Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
4 results
Search Results
Article Citation - WoS: 6Citation - Scopus: 6The Expansion Behavior of Slurries Containing Recycled Glass Powder Carboxymethyl Cellulose, Lime and Aluminum Powder(Elsevier, 2020) Zeren, Doğuş; Şentürk, Ufuk; Güden, MustafaThe rheology and foaming/expansion of the slurries of a waste/recycled glass powder with 50, 55 and 60 wt% of solid (glass powder) were experimentally investigated. The glass powder slurries were foamed using aluminum powder as foaming agent (0.75 wt%) and calcium hydroxide as activator (1 wt%). Sodium carboxymethyl cellulose (CMC) was added to the slurries as a binder with the amounts between 0 and 4 wt%. The expansions of the slurries were measured in-situ using a laser sensor and reported as percent volume expansion. The CMC-addition increased the viscosities of the slurries, particularly the fine size powder slurries. The slurries with the relatively low-viscosity exhibited lower initial expansion rates compared to the slurries with the relatively high-viscosity. The maximum expansions of the slurries increased from 300 to 350%, when the viscosity increased to 5 Pa s and reached a steady value around 400% between 5 and 50 Pa s. The expansions of the slurries could not be achieved above 50 Pa s since they became too thick to be foamed. The foam samples made from the slurries with 55 and 60 wt% of solid and sintered at 700 and 750 degrees C for 30 min had the average densities between 355 and 530 kg m(-3) and the average compressive strengths between 0.2 and 0.5 MPa. Increasing sintering time to 60 min at 750 degrees C increased the average compressive strength from 0.5 to 1.5 MPa for the foam samples made from the slurry with 60 wt% of solid. These proved that both sintering temperature and time were effective in increasing the compressive strengths of the foamed structures. The thermal conductivities of the sintered foam samples with the densities of 355 and 504 kg m(-3) were measured 0.042 and 0.057 W m(-1) K-1, respectively. (C) 2019 Elsevier Ltd. All rights reserved.Conference Object The Shape and Size Effect of the Diatom Frustule Addition on the Compression Behavior of an Epoxy(Trans Tech Publications, 2018) Zeren, Doğuş; Kesici, Kutsal; Sukatar, Atakan; Güden, MustafaThe effects of the Achnanthes Taeniata and the diatomaceous earth (diatomite) frustules addition on the compressive strength of an epoxy matrix were investigated experimentally. The Achnanthes Taeniata frustules having relatively high length/diameter aspect ratio (2-4) were isolated and cultured in laboratory. While the as-received commercial natural diatomite frustules were non-homogenous in shape and size. The filling epoxy matrix with ~6 wt% of commercial natural diatomite increased the compressive strength from 60 MPa to 67 MPa, while the Achnanthes Taeniata frustules addition increased to 79 MPa. The increased compressive strength and modulus of the the Achnanthes Taeniata frustules filled epoxy was attributed to the higher aspect ratio and relatively strong bonding with the epoxy matrix. The more effective load transfer from the matrix to the Achnanthes Taeniata frustules associated with the enhanced interface bonding was also proved microscopically. The frustules were observed to pull-out on the fracture surface of the Achnanthes Taeniata frustules filled epoxy.Article Citation - WoS: 8Citation - Scopus: 9The Increased Compression Strength of an Epoxy Resin With the Addition of Heat-Treated Natural Nano-Structured Diatom Frustules(SAGE Publications Inc., 2017) Zeren, Doğuş; Güden, MustafaNatural diatom frustules composing nanometer size silica particles were heat-treated at temperatures between 600 and 1200℃ for 2 h and used as filler/reinforcing agent (15 wt%) in an epoxy resin. The opal structure of as-received natural diatom frustules was transformed into cristobalite after the heat-treatment above 900℃. The epoxy resin test samples reinforced with heat-treated and as-received frustules and neat epoxy test samples were compression tested at the quasi-static strain rate of 7 × 10−3 s−1. The results showed that the inclusion of the frustules heat-treated at 1000℃ increased the compressive yield strength of the resin by 50%, while the addition of the diatom frustules heat-treated above and below 1000℃ and the as-received frustules increased the strength by ∼25% and 16%, respectively. The heat treatment above 1000℃ decreased the surface area of the frustules from 8.23 m2 g−1 to 3.46 m2 g−1. The cristobalite grains of the frustules heat-treated at 1000℃ was smaller than 100 nm, while the grain size increased to ∼500 nm at 1200℃. The increased compressive stresses of the resin at the specific heat treatment temperature (1000℃) were ascribed to nano size crystalline cristobalite grains. The relatively lower compressive stresses of the epoxy resin filled with frustules heat-treated above 1000℃ were attributed to the micro-cracking of the frustules that might be resulted from higher density of the cristobalite than that of the opal and accompanying reduction of the surface area and the surface pore sizes that might impair the resin-frustule interlocking and intrusion.Article Citation - WoS: 12Citation - Scopus: 15Morphological and Molecular Identification of Pennate Diatoms Isolated From Urla, Izmir, Coast of the Aegean Sea(TUBITAK, 2013) Kesici, Kutsal; Tüney, İnci; Sukatar, Atakan; Zeren, Doğuş; Güden, MustafaDiatoms represent an important class of aquatic phototrophs. They are not only one of the major contributors to global carbon fixation, but also play a key role in the biogeochemical cycling of silica. Molecular identification methods based on conserved DNA sequences, such as ITS (Internal Transcribed Spacer) have revolutionized our knowledge and understanding of conventional taxonomy. In this study, we aimed to compare the conventional identification methods with molecular identification methods. To do so, we isolated four diatom samples from Coast of Urla and characterized them using light microscopy (LM) and scanning electron microscopy (SEM) according to morphological features. Then, we amplified ITS regions using conventional polymerase chain reaction (PCR), sequenced the PCR products and analyzed the sequences using bioinformatic tools. Bioinformatic analysis indicated that the isolated species had high sequence similarity to Pseudo-nitzschia sp., Achnanthes sp., Amphora sp. and Cylindrotheca sp. We believe that molecular identification methods enable rapid and more reliable identification of diatom species and are crucial for monitoring harmful algal blooms.