Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
489 results
Filters
Settings
Search Results
Conference Object Determination of Interfacial Heat Transfer Coefficient for a Mixed Convection Heat Transfer in a Vertical Channel Filled With Uniformly Heated Blocks(Begell House Inc., 2015) Çelik, Hasan; Mobedi, Moghtada; Manca,O.; Buonomo,B.The interfacial convective heat transfer coefficient of a periodic porous medium under mixed convection heat transfer is determined computationally by using volume averaging method. The porous medium consists of square blocks in inline arrangement. The continuity, momentum and energy equations are solved in dimensionless form for a representative elementary volume of porous medium and the velocity and temperature fields for different values of Richardson and Reynolds numbers are obtained. Based on the obtained results, the interfacial convective heat transfer coefficient is calculated by using volume average method. The temperature of the solid phase is considered uniform and different than the inlet temperature. A detailed discussion on the effect of the governing dimensionless parameters (i.e. Reynolds, Richardson numbers, and porosity) on the local and average interfacial Nusselt number is done. It is concluded that the local interfacial convective heat transfer coefficient increases with Reynolds number, however the rate of increase depends on Richardson number and porosity. The study is performed for two values of porosity of 0.51 and 0.94. © 2021, Begell House Inc. All rights reserved.Conference Object A Numerical Study on the Determination of the Effects of Pore To Throat Size Ratio on the Thermal Dispersion in Porous Media(Begell House, 2014) Özgümüş, Türküler; Mobedi, Moghtada; Özkol, ÜnverDirect pore-level numerical simulations are widely used to estimate macroscopic properties of fluid flow and heat transfer in porous media. Thermal dispersion is one of the most important macroscopic transport parameters for analyzing convective heat transfer in a porous medium. It should be known in order to predict the macroscopic temperature distribution. In the present study, a microscopic scale analysis is performed for a porous medium with periodic structure. A representative elementary volume is chosen from an infinite medium consists of rectangular rods in inline arrangement. The continuity and momentum equations are solved to obtain flow field and the energy equations for fluid and solid phases are solved to obtain microscopic temperature distributions in two phases. There are velocity and temperature deviations between macroscopic and microscopic local values. Volume averaging method is applied to the computed deviations and thermal dispersion conductivity of porous media is determined. The aim of this study is to analyze the effects of pore to throat size ratio on the longitudinal and transverse thermal dispersion in porous media. The study is performed for representative elementary volumes with different pore to throat size ratios and Reynolds numbers from 1 to 100. The study is performed for high porosity porous media (ε = 0.7 and 0.91). It is shown that the porosity and pore to throat size ratio have more influence on the transverse rather than longitudinal thermal dispersion. © 2014, Begell House Inc. All rights reserved.Conference Object Mechanisms, Transmissions and Applications(Springer, 2018) Dede, Mehmet İsmet Can; İtik, Mehmet; Lovasz, Erwin-Christian; Kiper, GökhanThis volume contains the proceedings of MeTrApp 2017, the 4th Conference on Mechanisms, Transmissions and Applications, that was held in Trabzon, Turkey, July 3-5, 2017. The topics treated in this volume are Mechanism Design, Parallel Manipulators, Control Applications, Mechanical Transmissions, Cam Mechanisms, and Dynamics of Machinery. The conference was organised by the IFToMM Technical Committees for “Linkages and Mechanical Controls” and “Gearing and Transmissions” under the patronage of the IFToMM and sponsorship of Karadeniz Technical University, Izmir Institute of Technology and IFToMM Turkey (MAKTED). The aim of the conference was to bring together researchers, scientists, industry experts and students to provide, in a friendly and stimulating environment, the opportunity to exchange know-how and promote collaboration in the field of Mechanism and Machine Science.Article Citation - WoS: 1Citation - Scopus: 2Emergence of Taperedducts in Vascular Designs With Laminar and Turbulent Flows(Begell House, 2014) Çetkin, ErdalHere we show that tapered ducts emerge in volumetrically bathed porous materials to decrease the resistance to the flow in laminar and turbulent flow regimes. The fluid enters the volume from one point and it is distributed to the entire volume. After bathing the volume, it is collected and leaves the volume from another point, i.e., two trees matched canopy to canopy. This paper shows that the flow architecture (i.e., design of the void spaces in a porous material) should be changed to obtain the minimum resistance to the flow as its size increases. Tapering the ducts decreases the order of the transition size, i.e., the size for changing from one construct to another to obtain the minimum pressure drop. The decrease in the pressure drop is 16% and 38% with the tapered ducts when the flow is laminar and turbulent, respectively. In addition, the volume ratios and the shape of the tapered ducts are documented. There is no design existing in nature with diameters of constant size in order to distribute and/or collect heat, fluid, and/or stress such as bones, rivers, veins, and tree branches. The emergence of the tapered ducts in designed porous materials is natural.Article Citation - WoS: 21Citation - Scopus: 22Daily Application of Low Magnitude Mechanical Stimulus Inhibits the Growth of Mda-Mb Breast Cancer Cells in Vitro(BioMed Central Ltd., 2014) Ölçüm, Melis; Özçivici, EnginIntroduction: Mechanical loads can regulate cell proliferation and differentiation at various stages of development and homeostasis. However, the extension of this regulatory effect of mechanical loads on cancer cells is largely unknown. Increased physical compliance is one of the key features of cancer cells, which may hamper the transmission of mechanical loads to these cells within tumor microenvironment. Here we tested whether brief daily application of an external low magnitude mechanical stimulus (LMMS), would impede the growth of MDA-MB-231 aggressive type breast cancer cells in vitro for 3 wks of growth. Methods: The signal was applied in oscillatory form at 90 Hz and 0.15 g, a regimen that would induce mechanical loads on MDA-MB-231 cells via inertial properties of cells rather than matrix deformations. Experimental cells were exposed to LMMS 15 min/day, 5 days/week in ambient conditions while control cells were sham loaded. Cell proliferation, viability, cycle, apoptosis, morphology and migration were tested via Trypan Blue dye exclusion, MTT, PI, Annexin V, Calcein-AM and phalloidin stains and scratch wound assays. Results: Compared to sham controls, daily application of LMMS reduced the number and viability of cancerous MDA-MB-231 cells significantly after first week in the culture, while non-cancerous MCF10A cells were found to be unaffected. Flow cytomety analyses suggested that the observed decrease for the cancer cells in the LMMS group was due to a cell cycle arrest rather than apoptosis. LMMS further reduced cancer cell circularity and increased cytoskeletal actin in MDA-MB-231 cells. Conclusion: Combined, results suggest that direct application of mechanical loads negatively regulate the proliferation of aggressive type cancer cells. If confirmed, this non-invasive approach may be integrated to the efforts for the prevention and/or treatment of cancer.Article Citation - WoS: 12Citation - Scopus: 11Inverted Fins for Cooling of a Non-Uniformly Heated Domain(Yıldız Teknik Üniversitesi, 2015) Çetkin, ErdalThis paper shows that the peak temperature of a non-uniformly heated region can be decreased by embedding high-conductivity tree-shaped inserts which is in contact with a heat sink from its stem. The volume fraction of the high-conductivity material is fixed, and so is the volume of the solid region. The length scale of the solid domain is L. Inside there is a cube-shaped region with length scale of 0.1L and heat production 100 times greater than the rest of the domain. The location of this hot spot was varied to uncover how its location affects the peak temperature and the design of inverted fins, i.e. highconductivity tree-shaped inserts. The volume fraction of the high-conductivity tree was varied for number of bifurcation levels of 0, 1 and 2. This showed that increasing the number of the bifurcation levels decreases the peak temperature when the volume fraction decreases. The optimal diameter ratios and optimal bifurcation angles at the each junction level are also documented. Y-shaped trees promise smaller peak temperatures than T-shaped trees. The location of the vascular tree in the z direction also affects the peak temperature when the heat generation is non-uniform. In addition, the peak temperature is minimum when z = 0.65L even though the hot spot is located on z = 0.75L.Article Citation - WoS: 8Citation - Scopus: 8Free Vibration Analysis of Damaged Composite Beams(Techno Press, 2015) Cünedioğlu, Yusuf; Beylergil, BertanIn this study, free vibration analyses of symmetric laminated cantilever and simply supported damaged composite beams are investigated by using finite element method (FEM). Free vibration responses of damaged beams are examined using Euler Bernoulli beam and classical lamination theories. A computer code is developed by using MATLAB software to determine the natural frequencies of a damaged beam. The local damage zone is assumed to be on the surface lamina of the beam by broken fibers after impact. The damaged zone is modeled as a unidirectional discontinuous lamina with 0 degrees orientations in this study. Fiber volume fraction (v(f)), fiber aspect ratio (L-f/d(f)), damage length (L-D) and its location (lambda/L), fiber orientation and stacking sequence parameters effects on natural frequencies are investigated. These parameters are affected the natural frequency values significantly.Article The Effect of Time Delay of Fluid Flow in a Vascularized Plate(MIM Research Group, 2018) Yenigün, Onur; Coşkun, Turgay; Çetkin, ErdalIn this study, we show the effect of time delay of coolant fluid flow into a vascularized plate on the peak temperature. Coolant flows along vascular channels which were embedded in a rectangular plate. Two kinds of vascular channel designs were investigated experimentally: parallel and tree-shaped. In the study, the peak temperatures were monitored and the coolant was pumped when the peak temperature reaches to 50°C, 70°C and 90°C. The performance comparison of two distinct designs is based on two criteria: the time required for the steady state condition after the coolant is pumped and the peak temperature after the steady state condition is conformed. The results show that the time required to reach steady-state condition increases as the time delay increases. The parallel and tree-shaped designs show similar performance (time required to reach steady state) with slightly improved performance in the tree-shaped design as the preset temperature for time delay increases. For instance, 4% decrease in the time required to reach steady-state with the tree-shaped design relative to the parallel design was achieved when the preset temperature for time delay is 90°C.Article Optimum Design of Anti-Buckling Behavior of Graphite/Epoxy Laminated Composites by Differential Evolution and Simulated Annealing Method(MIM Research Group, 2019) Akçaır, Mehmet; Savran, Melih; Aydın, Levent; Ayakdaş, Ozan; Öztürk, Savaş; Küçükdoğan, NilayStacking sequence design and optimization of 64 layered symmetric-balance graphite/epoxy laminated composite have been performed. The optimization problems aim to find the optimum stacking sequence maximizing the critical buckling load by single objective optimization approach. Differential Evolution (DE) and Simulated Annealing (SA) optimization algorithms are proposed to solve the problems. The effect of the aspect ratios (a/b) and in-plane biaxial compressive loading ratios (Nx/Ny) on critical buckling load are investigated. In order to see the effect of discrete increments of fiber orientation angle on critical buckling load, 1°, 5°, 15°, 30° and 45° fiber angle increments are also considered. The results show that (i) the proposed algorithms DE and SA exhibit comparable performance in terms of critical buckling load when compared Genetic algorithm (GA) and Generalized pattern search algorithm (GPSA), (ii) DE and SA find distinct stacking sequence configurations in terms of buckling load for the same laminated structure design problems.Article Casting the Swarms Problem in the Ensembles Context(Çukurova Üniversitesi, 2016) Kok, Çağatay; Çellek, Seven Burçin; Koşun, Çağlar; Özdemir, SerhanSürü robotları yüzlerce farklı şekilde modellenmiştir. Kalabalık olmaları sürülerin bir özelliğidir. Sayılamayacak kadar çok sayıya ulaştıklarında, termo-istatiksel mekanik devreye girebilir. Yazarlar bu avantajı kullanarak sürü robotları için evrensel istatistik oluşturmak istediler. Üç temel topluluk açıklandı ve formüle edildi. Sürüler izole edildiklerinde mikrokanonik uyum ortama hakim olurken, ortama av veya avcı girişi olur ise, duruma bağlı olarak değişimler gözlemlenir. Bu yüzden formulasyonlar ve geçişler şarta bağlıdır. Son olarak gözlemlenen olasılıklar tartışıldı