Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
8 results
Search Results
Review Citation - WoS: 13Citation - Scopus: 13A Review on Battery Thermal Management Strategies in Lithium-Ion and Post-Lithium Batteries for Electric Vehicles(Yıldız Technical University, 2023) Güngör, Şahin; Göçmen, Sinan; Çetkin, ErdalElectrification on transportation and electricity generation via renewable sources play a vital role to diminish the effects of energy usage on the environment. Transition from the conven- tional fuels to renewables for transportation and electricity generation demands the storage of electricity in great capacities with desired power densities and relatively high C-rate values. Yet, thermal and electrical characteristics vary greatly depending on the chemistry and struc- ture of battery cells. At this point, lithium-ion (Li-ion) batteries are more suitable in most applications due to their superiorities such as long lifetime, high recyclability, and capacities. However, exothermic electrochemical reactions yield temperature to increase suddenly which affects the degradation in cells, ageing, and electrochemical reaction kinetics. Therefore, strict temperature control increases battery lifetime and eliminates undesired situations such as lay- er degradation and thermal runaway. In the literature, there are many distinct battery thermal management strategies to effectively control battery cell temperatures. These strategies vary based on the geometrical form, size, capacity, and chemistry of the battery cells. Here, we focus on proposed battery thermal management strategies and current applications in the electric vehicle (EV) industry. In this review, various battery thermal management strategies are doc- umented and compared in detail with respect to geometry, thermal uniformity, coolant type and heat transfer methodology for Li-ion and post-lithium batteries.Article Citation - WoS: 5Citation - Scopus: 6Asymmetric Y-Shaped Micromixers With Spherical Mixing Chamber for Enhanced Mixing Efficiency and Reduced Flow Impedance(Isfahan University of Technology, 2021) Çetkin, Erdal; Miguel, A. F.Microfluidic devices have many attractive qualities such as low cost, small size, and in-field use. Micromixers are very important components of these devices because affect their efficiency. In a passive mixer, the structural characteristics of the mixer are crucial and must be analyzed. This paper presents a numerical study of the mixing in passive Y-shaped micromixers with a spherical mixing chamber for a volume constrained system. The effect of asymmetric bifurcated ducts, the angle in between the inflow ducts, eccentricity and, obstacles inserted in the mixing sphere, on the mixing efficiency and flow impedance is evaluated. Vortical structures characteristics and the possible occurrence of engulfment are also identified. The results show that flow impedance (pressure drop for unit volumetric flow rate) can be decreased greatly for the same mixing efficiency as the volume of the spherical mixing chamber is 20% of the total volume. Insertion of the obstacles into the sphere mixing chamber decreases the mixing efficiency while they increase the flow impedance. The results also show that spherical mixing chamber enhances mixing efficiency while decreasing flow impedance if the volume reserved for it is greater than a limit value which depends on the diameter and length scale ratios in between the mother and daughter ducts as well as the total volume. Overall, the paper documents the variation of mixing efficiency and flow impedance based on the geometrical parameters of three-dimensional asymmetric passive micromixer with sphere mixing chamber.Article Citation - WoS: 1Citation - Scopus: 2Emergence of Taperedducts in Vascular Designs With Laminar and Turbulent Flows(Begell House, 2014) Çetkin, ErdalHere we show that tapered ducts emerge in volumetrically bathed porous materials to decrease the resistance to the flow in laminar and turbulent flow regimes. The fluid enters the volume from one point and it is distributed to the entire volume. After bathing the volume, it is collected and leaves the volume from another point, i.e., two trees matched canopy to canopy. This paper shows that the flow architecture (i.e., design of the void spaces in a porous material) should be changed to obtain the minimum resistance to the flow as its size increases. Tapering the ducts decreases the order of the transition size, i.e., the size for changing from one construct to another to obtain the minimum pressure drop. The decrease in the pressure drop is 16% and 38% with the tapered ducts when the flow is laminar and turbulent, respectively. In addition, the volume ratios and the shape of the tapered ducts are documented. There is no design existing in nature with diameters of constant size in order to distribute and/or collect heat, fluid, and/or stress such as bones, rivers, veins, and tree branches. The emergence of the tapered ducts in designed porous materials is natural.Article Citation - WoS: 12Citation - Scopus: 11Inverted Fins for Cooling of a Non-Uniformly Heated Domain(Yıldız Teknik Üniversitesi, 2015) Çetkin, ErdalThis paper shows that the peak temperature of a non-uniformly heated region can be decreased by embedding high-conductivity tree-shaped inserts which is in contact with a heat sink from its stem. The volume fraction of the high-conductivity material is fixed, and so is the volume of the solid region. The length scale of the solid domain is L. Inside there is a cube-shaped region with length scale of 0.1L and heat production 100 times greater than the rest of the domain. The location of this hot spot was varied to uncover how its location affects the peak temperature and the design of inverted fins, i.e. highconductivity tree-shaped inserts. The volume fraction of the high-conductivity tree was varied for number of bifurcation levels of 0, 1 and 2. This showed that increasing the number of the bifurcation levels decreases the peak temperature when the volume fraction decreases. The optimal diameter ratios and optimal bifurcation angles at the each junction level are also documented. Y-shaped trees promise smaller peak temperatures than T-shaped trees. The location of the vascular tree in the z direction also affects the peak temperature when the heat generation is non-uniform. In addition, the peak temperature is minimum when z = 0.65L even though the hot spot is located on z = 0.75L.Article The Effect of Time Delay of Fluid Flow in a Vascularized Plate(MIM Research Group, 2018) Yenigün, Onur; Coşkun, Turgay; Çetkin, ErdalIn this study, we show the effect of time delay of coolant fluid flow into a vascularized plate on the peak temperature. Coolant flows along vascular channels which were embedded in a rectangular plate. Two kinds of vascular channel designs were investigated experimentally: parallel and tree-shaped. In the study, the peak temperatures were monitored and the coolant was pumped when the peak temperature reaches to 50°C, 70°C and 90°C. The performance comparison of two distinct designs is based on two criteria: the time required for the steady state condition after the coolant is pumped and the peak temperature after the steady state condition is conformed. The results show that the time required to reach steady-state condition increases as the time delay increases. The parallel and tree-shaped designs show similar performance (time required to reach steady state) with slightly improved performance in the tree-shaped design as the preset temperature for time delay increases. For instance, 4% decrease in the time required to reach steady-state with the tree-shaped design relative to the parallel design was achieved when the preset temperature for time delay is 90°C.Article Citation - WoS: 3Citation - Scopus: 4The Effect of Cooling on Mechanical and Thermal Stresses in Vascular Structures(Yıldız Teknik Üniversitesi, 2018) Çetkin, ErdalHere, we show how the vascular channel configuration and its shape affect the mechanical strength which is simultaneously subjected to heating and mechanical load. The material properties were defined as functions of temperature. The effect of channel cross-section on the coolant mass flow rate, peak temperature and peak stresses are documented. The results show that the resistances to flow of stresses and fluid is minimum with the circular channels while the resistance to the heat flow is the smallest with semi-circular channels. In addition, morphing the vascular design provides almost the smallest resistance to the heat flow with circular channels (0.3% difference in the peak temperature). This shows that even the convective resistances are the smallest with circular-cross section, overall thermal resistance is smaller in semi-circular design for the fixed fluid volume. The peak stress is smaller with hybrid design than the parallel designs for the entire pressure drop range. In addition, the effects of mechanical load, heating rate and reference temperature on the stress distribution are also documented. Furthermore, the thermal and mechanical stresses are also documented separately, and then compared with the coupled solution cases. The chief result of this paper is that for a coupled system minimizing only one of the resistance terms is not sufficient, all the resistances considered simultaneously in order to uncover the best performing design. In coupled solutions, we documented the simulation results with temperature dependent material properties and the resistances to the heat and fluid flow is affected by the mechanical deformations. In addition, the results show that the designs should be free to vary, the unexpected designs can be the best performing designs for the given parameters and constraints. Therefore, the design parameters based on the experience does not always yield the best performing designs as the objectives and constraints vary.Article Citation - WoS: 2Citation - Scopus: 2Vascular Structures for Smart Features: Self-Cooling and Self-Healing(Yıldız Teknik Üniversitesi, 2017) Çetkin, ErdalHere we show how smart features of self-cooling and self-healing can be gained to mechanical systems with embedded vascular structures. Vascular structures mimic the circulatory system of animals. Similar to blood distribution from heart to the animal body, vascular channels provide the distribution of coolant and/or healing agent from a point to the entire body of a mechanic system. Thus the mechanic system becomes capable of cooling itself under unpredictable heat attacks and capable of healing itself as cracks occur due to applied mechanical loads. These smart features are necessary for advanced devices, equipment and vehicles. The essential design parameter is vascularization in order to provide smart features. There are distinct configurations for vascularization such as radial, tree-shaped, grid and hybrids of these designs. In addition, several theories are available for the shape optimization of vascular structures such as fractal theory and constructal theory. Unlike fractal theory, constructal theory does not include constraints based on generic algorithms and dictated assumptions. Therefore, constructal theory approach is discussed in this paper. This paper shows how smart features can be gained to a mechanical system while its weight decreases and its mechanical strength increases simultaneously.Article Citation - WoS: 3Citation - Scopus: 3Constructal vascularized structures(Walter de Gruyter GmbH, 2015) Çetkin, ErdalSmart features such as self-healing and selfcooling require bathing the entire volume with a coolant or/and healing agent. Bathing the entire volume is an example of point to area (or volume) flows. Point to area flows cover all the distributing and collecting kinds of flows, i.e. inhaling and exhaling, mining, river deltas, energy distribution, distribution of products on the landscape and so on. The flow resistances of a point to area flow can be decreased by changing the design with the guidance of the constructal law, which is the law of the design evolution in time. In this paper, how the flow resistances (heat, fluid and stress) can be decreased by using the constructal law is shown with examples. First, the validity of two assumptions is surveyed: using temperature independent Hess-Murray rule and using constant diameter ducts where the duct discharges fluid along its edge. Then, point to area types of flows are explained by illustrating the results of two examples: fluid networks and heating an area. Last, how the structures should be vascularized for cooling and mechanical strength is documented. This paper shows that flow resistances can be decreased by morphing the shape freely without any restrictions or generic algorithms.