Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
7 results
Search Results
Article Citation - WoS: 18Citation - Scopus: 20Thermal Curing Behavior of Mwcnt Modified Vinyl Ester-Polyester Resin Suspensions Prepared With 3-Roll Milling Technique(John Wiley and Sons Inc., 2009) Seyhan, Abdullah Tuğrul; De La Vega, Alejandra; Tanoğlu, Metin; Schulte, KarlThis study aims to investigate the curing behavior of a vinyl ester-polyester resin suspensions containing 0.3 wt % of multiwalled carbon nanotubes with and without amine functional groups (MWCNTs and MWCNT-NH2). For this purpose, various analytical techniques, including Differential Scanning Calorimetry (DSC), Fourier infrared spectroscopy (FTIR), Raman Spectroscopy, and Thermo Gravimetric Analyzer (TGA) were conducted. The resin suspensions with carbon nanotubes (CNTs) were prepared via 3-roll milling technique. DSC measurements showed that resin suspensions containing CNTs exhibited higher heat of cure (Q), besides lower activation energy (Ea) when compared with neat resin. For the sake of simplicity of interpretation, FTIR investigations were performed on neat vinyl ester resin suspensions containing the same amount of CNTs as resin. As a result, the individual fractional conversion rates of styrene and vinyl ester were interestingly found to be altered dependent on MWCNTs and MWCNT-NH2. The findings obtained from RS measurements of the cured samples are highly proportional to those obtained from FTIR measurements. TGA measurements revealed that CNT modified nanocomposites have higher activation energy of degradation (Ed) compared with the cured polymer. The findings obtained revealed that CNTs with and without amine functional groups alter overall thermal curing response of the surrounding matrix resin, which may probably impart distinctive characteristics to mechanical behavior of the corresponding nanocomposites achieved.Article Citation - WoS: 38Citation - Scopus: 42Layered Clay/Epoxy Nanocomposites: Thermomechanical, Flame Retardancy, and Optical Properties(John Wiley and Sons Inc., 2008) Kaya, Elçin; Tanoğlu, Metin; Okur, SalihIn this study, layered clay/polymer nano-composites were developed based on epoxy resins and montmorillonite as the nanoplatelet reinforcement. Clay particles were treated with hexadecyltrimethylammonium chloride (HTCA) through an ion exchange reaction. In this way, Na+ interlay er cations of the clay is exchanged with onium cation of the surfactant that turns the hydrophilic clays (MMT) to organophilic (OMMT) characteristics. Thermal analysis results revealed that the glass transition temperature (Tg) and the dynamic mechanical properties including the storage and loss modulus of the neat epoxy resin increases by the incorporation of clay particles. It was also found that flame resistance of the polymer is improved by the addition of the clay particles.Article Citation - WoS: 11Citation - Scopus: 13Wind Speed Time Series Chacacterization Hy Hilbert Transform(John Wiley and Sons Inc., 2006) Alpay, Selda; Bilir, Levent; Özdemir, Serhan; Özerdem, BarışPredictions of wind energy potential in a given region are based on on-location observations. The time series of these observations would later be analysed and modelled either by a probability density function (pdf) such as a Weibull curve to represent the data or recently by soft computing techniques, such as neural networks (NNs). In this paper, discrete Hilbert transform has been applied to characterize the wind sample data measured on Izmir Institute of Technology campus area which is located in Urla, Izmir, Turkey, in March 2001 and 2002. By applying discrete Hilbert transform filter, the instantaneous amplitude, phase and frequency are found, and characterization of wind speed is acomplished. Authors have also tried to estimate the hourly wind data using daily sequence by Hilbert transform technique. Results are varying.Article Citation - WoS: 63Citation - Scopus: 77Artificial Neural Networks Applications in Building Energy Predictions and a Case Study for Tropical Climates(John Wiley and Sons Inc., 2005) Yalçıntaş, Melek; Akkurt, SedatThis study presents artificial neural network (ANN) methods in building energy use predictions. Applications of the ANN methods in energy audits and energy savings predictions due to building retrofits are emphasized. A generalized ANN model that can be applied to any building type with minor modifications would be a very useful tool for building engineers. ANN methods offer faster learning time, simplicity in analysis and adaptability to seasonal climate variations and changes in the building's energy use when compared to other statistical and simulation models. The model herein is presented for predicting chiller plant energy use in tropical climates with small seasonal and daily variations. It was successfully created based on both climatic and chiller data. The average absolute training error for the model was 9.7% while the testing error was 10.0%. This indicates that the model can successfully predict the particular chiller energy consumption in a tropical climate.Article Citation - WoS: 152Citation - Scopus: 172Experimental and Numerical Investigation of Thermal Energy Storage With a Finned Tube(John Wiley and Sons Inc., 2005) Erek, Aytunç; İlken, Zafer; Acar, Mehmet AliA latent heat thermal energy storage system using a phase change material (PCM) is an efficient way of storing or releasing a large amount of heat during melting or solidification. It has been determined that the shell-and-tube type heat exchanger is the most promising device as a latent heat system that requires high efficiency for a minimum volume. In this type of heat exchanger, the PCM fills the annular shell space around the finned tube while the heat transfer fluid flows within the tube. One of the methods used for increasing the rate of energy sto rage is to increase the heat transfer surface area by employing finned surfaces. In this study, energy storage by phase change around a radially finned tube is investigated numerically and experimentally. The solution of the system consists of the solving governing equations for the heat transfer fluid (HTF), pipe wall and phase change material. Numerical simulations are performed to investigate the effect of several fin parameters (fin spacing and fin diameter) and flow parameter (Re number and inlet temperature of HTF) and compare with experimental results. The effect of each variable on energy storage and amount of solidification are presented graphically.Article Citation - WoS: 67Citation - Scopus: 82Microhardness and Fracture Toughness of Dental Materials by Indentation Method(John Wiley and Sons Inc., 2005) Şakar-Deliormanlı, Aylin; Şakar Deliormanlı, Aylin Müyesser; Güden, Mustafa; Güden, MustafaThe main objective of this study was to measure the fracture toughness of the human teeth enamel using the microindentation technique and to compare the results calculated from the equations developed for Palmqvist and radial-median cracks. Vickers microhardness measurements of dental ceramic (alumina) and human teeth were performed using indentation fracture method. The fracture toughness of enamel was calculated using different equations reported in the literature. Vickers microhardness of the sintered alumina specimen (98.8% theoretical density) was measured to be 14.92 GPa under 9.8N indentation load. Three equations based on the radial-median cracks were found to be applicable for the fracture toughness determination of the enamel. Results show that indentation fracture method is adequate to measure microhardness and fracture toughness of dental materials. However the calculation of fracture toughness depended on the nature of the cracks and also on the location of the indentation. Therefore, it is necessary to identify the crack profile and to select the appropriate equation for accurate fracture toughness values.Article Citation - WoS: 37Citation - Scopus: 42Effects of Compaction Pressure and Particle Shape on the Porosity and Compression Mechanical Properties of Sintered Ti6al4v Powder Compacts for Hard Tissue Implantation(John Wiley and Sons Inc., 2007) Güden, Mustafa; Çelik, Emrah; Hızal, Alpay; Altındiş, Mustafa; Çetiner, SinanSintered Ti6Al4V powder compacts potentially to be used in implant applications were prepared using commercially available spherical and angular powders (100-200 mum) within the porosity range of 34-54%. Cylindrical green powder compacts were cold compacted at various pressures and then sintered at 1200 degrees C for 2 h. The final percent porosity and mean pore sizes were determined as functions of the applied compaction pressure and powder type. The mechanical properties were investigated through compression testing. Results have shown that yield strength of the powder compacts of 40-42% porosity was comparable with that of human cortical bone. As compared with previously investigated Ti powder compacts, Ti6Al4V powder compacts showed higher strength at similar porosity range. Microscopic observations on the failed compact samples revealed that failure occurred primarily by the separation of interparticle bond regions in the planes 45 degrees to the loading axis. Effects of compaction pressure and particle shape on the porosity and compression mechanical properties of sintered Ti6Al4V powder compacts for hard tissue implantation.