Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
3 results
Search Results
Article Citation - WoS: 1Citation - Scopus: 1Analysis and Comparison of the Projectile Impact Response of an Electron Beam Melt-Ti64 Body Centered Cubic Lattice-Cored Sandwich Plate(Springer, 2025) Güden, Mustafa; Çimen, G.; Yıldıztekin, F.M.; Güden, M.; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of TechnologyBackground: One potential application of additively fabricated lattice structures is in the blade containment rings of gas turbine engines. The blade containment rings are expected to be able to absorb the kinetic energy of a released blade (broken blade) in order to protect the engine parts from damaging. Metallic lattice-cored sandwich plates provide a gap (free space) between two face sheets, which helps to arrest the released blade and increases the energy absorption capability of containment rings. Objective: The objective was to investigate numerically the projectile impact response of Body-Centered-Cubic (BCC) Electron-Beam-Melt (EBM) lattice-cored/Ti64 face sheet sandwich plates as compared with that of an equal-mass monolithic EBM-Ti64 plate. Methods: The projectile impact simulations were implemented in LS-DYNA using the previously determined flow stress and damage models and a spherical steel impactor at the velocities ranging from 150 to 500 m s−1. The experimental projectile impact tests on the monolithic plate were performed at two different impact velocities and the results were used to confirm the validity of the used flow stress and damage models for the monolithic plate models. Results: Lower impact stresses were found numerically in the sandwich plate as compared with the monolithic plate at the same impact velocity. The bending and multi-cracking of the struts over a wide area in the sandwich plate increased the energy absorption and resulted in the arrest of the projectile at relatively high velocities. While monolithic plate exhibited a local bent area, resulting in the development of high tensile stresses and the projectile perforations at lower velocities. Conclusions: The numerical impact stresses in the sandwich plate were distributed over a wider area around the projectile, leading to the fracture and bending of many individual struts which significantly increased the resistance to the perforation. Hence, the investigated lattice cell topology and cell, strut, and face sheet sizes and the lattice-cored sandwich plate was shown potentially more successful in stopping the projectiles than the equal-mass monolithic plates. © The Author(s) 2025.Article Citation - WoS: 2Citation - Scopus: 3Design and Manufacturing of a Hip Joint Motion Simulator With a Novel Modular Design Approach(Springer, 2024) Mihçin, Şenay; Mihçin, D.Ş.; Lazoglu, I.; 01. Izmir Institute of Technology; 03.10. Department of Mechanical Engineering; 03. Faculty of EngineeringThe study is aimed to develop a hip joint wear simulator using a modular design approach to help experimentally monitor and control critical wear parameters to validate in-silico wear models. The proper control and application of wear parameters such as the range of motion, and the applied force values while estimating the lost material due to wear are essential for thorough analysis of wear phenomena for artificial joints. The simulator's dynamics were first modeled, then dynamic loading data was used to calculate the forces, which were further used for topology optimization to reduce the forces acting on each joint. The reduction of the link weights, connected to the actuators, intends to improve the quality of motion transferred to the femoral head. The modular design approach enables topology-optimized geometry, associated gravitational and dynamic forces, resulting in a cost-effective, energy-efficient product. Moreover, this design allows integration of the subject specific data by allowing different boundary conditions following the requirements of industry 5.0. Overall, the in-vitro motion stimulations of the hip-joint prosthesis and the modular design approach used in the study might help improve the accuracy and the effectiveness of wear simulations, which could lead into the development of better and longer-lasting joint prostheses for all. The subject-specific and society-based daily life data implemented as boundary conditions enable inclusion of the personalized effects. Next, with the results of the simulator, CEN Workshop Agreement (CWA) application is intended to cover the personalized effects for previously excluded populations, providing solution to inclusive design for all. © 2023, The Author(s), under exclusive licence to Springer-Verlag France SAS, part of Springer Nature.Article Citation - WoS: 9Citation - Scopus: 11Experimental Investigation of Spray Characteristics of Ethyl Esters in a Constant Volume Chamber(Springer, 2024) Yıldız, Güray; Özkol, Ünver; Rodriguez, Alvaro Diez; Rodriguez, A.D.; 01. Izmir Institute of Technology; 03.06. Department of Energy Systems Engineering; 03.10. Department of Mechanical Engineering; 03. Faculty of EngineeringAbstract: Biodiesels are mainly produced via the utilization of methanol in transesterification, which is the widespread biodiesel production process. The majority of this methanol is currently obtained from fossil resources, i.e. coal and natural gas. However, in contrast with methanol, biomass-based ethanol can also be used to produce biodiesels; this could allow the production line to become fully renewable. This study aimed to investigate the spray characteristics of various ethyl ester type biodiesels derived from sunflower and corn oils in comparison to methyl esters based on the same feedstocks and reference petroleum-based diesel. Spray penetration length (SPL) and spray cone angle (SCA) were experimentally evaluated in a constant volume chamber allowing optical access, under chamber pressures of 0, 5, 10 and 15 bar and injection pressures of 600 and 800 bar. Sauter mean diameter (SMD) values were estimated by using an analytical correlation. Consequently, ethyl esters performed longer SPL (2.8–20%) and narrower SCA (5.1–19%) than diesel under ambient pressures of 5 and 10 bar. Although the SMD values of ethyl esters were 48% higher than diesel on average, their macroscopic spray characteristics were very similar to those of diesel under 15 bar chamber pressure. Moreover, ethyl esters were found to be very similar to methyl esters in terms of spray characteristics. The differences in SPL, SCA and SMD values for both types of biodiesels were lower than 4%. When considering the uncertainty (± 0.84%) and repeatability (±5%) ratios, the difference between the spray characteristics of methyl and ethyl esters was not major. Graphical abstract: [Figure not available: see fulltext.] © 2022, The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.