Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
4 results
Search Results
Article Citation - WoS: 13Citation - Scopus: 16Influence of Recycled Carbon Fiber Addition on the Microstructure and Creep Response of Extruded Az91 Magnesium Alloy(KeAi Communications Co., 2023) Kandemir, Sinan; Bohlen, Jan; Dieringa, HajoIn this study, the recycled short carbon fiber (CF)-reinforced magnesium matrix composites were fabricated using a combination of stir casting and hot extrusion. The objective was to investigate the impact of CF content (2.5 and 5.0 wt.%) and fiber length (100 and 500 µm) on the microstructure, mechanical properties, and creep behavior of AZ91 alloy matrix. The microstructural analysis revealed that the CFs aligned in the extrusion direction resulted in grain and intermetallic refinement within the alloy. In comparison to the unreinforced AZ91 alloy, the composites with 2.5 wt.% CF exhibited an increase in hardness by 16–20% and yield strength by 5–15%, depending on the fiber length, while experiencing a reduction in ductility. When the reinforcement content was increased from 2.5 to 5.0 wt.%, strength values exhibited fluctuations and decline, accompanied by decreased ductility. These divergent outcomes were discussed in relation to fiber length, clustering tendency due to higher reinforcement content, and the presence of interfacial products with micro-cracks at the CF-matrix interface. Tensile creep tests indicated that CFs did not enhance the creep resistance of extruded AZ91 alloy, suggesting that grain boundary sliding is likely the dominant deformation mechanism during creep. © 2023Article Citation - WoS: 41Citation - Scopus: 45High Temperature Tensile, Compression and Creep Behavior of Recycled Short Carbon Fibre Reinforced Az91 Magnesium Alloy Fabricated by a High Shearing Dispersion Technique(National Engineering Research Center for Magnesium Alloys of China, Chongqing University, 2021) Kandemir, Sinan; Gavras, Sarkis; Dieringa, HajoThe present study seeks the feasibility of using short carbon fibres recycled from polymer matrix composites as alternative to virgin carbon fibres in the reinforcement of magnesium alloys. The microstructures, high temperature mechanical and creep properties of AZ91 alloy and its composites with various recycled carbon fibre contents (2.5 and 5 wt.%) and lengths (100 and 500 ?m) were investigated in the temperature range of 25–200 °C. The microstructural characterization showed that the high shear dispersion technique provided the cast composites with finer grains and relatively homogenous distribution of fibres. The materials tested displayed different behaviour depending on the type of loading. In general, while enhancements in the mechanical properties of composites is attributed to the load bearing and grain refinement effects of fibres, the fluctuations in the properties were discussed on the basis of porosity formation, relatively high reinforcement content leading to fibre clustering and interlayer found between the matrix and reinforcement compared to those of AZ91 alloy. The compressive creep tests revealed similar or higher minimum creep rates in the recycled carbon fibre reinforced AZ91 in comparison to the unreinforced AZ91. © 2021Article Citation - WoS: 4Citation - Scopus: 5Effects of Tib2 Nanoparticle Content on the Microstructure and Mechanical Properties of Aluminum Matrix Nanocomposites(Walter de Gruyter GmbH, 2017) Kandemir, SinanThe present work reports the fabrication of A357 alloy matrix nanocomposites reinforced with 0.5, 1.0 and 2.0 wt.-% TiB2 nanoparticles (20-30 nm) by a novel method which is the combination of semi-solid mechanical mixing and ultrasonic dispersion of nanoparticles in liquid state. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicated that reasonably effective deagglomeration and uniform distribution of TiB2 nanoparticles into the matrix were achieved. Transmission electron microscopy studies also confirmed that the nanoparticles were embedded into the matrix and a good bonding was obtained between the matrix and the reinforcement. Increasing nanoparticle content led to grain refinement and significant enhancement in the mechanical properties of nanocomposites. The addition of 0.5, 1.0, and 2.0 wt.-% TiB2 nanoparticles increased the 0.2 % proof stress of matrix alloy by approximately 31, 48 and 61 %, respectively. The contribution of different mechanisms to the strength enhancement is discussed. It is proposed that the strengthening is mainly due to Orowan mechanism and dislocation generation effect by the coefficient of thermal expansion mismatch between the TiB2 nanoparticles and the matrix.Article Citation - WoS: 14Citation - Scopus: 16Microstructure and Mechanical Properties of A357/Sic Nanocomposites Fabricated by Ultrasonic Cavitation-Based Dispersion of Ball-Milled Nanoparticles(SAGE Publications Inc., 2017) Kandemir, SinanIn this work, A357/0.5 wt.% SiC nanocomposites were fabricated with a combination of ultrasonic processing and a nanoparticle feeding mechanism that involves the introduction of a closed end aluminium tube filled with the ball-milled SiC nanoparticles (20-30 nm) and aluminium powders (<75 μm) into the melt for complete deagglomeration and uniform dispersion of nanoparticles through the matrix. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicate that relatively effective deagglomeration and uniform dispersion of SiC nanoparticles into the molten alloy were achieved. The hardness and tensile properties of the nanocomposites were notably improved compared to those of the ultrasonically processed A357 alloy without reinforcement, showing the strengthening potency of nanoparticles and the good bonding obtained at the particle-reinforcement interface.