Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
8 results
Search Results
Article Citation - WoS: 9Citation - Scopus: 9Quasi-Static and High Strain Rate Properties of a Cross-Ply Metal Matrix Composite(Elsevier Ltd., 2009) Hall, Ian W.; Taşdemirci, Alper; Derrick, J.A series of compression tests has been carried out at quasi-static and high strain rates on cylindrical samples of an alumina fiber/Al-6061 metal matrix composite. The composite plates were prepared with fibers in the 0°, 0/90° and ±45° orientations. It was found that the mechanical properties were strongly dependent upon the imposed strain rate, with fracture stress increases of >50% being noted for several orientations at high strain rates: these increases are not believed to be related to strain rate sensitivity of either the matrix or fibers but to arise from the inertia of fragments which remain in place after fracture and continue to bear load. Also, and in contradiction to behavior anticipated from the rule of mixtures, it was found that 0/90° samples exhibited properties superior to those of 0° unidirectional samples. High-speed photography was used to confirm the sequence of deformation and fracture events at high strain rate. © 2008 Elsevier B.V. All rights reserved.Article Citation - WoS: 25Citation - Scopus: 28High Strain Rate Deformation Behavior of a Continuous Fiber Reinforced Aluminum Metal Matrix Composite(Elsevier Ltd., 2000) Güden, Mustafa; Hall, Ian W.An aluminum metal matrix composite reinforced with continuous unidirectional α-Al2O3 fibers has been compression tested at quasi-static and dynamic strain rates. In the transverse direction, the composite showed increased flow stress and maximum stress within the studied strain rate regime, 10−3 to 3500 s−1. The strain rate sensitivity of the flow stress in this direction was found to be similar to that of a similar, but unreinforced, alloy determined from previous work. In the longitudinal direction, the maximum stress of the composite increased with increasing strain rate within the range 10−5 to 700 s−1. The strain rate dependent maximum stress in this direction was described by the strain rate dependent fiber buckling stress.Article Citation - WoS: 19Citation - Scopus: 19Experimental Investigation of Interaction Effects in Foam-Filled Thin-Walled Aluminum Tubes(Springer Verlag, 2006) Güden, Mustafa; Toksoy, Ahmet Kaan; Kavi, HalitThe interaction coefficients of polystyrene foam filling of thin-walled aluminum cylindrical tubes were investigated experimentally through compression testing of partially foam-filled tubes with and without adhesive. The experimental load-displacement curves and observation of the crushed sections of filled tubes have shown that partial foam filling reduced the fold length and hence increased the average crushing loads of tubes, proving the interaction effect between tube wall and filler. The interaction coefficients for the partial foam filling were further calculated to be in the level and/or higher than that of the foam plateau load of transverse direction.Article Citation - WoS: 37Citation - Scopus: 42Effects of Compaction Pressure and Particle Shape on the Porosity and Compression Mechanical Properties of Sintered Ti6al4v Powder Compacts for Hard Tissue Implantation(John Wiley and Sons Inc., 2007) Güden, Mustafa; Çelik, Emrah; Hızal, Alpay; Altındiş, Mustafa; Çetiner, SinanSintered Ti6Al4V powder compacts potentially to be used in implant applications were prepared using commercially available spherical and angular powders (100-200 mum) within the porosity range of 34-54%. Cylindrical green powder compacts were cold compacted at various pressures and then sintered at 1200 degrees C for 2 h. The final percent porosity and mean pore sizes were determined as functions of the applied compaction pressure and powder type. The mechanical properties were investigated through compression testing. Results have shown that yield strength of the powder compacts of 40-42% porosity was comparable with that of human cortical bone. As compared with previously investigated Ti powder compacts, Ti6Al4V powder compacts showed higher strength at similar porosity range. Microscopic observations on the failed compact samples revealed that failure occurred primarily by the separation of interparticle bond regions in the planes 45 degrees to the loading axis. Effects of compaction pressure and particle shape on the porosity and compression mechanical properties of sintered Ti6Al4V powder compacts for hard tissue implantation.Article Citation - WoS: 19Citation - Scopus: 21Effect of Strain Rate on the Compressive Mechanical Behavior of a Continuous Alumina Fiber Reinforced Ze41a Magnesium Alloy Based Composite(Elsevier Ltd., 2006) Güden, Mustafa; Akil, Övünç; Taşdemirci, Alper; Çiftçioğlu, Muhsin; Hall, Ian W.The compressive mechanical response of an FP™ continuous fiber (35 vol.%) Mg composite has been determined in the transverse and longitudinal directions at quasi-static and high strain rates. It was found that the composite in the transverse direction exhibited strain rate sensitivity of the flow stress and maximum stress within the studied strain-rate range of 1.3 × 10−4 to 1550 s−1. The failure strain in this direction, however, decreased with increasing strain rate. Microscopic observations on the failed samples have shown that the composite failed by shear banding along the diagonal axis, 45° to the loading axis. Twinning was observed in the deformed cross-sections of the samples particularly in and near the shear band region. The strain rate sensitivity of the fracture stress of the composite in transverse direction is attributed to the matrix strain rate sensitivity. In the longitudinal direction, the composite failed by kink formation at quasi-static strain rates, while kinking and splitting were observed at the high strain rates. The maximum stress in the longitudinal direction was, however, found to be strain rate insensitive within the strain rate regime of 1.3 × 10−4 to 500 s−1. In this direction, similar to transverse direction, twinning was observed in the highly deformed kink region. Several different reasons are proposed for the strain rate insensitive compressive strength in this direction.Article Citation - WoS: 25Citation - Scopus: 36Effect of Strain Rate on the Compression Behaviour of a Woven Fabric S2-Glass Fiber Reinforced Vinyl Ester Composite(Elsevier, 2003) Akil, Övünç; Yıldırım, Uygar; Güden, Mustafa; Hall, Ian W.Quasi-static (~10−3s−1) and high strain rate (>500 s−1) compression behavior of an S2-glass woven fabric/vinyl ester composite plate was determined in the in-plane and through-thickness directions. In both directions, modulus and failure strength increased with increasing strain rate. A higher strain rate sensitive modulus was found in the through-thickness direction while a higher strain rate sensitive failure strength was found in the in-plane direction. In the in-plane direction, the failure mode was observed to change from splitting followed by “kink banding” (localized fiber buckling) to predominantly splitting at increasing strain rates, while it remained the same in the through-thickness direction.Article Citation - WoS: 26Citation - Scopus: 40Effect of Strain Rate on the Compression Behaviour of a Woven Glass Fiber/Sc-15 Composite(Elsevier Ltd., 2004) Güden, Mustafa; Yıldırım, Uygar; Hall, Ian W.Strain rate dependent compression behavior of a plain-weave S-2 glass fabric SC-15 epoxy (rubber toughened resin) composite plate, currently studied as the backing plate for composite armor applications, was determined in the through-thickness direction (normal to the fiber plane) in the strain rate regime of 1×10−4 to 1.1×103 s−1. In the studied strain rate regime, the modulus and failure strength of the composite were found to be rate sensitive and increased with increasing strain rate. Microscopic observations showed that the composite failed by ductile failure, involving matrix cracks and, later, cracking through and between the fiber layers. Crack deflections at rubber particle/matrix interface and particle pull-out were observed in the failed samples, contributing to the toughness of the composite.Article Citation - WoS: 24Citation - Scopus: 26Diatom Frustule-Filled Epoxy: Experimental and Numerical Study of the Quasi-Static and High Strain Rate Compression Behavior(Elsevier Ltd., 2008) Taşdemirci, Alper; Yüksel, Sinan; Karsu, Deniz; Gültürk, Elif; Hall, Ian W.; Güden, MustafaIn this study, centric type diatom frustules obtained from a diatomaceous earth filter material were used as filler in an epoxy resin with a weight percentage of 15% in order to assess the possible effects on the compressive behavior at quasi-static and high strain rates. The high strain rate testing of frustule-filled and neat epoxy samples was performed in a split-Hopkinson pressure bar (SHPB) set-up and modeled using the commercial explicit finite element code LS-DYNA 970. Result has shown that 15% frustule filling of epoxy increased both modulus and yield strength values at quasi-static and high strain rates without significantly reducing the failure strain. Microscopic observations revealed two main deformation modes: the debonding of the frustules from the epoxy and crushing/fracture of the frustules. The modeling results have further confirmed the attainment of stress equilibrium in the samples in SHPB testing following the initial elastic region and showed good agreement with the experimental stress–time response and deformation sequence of the samples in high strain rate testing.