Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
8 results
Search Results
Research Project Üstüniletken MgB2 tellerin üretimi ve karakterizasyonu(TÜBİTAK - Türkiye Bilimsel ve Teknolojik Araştırma Kurumu, 2005) Okur, Salih; Özyüzer, Lütfi; Abukay, Doğan; Emirdağ, Mehtap; Tanoğlu, Metin; Eğilmez, MehmetMgB2 alaşımının 39 K lik Tc kritik sıcaklığına sahip bir üstüniletken olduğunun 2001 de keşfedilmesi çok iyi üstüniletken olduğu bilinen NbTi ve NbsSn malzemelerinin yanısıra uygulamaya daha yakın yeni bir üstüniletken malzeme olma ümidini de artırmıştır. O günden bu güne MgB2 üstüniletken tellerin üretilmesi konusunda çok etkileyici bir aşama kaydedilmiştir. Daha yüksek kritik akım yoğunluğuna ulaşmak için gerekli parametrelerin araştırılması konusunda birkaç teknik geliştirilmiştir. Bunların arasında 'tüp içinde toz ' (TIT) adı verilen metot diğerlerine göre daha pratik ve ümit verici gözükmektedir. Bazı metal ve alaşımların TIT işleminde kılıf malzeme olarak kullanılmaya uygun bulunmuştur. Bunlardan demir ve alaşımları kısmen MgB2 özelliğini bozmadığı gibi manyetik ekranlama yaparak dış manyetik alanların kritik akım üzerindeki yan etkilerini azaltarak daha yüksek değerlere ulaşılmıştır. TIT yöntemi ile MgB2 üretimi sırasında iki farklı teknik vardır. Birisinde reaktif MgB2 tozlar kulanılırken diğerinde belli kimyasal oranlarda karıştırılmış reaktif olmayan Mg+2B tozları kullanılmaktadır. Daha sonra bu tozlar reaksiyon yapmayan bir tüp veya kapsül içine kapatılıp 900 ile 1000 °C civarında belirli bir süre tavlanmaktadır. Bu yöntem ile Demir kılıflı MgB2 üstüniletken tellerinden 15 K de 10 A/cm civarında bir Jc kritik akım yoğunluğuna ulaşılmıştır. Bu projede ilk adım olarak borik asitten M&B2 elde edilmiş ve elde edilen MgB2 in yapısını XRD ve SEM EDX mikroskopu ile karakterize edilmiştir. Uygun bir saflığa sahip MgB2 e ulaşıldığında elektriksel ve manyetik özellikleri pellet haline getirilip incelenmiştir, ikinci adımda ise üretilen MgB2 tozlarından üstüniletken MgB2 tel ve teyplerin TIT yöntemi ile üretilmiştir ve Cu, Fe, ve paslanmaz çelik gibi MgB2 ile etkileşmeyen malzemeler kılıf olarak kullanılanarak üretilmeye çalışılmış ve bu üstüniletken MgB2 tellerin özdirenç ve manyetik alana bağlı olarak kritik akım (Jc) karakteristiğinin sıcaklığa bağımlılığı incelenmiştir.Research Project Üstüniletken magnezyum borür (MgB2) tellerinin yüksek akım ve yüksek manyetik alan uygulamaları için geliştirilmesi(2008) Okur, Salih; Tarhan, Enver; Büyükköse, Serkan; Özyüzer, Lütfi; Tanoğlu, Metin; Emirdağ, Mehtap[No Abstract Available]Article Citation - WoS: 3Citation - Scopus: 3Thermostable Tensoresistors of Co Doped Gasb-Fega1.3 Eutectic Composites(Elsevier Ltd., 2008) Rahimov, R. N.; Khalilova, A. A.; Arasly, D. H.; Aliyev, M. I.; Tanoğlu, Metin; Özyüzer, LütfiThe microstructure and tensoresistive properties of GaSb-FeGa1.3 eutectic composites doped with 0.1% Co have been investigated. It was found that the Co impurity atoms mainly accumulate in the metallic inclusions. The length of the inclusions in GaSb-FeGa1.3〈Co〉 was measured to be about half of those in undoped GaSb-FeGa1.3 eutectics. The tensometric characteristics of gauges based on GaSb-FeGa1.3〈Co〉 have been found to be more thermostable than undoped samples. © 2008 Elsevier B.V. All rights reserved.Article Citation - WoS: 6Citation - Scopus: 11Electrical and Mechanical Properties of Superconducting Mgb2/Mg Metal Matrix Composites(IOP Publishing Ltd., 2006) Eğilmez, Mehmet; Özyüzer, Lütfi; Tanoğlu, Metin; Okur, Salih; Kamer, Orhan; Öner, YıldırhanMgB2/Mg composites were prepared using a metal matrix composite fabrication method that offers the potential to produce superconducting wires as an alternative approach to the powder in tube process. To obtain composites, MgB2 and Mg powders were mixed at different weight fractions and uniaxially pressed in a cylindrical die under the pressure of 0.5 and 1.0GPa for two hours at various temperatures. The x-ray diffraction technique was used for phase identification. Temperature dependence of resistivity and magnetization measurements were carried out to determine superconducting properties. The effects of composite fabrication temperature and the addition of the Mg on the mechanical properties of MgB2/Mg composites were investigated. For this purpose, the compressive mechanical testing was performed to measure the elastic modulus and fracture strength values of the composites. It was found that the relative weight fraction of the Mg and the fabrication conditions of the composites have considerable effect on the superconducting and mechanical properties of the composites.Conference Object Citation - WoS: 39Citation - Scopus: 48Temperature Dependence of Electrical Conductivity in Double-Wall and Multi-Wall Carbon Nanotube/Polyester Nanocomposites(Springer Verlag, 2007) Şimşek, Yılmaz; Özyüzer, Lütfi; Seyhan, Abdullah Tuğrul; Tanoğlu, Metin; Schulte, KarlThe aim of this study is to investigate temperature dependence of electrical conductivity of carbon nanotube (CNT)/polyester nanocomposites from room temperature to 77 K using four-point probe test method. To produce nanocomposites, various types and amounts of CNTs (0.1, 0.3 and 0.5 wt.%) were dispersed via 3-roll mill technique within a specially formulized resin blend of thermoset polyesters. CNTs used in the study include multi walled carbon nanotubes (MWCNT) and double-walled carbon nanotubes (DWCNT) with and without amine functional groups (-NH2). It was observed that the incorporation of carbon nanotubes into resin blend yields electrically percolating networks and electrical conductivity of the resulting nanocomposites increases with increasing amount of nanotubes. However, nanocomposites containing amino functionalized carbon nanotubes exhibit relatively lower electrical conductivity compared to those with non-functionalized carbon nanotubes. To get better interpretation of the mechanism leading to conductive network via CNTs with and without amine functional groups, the experimental results were fitted to fluctuation-induced tunneling through the barriers between the metallic regions model. It was found that the results are in good agreement with prediction of proposed model.Conference Object Citation - WoS: 6Citation - Scopus: 5Electrical and Microstructural Properties of Superconducting Mgb 2/Mg Composites(Trans Tech Publications, 2004) Eğilmez, Mehmet; Günel, Aylin; Okur, Salih; Tanoğlu, Metin; Özyüzer, LütfiMgB2/Mg composites were prepared to improve mechanical properties of brittle superconducting MgB2. MgB2 and Mg powders were mixed at different weight ratios and uniaxially pressed in a cylindrical dye at 0.5 GPa and at various temperatures for two hours to prepare MgB2/Mg composites. X-ray diffraction, SEM and EDX were used for phase identification and microstructural characterization. In addition to the main MgB2 and Mg phases, the microstructural studies have indicated the presence of a minor amounts of second phases, namely MgO and B-rich compounds. The surface morphology, grain size and porosity ratio of the samples prepared under various temperatures were also investigated. The resistivity measurements were performed in the range of room temperature to 15 K. The effect of excess Mg and secondary phases on critical temperature of MgB2/Mg composites were studied.Article Citation - WoS: 3Citation - Scopus: 4Strain Gauges of Gasb-Fega1.3 Eutectic Composites(Springer Verlag, 2004) Aliyev, M.I.; Khalilova, A. A.; Arasly, D. H.; Rahimov, R. N.; Tanoğlu, Metin; Özyüzer, LütfiA needle-shaped metallic FeGa1.3 phase oriented in a specific direction and uniformly distributed within a GaSb matrix was grown by a vertical Bridgman method. Strain-gauge characteristics, such as strain-sensitivity coefficient (S), temperature coefficient of strain sensitivity (TCS) and temperature coefficient of resistance, of GaSb and GaSb-FeGa1.3 eutectic alloy have been investigated in the range of 200 to 400 K under deformation up to strains of 1.3 × 10-3. The value of S of the GaSb-FeGa1.3 composition is measured to be 40 ± 5 and its TCS is about 0.2% deg-1 when the current is perpendicular to the needles and the needles are parallel to the plane of the gauge substrate. The strain-sensitivity characteristics are linear and hysteresis free in the investigated temperature range in the aforementioned direction. It was found that GaSb-FeGa1.3-based strain gauges possess better deformation characteristics than GaSb-based gauges.Article Citation - WoS: 10Citation - Scopus: 9Features of Electron and Phonon Processes in Gasb-Fega1.3 Eutectics(IOP Publishing Ltd., 2003) Aliyev, M. I.; Khalilova, A. A.; Arasly, D. H.; Rahimov, R. N.; Tanoğlu, Metin; Özyüzer, LütfiEutectic alloys of GaSb-FeGa1.3 were prepared by the vertical Bridgman method. A microstructure with the needle-shaped metallic FeGa1.3 phase oriented in a specific direction and uniformly distributed within the GaSb matrix was obtained. In GaSb-FeGa1.3 eutectics, the electrical and thermal conductivity, thermal diffusivity, thermoelectric power and Hall coefficients were investigated in a wide temperature range. These properties were measured at different mutual directions of current, thermal flow, magnetic field and metal phase inclusions. The influence of metallic inclusions on these properties was revealed and the distinctive characteristics of electron and phonon processes were established.