sub-cell boundaries in SLM-316L alloy acted as imperfect barriers to the dislocation motion.Conference Object Citation - Scopus: 2Experimental Compliance Matrix Derivation for Enhancing Trajectory Tracking of a 2-Dof High-Accelerated Over-Constrained Mechanism(Springer, 2022) Paksoy, Erkan; Dede, Mehmet İsmet Can; Kiper, GökhanIf the positioning accuracy of the end-effector of a robot has high priority, compliance characteristics of the elements of its mechanism should be considered. Due to the external loading on the robot, the dimensions of the elements change and this leads to positioning errors for the end-effector. In this paper, an experimental test setup and an experimental procedure are described to derive the compliance characteristics of a planar 2-degree-of-freedom mechanism.Article Citation - WoS: 5Citation - Scopus: 5Loop Based Classification of Planar Scissor Linkages(Springer, 2022) Kiper, Gökhan; Korkmaz, Koray; Gür, Şebnem; Yar Uncu, Müjde; Maden, Feray; Akgün, Yenal; Karagöz, CevahirScissor linkages have been used for several applications since ancient Greeks and Romans. In addition to simple scissor linkages with straight rods, linkages with angulated elements have been introduced in the last decades. In the related literature, two methods have been used to design scissor linkages, one of which is based on scissor elements, and the other is based on assembling loops. This study presents a systematic classification of scissor linkages as assemblies of rhombus, kite, dart, parallelogram and anti-parallelogram loops using frieze patterns and long-short diagonal connections. After the loops are replicated along a curve as a pattern, the linkages are obtained by selection of proper common link sections for adjacent loops. The resulting linkages are analyzed for their motions and they are classified as realizing scaling deployable, angular deployable or transformable motion. Some of the linkages obtained are novel. Totally 10 scalable deployable, 1 angular deployable and 8 transformable scissor linkages are listed. Designers in architecture and engineering can use this list of linkages as a library of scissor linkage topologies.Conference Object Digital Twin of a Servo Driver of a Servo Motor as a First Step Towards a Digital Twin of a Robot Mechanism(Springer, 2022) Küçükoğlu, Sefa Furkan; Carbone, Giuseppe; Dede, Mehmet İsmet CanDigital Twin (DT) offers us to acquire actual system’s critical information and hence, it may be possible to develop and produce more suitable systems in terms of low energy consumption and effectiveness. In this way, responsible consumption and production systems can be designed and the system’s parameters can be tuned via DT. In this study, the model of a servomotor system that is used for industrial purposes is experimentally obtained. This study consists of two steps. In the first step, within the embedded control of the system, position and velocity control loops are deactivated. Then through the servo driver, currents with sinusoidal waveforms at various frequencies are applied to the servomotor. The resultant angular velocity of the motor is monitored and recorded. The amplitude of the current is kept constant during this study. The frequency of the current, however, is increased logarithmically. By using these data, a first-order transfer function (TF) is identified for the motor model. In the second step, all control loops are activated. Consequently, the total servomotor system could be represented in a digital environment. Furthermore, the static friction issue is overcome by using a Coulomb friction model with stiction effect. Finally, several experiments are conducted and then results are compared with the digital model of the servomotor system. The results clearly show that digital model can fairly represent the physical system.