Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
9 results
Search Results
Conference Object Development of Graphene Nanoplatelets Reinforced Aluminium Matrix Nanocomposites by a Combination of Semi-Solid Stirring and Ultrasonic Treatment(European Conference on Composite Materials, 2016) Kandemir, Sinan; Kandemir, Sinan; Aydoğan, Yücel; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyGraphene Nanoplatelets (GNPs) consisting of graphene layers with a thickness less than 100 nm have recently emerged as a promising reinforcement type owing to their excellent physical and mechanical properties to improve mechanical properties of alloys beyond ceramic nanoparticles. Although there are numerous studies on GNPs reinforced polymer matrix composites in the literature, the number of studies related to the incorporation of GNPs in metal matrices is limited. It is a challenging task to incorporate and uniformly distribute GNPs into liquid metals due to their poor wettability and large surface-to-volume ratio. The purpose of this study is to effectively disperse GNPs into liquid aluminium. 0.5 wt.% GNPs with an average thickness of 50-100 nm and size of 5 ?m were first incorporated into A360 aluminium alloy under semi-solid stirring, and then the composite was ultrasonically treated in fully liquid state. The microstructural investigation of the nanocomposites by optical and scanning electron microscopy may suggest that relatively uniform distribution and effective deagglomeration of GNPs in the matrix were achieved. The hardness of the GNPs reinforced nanocomposites increased in comparison with that of semi-solid stirred and ultrasonically processed A360 alloy without reinforcement, indicating the potential of GNPs for strengthening metals. © 2016, European Conference on Composite Materials, ECCM. All rights reserved.Conference Object The Shape and Size Effect of the Diatom Frustule Addition on the Compression Behavior of an Epoxy(Trans Tech Publications, 2018) Zeren, Doğuş; Kesici, Kutsal; Güden, Mustafa; Güden, Mustafa; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyThe effects of the Achnanthes Taeniata and the diatomaceous earth (diatomite) frustules addition on the compressive strength of an epoxy matrix were investigated experimentally. The Achnanthes Taeniata frustules having relatively high length/diameter aspect ratio (2-4) were isolated and cultured in laboratory. While the as-received commercial natural diatomite frustules were non-homogenous in shape and size. The filling epoxy matrix with ~6 wt% of commercial natural diatomite increased the compressive strength from 60 MPa to 67 MPa, while the Achnanthes Taeniata frustules addition increased to 79 MPa. The increased compressive strength and modulus of the the Achnanthes Taeniata frustules filled epoxy was attributed to the higher aspect ratio and relatively strong bonding with the epoxy matrix. The more effective load transfer from the matrix to the Achnanthes Taeniata frustules associated with the enhanced interface bonding was also proved microscopically. The frustules were observed to pull-out on the fracture surface of the Achnanthes Taeniata frustules filled epoxy.Article Citation - WoS: 8Citation - Scopus: 9The Increased Compression Strength of an Epoxy Resin With the Addition of Heat-Treated Natural Nano-Structured Diatom Frustules(SAGE Publications Inc., 2017) Zeren, Doğuş; Güden, Mustafa; Güden, Mustafa; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyNatural diatom frustules composing nanometer size silica particles were heat-treated at temperatures between 600 and 1200℃ for 2 h and used as filler/reinforcing agent (15 wt%) in an epoxy resin. The opal structure of as-received natural diatom frustules was transformed into cristobalite after the heat-treatment above 900℃. The epoxy resin test samples reinforced with heat-treated and as-received frustules and neat epoxy test samples were compression tested at the quasi-static strain rate of 7 × 10−3 s−1. The results showed that the inclusion of the frustules heat-treated at 1000℃ increased the compressive yield strength of the resin by 50%, while the addition of the diatom frustules heat-treated above and below 1000℃ and the as-received frustules increased the strength by ∼25% and 16%, respectively. The heat treatment above 1000℃ decreased the surface area of the frustules from 8.23 m2 g−1 to 3.46 m2 g−1. The cristobalite grains of the frustules heat-treated at 1000℃ was smaller than 100 nm, while the grain size increased to ∼500 nm at 1200℃. The increased compressive stresses of the resin at the specific heat treatment temperature (1000℃) were ascribed to nano size crystalline cristobalite grains. The relatively lower compressive stresses of the epoxy resin filled with frustules heat-treated above 1000℃ were attributed to the micro-cracking of the frustules that might be resulted from higher density of the cristobalite than that of the opal and accompanying reduction of the surface area and the surface pore sizes that might impair the resin-frustule interlocking and intrusion.Conference Object Microstructure-Performance Relation in Pmma-Based Open-Cell Porous Materials for High Pressure Ceramic Sanitaryware Casting(Trans Tech Publications, 2004) Ergün, Yelda; Dirier, C.; Tanoğlu, Metin; Tokman, C.; Tanoğlu, Metin; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyThe ceramic whiteware/sanitaryware industry is rapidly undergoing to implement high-pressure casting techniques for ceramic article production. In these techniques, materials with open pore microstructure that allows drainage of water under applied pressure are needed. The polymethyl methacrylate (PMMA) based polymeric porous materials have become the most suitable type of materials for this purpose because of their short casting periods and high service lives. However, the superior service life and performance of these materials are closely related to the microstructure. In the present study, the porous materials with various compositions of the constituents in the emulsion were produced to effect the microstructure of PMMA-based materials. The variations on the pore microstructure were interrelated to the performance of the material for high-pressure sanitaryware casting. The pore morphology and water permeability of the samples was measured using optical and SEM microscopy and permeability measurement techniques, respectively. The compressive collapse stress and modulus values were determined by performing compression testing. The results showed a significant interrelation between microstructure and the performance of the PMMA-based ceramic mould materials.Article Citation - WoS: 54Citation - Scopus: 62Sic-Particulate Aluminum Composite Foams Produced by Powder Compacts: Foaming and Compression Behavior(Springer Verlag, 2003) Elbir, Semih; Yılmaz, Selahattin; Güden, Mustafa; Güden, Mustafa; Hall, Ian W.; Yılmaz, Selahattin; 03.02. Department of Chemical Engineering; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyThe foaming behavior of SiC-particulate (8.6% by volume) aluminum composite powder compacts contained Titanium Hydride blowing agent was investigated by heating above the melting temperature (750°C) in a pre-heated furnace. Aluminum powder compacts were also prepared and foamed using similar compaction and foaming parameters in order to determine the effect of SiC-particulate addition on foaming and compression behavior. The linear expansions of the compacts at various furnace holding times were ex situ determined. Optical and scanning electron microscopy techniques were used to characterize prepared and deformed foams microstructures. The SiC-particulate addition was found to increase the linear expansion and reduce the extent of the liquid metal drainage and cell coarsening of the aluminum compacts. The composite foam samples also showed higher compressive stresses, but a more brittle behavior as compared with aluminum foams.Article Citation - WoS: 22Citation - Scopus: 28Mechanical Interlocking Between Porous Electrospun Polystyrene Fibers and an Epoxy Matrix(American Chemical Society, 2014) Demir, Mustafa Muammer; Horzum, Nesrin; Taşdemirci, Alper; Turan, Ali Kıvanç; Güden, Mustafa; Güden, Mustafa; Demir, Mustafa Muammer; 03.10. Department of Mechanical Engineering; 03.09. Department of Materials Science and Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyAn epoxy matrix filled with nonwoven mats of porous polystyrene (PS) fibers processed by an electrospinning was compression tested at quasi-static (1 × 10–3 s–1) and high strain (315 s–1) rates. The electrospun PS fibers with a diameter between 6 and 9 μm, accommodated spherical pores on the surface with the sizes ranging from 0.1 to 0.2 μm. The filling epoxy matrix with 0.2 wt % PS fibers increased the compressive elastic modulus and compressive strength over those of neat epoxy resin. The microscopic observations indicated that the surface pores facilitated the resin intrusions into the fiber, enhancing the interlocking between resin and fibers, and increased the deformation energy expenditure of the polymer matrix.Article Citation - WoS: 60Citation - Scopus: 70Foam Glass Processing Using a Polishing Glass Powder Residue(Elsevier Ltd., 2013) Attila, Yiğit; Güden, Mustafa; Taşdemirci, Alper; Taşdemirci, Alper; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyThe foaming behavior of a powder residue/waste of a soda-lime window glass polishing facility was investigated at the temperatures between 700 and 950 °C. The results showed that the foaming of the glass powder started at a characteristic temperature between 670 and 680 °C. The maximum volume expansions of the glass powder and the density of the foams varied between 600% and 750% and 0.206 and 0.378 g cm−3, respectively. The expansion of the studied glass powder residue resulted from the decomposition of the organic compounds on the surfaces of the glass powder particles, derived from an oil-based coolant used in the polishing. The collapse stress of the foams ranged between ∼1 and 4 MPa and the thermal conductivity between 0.048 and 0.079 W K−1 m−1. Both the collapse stress and thermal conductivity increased with increasing the foam density. The foams showed the characteristics of the compression deformation of the open cell brittle foams, which was attributed to the relatively thick cell edges.Article Citation - WoS: 12Citation - Scopus: 15Morphological and Molecular Identification of Pennate Diatoms Isolated From Urla, Izmir, Coast of the Aegean Sea(TUBITAK, 2013) Kesici, Kutsal; Tüney, İnci; Güden, Mustafa; Zeren, Doğuş; Güden, Mustafa; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyDiatoms represent an important class of aquatic phototrophs. They are not only one of the major contributors to global carbon fixation, but also play a key role in the biogeochemical cycling of silica. Molecular identification methods based on conserved DNA sequences, such as ITS (Internal Transcribed Spacer) have revolutionized our knowledge and understanding of conventional taxonomy. In this study, we aimed to compare the conventional identification methods with molecular identification methods. To do so, we isolated four diatom samples from Coast of Urla and characterized them using light microscopy (LM) and scanning electron microscopy (SEM) according to morphological features. Then, we amplified ITS regions using conventional polymerase chain reaction (PCR), sequenced the PCR products and analyzed the sequences using bioinformatic tools. Bioinformatic analysis indicated that the isolated species had high sequence similarity to Pseudo-nitzschia sp., Achnanthes sp., Amphora sp. and Cylindrotheca sp. We believe that molecular identification methods enable rapid and more reliable identification of diatom species and are crucial for monitoring harmful algal blooms.Article Citation - WoS: 10Citation - Scopus: 10Open Cell Lead Foams: Processing, Microstructure, and Mechanical Properties(Springer Verlag, 2012) Savacı, Umut; Yılmaz, Sinan; Güden, Mustafa; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyOpen cell lead foams with the porosities between 48 and 74 % were prepared by means of powder metallurgical and casting routes, using ammonium bicarbonate particles, silica beads, and sodium chloride salt particles as space holder. The resulting foam samples structure closely resembled open cell foam structure: each cell had few interconnections with neighboring cells. Small-sized lead (II) fluoride precipitates were microscopically observed in the interior of cells in the foam samples prepared using silica beads as space holder, resulting from the reaction between silica and hydrofluoric acid in the space holder dissolution step. The compression stress–strain curve of foam samples prepared by powder metallurgical route showed brittle deformation behavior following the initial elastic deformation region, while the foam samples prepared by casting route showed characteristic foam deformation behavior: cell edge crushing on the bent cell walls, and cell wall tearing. The collapse stresses, densification strains, and elastic moduli of the prepared foams were further fitted with scaling relations.