Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
15 results
Search Results
Article Citation - WoS: 7Citation - Scopus: 7Investigating the Effects of Pa66 Electrospun Nanofibers Layered Within an Adhesive Composite Joint Fabricated Under Autoclave Curing(American Chemical Society, 2023) Esenoğlu, Gözde; Tanoğlu, Metin; Barışık, Murat; İplikçi, Hande; Yeke, Melisa; Nuhoğlu, Kaan; Türkdoğan, Ceren; Martin, Seçkin; Aktaş, Engin; Dehneliler, Serkan; Gürbüz, Ahmet Ayberk; İriş, Mehmet ErdemEnhancing the performance of adhesively joined composite components is crucial for various industrial applications. In this study, polyamide 66 (PA66) nanofibers produced by electrospinning were coated on unidirectional carbon/epoxy prepregs to increase the bond strength of the composites. Carbon/epoxy prepregs with/without PA66 nanofiber coating on the bonding region were fabricated using the autoclave, which is often used in the aerospace industry. The single lap shear Charpy impact energy and Mode-I fracture toughness tests were employed to examine the effects of PA66 nanofibers on the mechanical properties of the joint region. Scanning electron microscopy (SEM) was used to investigate the nanofiber morphology and fracture modes. The thermal characteristics of Polyamide 66 nanofibers were explored by using differential scanning calorimetry (DSC). We observed that the electrospun PA66 nanofiber coating on the prepreg surfaces substantially improves the joint strength. Results revealed that the single lap shear and Charpy impact strength values of the composite joint are increased by about 79 and 24%, respectively, by coating PA66 nanofibers onto the joining region. The results also showed that by coating PA66 nanofibers, the Mode-I fracture toughness value was improved by about 107% while the glass transition temperature remained constant.Article Citation - WoS: 9Citation - Scopus: 13Analysis of Adhesively Bonded Joints of Laser Surface Treated Composite Primary Components of Aircraft Structures(Elsevier, 2023) Martin, Seçkin; Nuhoğlu, Kaan; Aktaş, Engin; Tanoğlu, Metin; İplikçi, Hande; Barışık, Murat; Yeke, Melisa; Türkdoğan, Ceren; Esenoğlu, Gözde; Dehneliler, SerkanThe performance of the adhesively bonded aerospace structures highly depends on the adhesion strength between the adhesive and adherents, which is affected by, in particular, the condition of the bonding surface. Among the various surface treatment methods, as state of the art, laser surface treatment is a suitable option for the CFRP composite structures to enhance the adhesion performance, adjusting the roughness and surface free energy with relatively minimizing the damage to the fibers. The aim of this study is the validation and evaluation of the adhesive bonding behavior of the laser surface-treated CFRP composite structures, using the finite element technique to perform a conservative prediction of the failure load and damage growth. Such objectives were achieved by executing both experimental and numerical analyses of the secondary bonded CFRP parts using a structural adhesive. In this regard, to complement physical experiments by means of numerical simulation, macro-scale 3D FEA of adhesively bonded Single Lap Joint and Skin-Spar Joint specimens has been developed employing the Cohesive Zone Model (CZM) technique in order to simulate bonding behavior in composite structures especially skin-spar relation in the aircraft wing-box.Article Citation - WoS: 3Citation - Scopus: 3Enhancement of Filament Wound Glass Fiber/Epoxy-based Cylindrical Composites by Toughening With Single-Walled Carbon Nanotubes(SAGE Publications, 2022) Ay Solak, Zeynep; Kartav, Osman; Tanoğlu, MetinIn this study, the effect of incorporating nano-sized fillers (noncovalently functionalized with ethoxylated alcohol chemical-vapor-deposition-grown SWCNTs) within an epoxy resin on the performance of filament wound glass fiber (GF)-based cylindrical composites (GFCCs) was investigated. For this purpose, SWCNTs were dispersed with the concentration of 0.05 and 0.1 weight percent (wt.%) within an epoxy resin using mechanical stirring and calendaring (3-roll-milling) techniques. The rheological behavior of the SWCNT incorporated epoxy mixture was characterized to determine the suitability of blends for the filament winding process. It was revealed that the viscosity value of the resin was not significantly affected by the addition of SWCNTs in given concentrations. Moreover, contact angle measurements were also performed on the SWCNT/epoxy blends dropped on the GF for the evaluation of the wettability behavior of the GF in the presence of the SWCNTs in relevant concentrations. Eventually, it was observed that the wettability behavior of GF was not reasonably affected by the presence of the SWCNTs. The double cantilever beam (DCB), flexural, and short beam shear (SBS) tests were performed on the reference and SWCNT-modified GFCC specimens to evaluate the effects of the SWCNT presence on the interlaminar fracture toughness and out-of-plane properties of GFCCs. The fractured surfaces after the DCB and SBS tests were analyzed under the scanning electron microscopy to reveal the toughening mechanisms and the filler morphologies. Consequently, although SWCNT incorporation was on the outermost layer of GFCCs, it was found that the interlaminar shear strength (ILSS) values and Mode I interlaminar fracture toughness values of the curved composite samples were improved up to 22 and 216%, respectively, due to the presence of the SWCNTs.Article Citation - WoS: 8Citation - Scopus: 9Dynamic Behavior Predictions of Fiber-Metal Laminate/Aluminum Foam Sandwiches Under Various Explosive Weights(SAGE Publications, 2016) Baştürk, Suat Bahar; Tanoğlu, Metin; Çankaya, Mehmet Alper; Eğilmez, Oğuz ÖzgürApplication of blast tests causes some problems to characterize the performance of panels due to the drastic conditions of explosive medium. Real test has high safety concerns and is not easily accessible because of its extra budget. Some approaches are needed for the preliminary predictions of dynamic characteristics of panels under blast loading conditions. In this study, the response of sandwiches under blast effect was evaluated by combining quasi-static experiments and computational blast test data. The primary aim is to relate the quasi-static panel analysis to dynamic blast load. Based on this idea, lightweight sandwich composites were subjected to quasi-static compression loading with a special test apparatus and the samples were assumed as single degree-of-freedom mass-spring systems to include dynamic effect. This approach provides a simpler way to simulate the blast loading over the surface of the panels and reveals the possible failure mechanisms without applying any explosives. Therefore the design of the panels can be revised by considering quasi-static test results. In this work, the peak deflections and survivabilities of sandwiches for various explosive weights were predicted based on the formulations reported in the literature. Major failure types were also identified and evaluated with respect to their thicknesses.Article Citation - WoS: 24Citation - Scopus: 26Cure Kinetics of Vapor Grown Carbon Nanofiber (vgcnf) Modified Epoxy Resin Suspensions and Fracture Toughness of Their Resulting Nanocomposites(Elsevier Ltd., 2009) Seyhan, Abdullah Tuğrul; Sun, Z.; Deitzel, J.; Tanoğlu, Metin; Heider, D.In this study, the cure kinetics of Cycom 977-20, an aerospace grade toughened epoxy resin, and its suspensions containing various amounts (1, 3 and 5 wt.%) of vapor grown carbon nanofibers (VGCNFs) with and without chemical treatment were monitored via dynamic and isothermal dynamic scanning calorimetry (DSC) measurements. For this purpose, VGCNFs were first oxidized in nitric acid and then functionalized with 3-glycidoxypropyltrimethoxy silane (GPTMS) coupling agent. Fourier transform infrared (FTIR) spectroscopy was subsequently used to verify the chemical functional groups grafted onto the surfaces of VGCNFs. Sonication technique was conducted to facilitate proper dispersion of as-received, acid treated and silanized VGCNFs within epoxy resin. Dynamic DSC measurements showed that silanized VGCNF modified resin suspensions exhibited higher heat of cure compared to those with as-received VGCNFs. Experimentally obtained isothermal DSC data was then correlated with Kamal phenomenological model. Based on the model predictions, it was found that silanized VGCNFs maximized the cure reaction rates at the very initial stage of the reaction. Accordingly, an optimized curing cycle was applied to harden resin suspensions. Fracture testing was then carried out on the cured samples in order to relate the curing behavior of VGCNF modified resin suspensions to mechanical response of their resulting nanocomposites. With addition of 1 wt.% of silanized VGCNFs, the fracture toughness value of neat epoxy was found to be improved by 12%. SEM was further employed to examine the fracture surfaces of the samples.Article Citation - WoS: 29Citation - Scopus: 31Cure Kinetics of Epoxy Resin-Natural Zeolite Composites(Springer Verlag, 2008) Cansever Erdoğan, Beyhan; Seyhan, Abdullah Tuğrul; Ocak, Yılmaz; Tanoğlu, Metin; Balköse, Devrim; Ülkü, SemraThe cure kinetics of epoxy resin and epoxy resin containing 10 mass% of natural zeolite were investigated using differential scanning calorimetry (DSC). The conformity of the cure kinetic data of epoxy and epoxy-zeolite system was checked with the auto-catalytic cure rate model. The results indicated that the hydroxyl group on the zeolite surface played a significant role in the autocatalytic reaction mechanism. This group was able to form a new transition state between anhydride hardener and epoxide group. The natural zeolite particles acted as catalyst for the epoxy system by promoting its curing rate.Article Citation - WoS: 46Citation - Scopus: 53Preparation and Characterization of Fe2o3-Tio2 Thin Films on Glass Substrate for Photocatalytic Applications(Elsevier Ltd., 2006) Çelik, Erdal; Yıldız, A. Y.; Ak Azem, Necmiye Funda; Tanoğlu, Metin; Toparlı, Mustafa; Emrullahoğlu, Ö. Faruk; Özdemir, İ.Fe2O3-TiO2 coatings were successfully prepared on glass slide substrates using sol-gel method for photocatalytic applications. The phase structure, thermal, microstructure and surface properties of the coatings were extensively characterized by using X-ray diffractometry (XRD), differential thermal analysis/thermograviometry (DTA/TG), scanning electron microscopy (SEM) and atomic force microscopy (AFM). Their adhesion and absorbance properties were investigated by a scratch tester and UV-vis spectroscopy. Four different solutions were prepared by changing Fe/Ti molar ratios. Glass substrates were coated by solutions of Ti-alkoxide, Fe-chloride, glaciel acetic acid and isopropanol. The obtained gel films were dried at 300 °C for 10 min and subsequently heat-treated at 500 °C for 5 min in air. The oxide thin films were annealed at 600 °C for 60 min in air. The influence of Fe3+ concentration and number of layers on structure of the films was established. In addition, XRD results revealed that Fe2O3-TiO2 films composed of TiO2, Fe2Ti3O9, Ti3O5 and Fe3O4 phases. According to DTA/TG result, it was determined that endothermic and exothermic reactions were formed at temperatures between 80 and 650 °C due to solvent removal, combustion of carbon based materials and oxidation of Fe and Ti. SEM observations exhibited that the coating structure becomes more homogeneous depending on an increase of Fe/Ti molar ratios and thus a regular surface morphology forms with increasing Fe/Ti ratio. It was also seen that as the Fe/Ti ratio increases the surface roughness of the films increases. Critical adhesion force of thin films with Fe/Ti ratio of 0, 0.07, 0.18 and 0.73 were found to be 9, 25, 28 and 21 mN, respectively. The methylene blue solutions photocatalyzed by TiO2 based thin films shows characteristic absorption bands at 420 nm.Article Citation - WoS: 6Citation - Scopus: 11Electrical and Mechanical Properties of Superconducting Mgb2/Mg Metal Matrix Composites(IOP Publishing Ltd., 2006) Eğilmez, Mehmet; Özyüzer, Lütfi; Tanoğlu, Metin; Okur, Salih; Kamer, Orhan; Öner, YıldırhanMgB2/Mg composites were prepared using a metal matrix composite fabrication method that offers the potential to produce superconducting wires as an alternative approach to the powder in tube process. To obtain composites, MgB2 and Mg powders were mixed at different weight fractions and uniaxially pressed in a cylindrical die under the pressure of 0.5 and 1.0GPa for two hours at various temperatures. The x-ray diffraction technique was used for phase identification. Temperature dependence of resistivity and magnetization measurements were carried out to determine superconducting properties. The effects of composite fabrication temperature and the addition of the Mg on the mechanical properties of MgB2/Mg composites were investigated. For this purpose, the compressive mechanical testing was performed to measure the elastic modulus and fracture strength values of the composites. It was found that the relative weight fraction of the Mg and the fabrication conditions of the composites have considerable effect on the superconducting and mechanical properties of the composites.Article Citation - WoS: 69Citation - Scopus: 77Morphosynthesis of Caco3 at Different Reaction Temperatures and the Effects of Pdda, Ctab, and Edta on the Particle Morphology and Polymorph Stability(Elsevier Ltd., 2007) Altay, E.; Shahwan, Talal; Tanoğlu, MetinFacile precipitation of CaCO3 was performed using aqueous solutions of CaCl2 with Na2CO3 over a wide range of mixing and aging temperatures. The precipitation process was then repeated in the presence of PDDA, CTAB, and EDTA at the mixing temperatures of 30 °C, 50 °C, 70 °C, and 90 °C. The presence of these additives was seen to greatly suppress the formation of aragonite. Among these additives, EDTA was the one that showed the most prominent effects on particle morphology of CaCO3. The sequence of pH adjustment appeared to be a critical factor for the additive functionality.Conference Object Citation - WoS: 39Citation - Scopus: 48Temperature Dependence of Electrical Conductivity in Double-Wall and Multi-Wall Carbon Nanotube/Polyester Nanocomposites(Springer Verlag, 2007) Şimşek, Yılmaz; Özyüzer, Lütfi; Seyhan, Abdullah Tuğrul; Tanoğlu, Metin; Schulte, KarlThe aim of this study is to investigate temperature dependence of electrical conductivity of carbon nanotube (CNT)/polyester nanocomposites from room temperature to 77 K using four-point probe test method. To produce nanocomposites, various types and amounts of CNTs (0.1, 0.3 and 0.5 wt.%) were dispersed via 3-roll mill technique within a specially formulized resin blend of thermoset polyesters. CNTs used in the study include multi walled carbon nanotubes (MWCNT) and double-walled carbon nanotubes (DWCNT) with and without amine functional groups (-NH2). It was observed that the incorporation of carbon nanotubes into resin blend yields electrically percolating networks and electrical conductivity of the resulting nanocomposites increases with increasing amount of nanotubes. However, nanocomposites containing amino functionalized carbon nanotubes exhibit relatively lower electrical conductivity compared to those with non-functionalized carbon nanotubes. To get better interpretation of the mechanism leading to conductive network via CNTs with and without amine functional groups, the experimental results were fitted to fluctuation-induced tunneling through the barriers between the metallic regions model. It was found that the results are in good agreement with prediction of proposed model.