Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
4 results
Search Results
Article Citation - WoS: 18Citation - Scopus: 19The Impact Response of a Nomex® Honeycomb Core/E-glass Composite Sandwich Structure To Increasing Velocities: Experimental and Numerical Analysis(Elsevier, 2023) Çelik, Muhammet; Güden, Mustafa; Sarıkaya, Mustafa; Taşdemirci, Alper; Genç, Cem; Ersoy, Kurtuluş; Serin, ÖzgürThe impact response of an E-glass fiber reinforced epoxy/Nomex® honeycomb core sandwich was investigated both experimentally and numerically at increasing velocities through concentrated quasi-static indentation force (CQIF), low velocity impact (LVI) and high velocity impact (HVI) tests. The composite face sheets and core were modelled using MAT_162 and MAT_026 homogenized material model in LS-DYNA, respectively. The experimental and numerical LVI test forces corresponding to core crushing and face sheet penetration were shown to be higher than those of the CQIF tests and increased as the impactor velocity increased. The increase of the impact forces at increasing velocities was largely ascribed to the inertia and the strain rate sensitive fracture strength of the composite sheets. The core shearing was detected in the CQIF and LVI tests both experimentally and numerically. It was also detected in the HVI tests at the velocities less than 20 m s?1. The deformation in the HVI tests at and above ? 29.4 m s?1 was highly localized in the impact area with no core shearing and a large delamination damage area at the front face sheet. The force enhancement due to the micro-inertia of the core deformation was shown to be not significant at the studied velocities. © 2023 Elsevier LtdArticle Citation - WoS: 3Citation - Scopus: 3Enhancement of Filament Wound Glass Fiber/Epoxy-based Cylindrical Composites by Toughening With Single-Walled Carbon Nanotubes(SAGE Publications, 2022) Ay Solak, Zeynep; Kartav, Osman; Tanoğlu, MetinIn this study, the effect of incorporating nano-sized fillers (noncovalently functionalized with ethoxylated alcohol chemical-vapor-deposition-grown SWCNTs) within an epoxy resin on the performance of filament wound glass fiber (GF)-based cylindrical composites (GFCCs) was investigated. For this purpose, SWCNTs were dispersed with the concentration of 0.05 and 0.1 weight percent (wt.%) within an epoxy resin using mechanical stirring and calendaring (3-roll-milling) techniques. The rheological behavior of the SWCNT incorporated epoxy mixture was characterized to determine the suitability of blends for the filament winding process. It was revealed that the viscosity value of the resin was not significantly affected by the addition of SWCNTs in given concentrations. Moreover, contact angle measurements were also performed on the SWCNT/epoxy blends dropped on the GF for the evaluation of the wettability behavior of the GF in the presence of the SWCNTs in relevant concentrations. Eventually, it was observed that the wettability behavior of GF was not reasonably affected by the presence of the SWCNTs. The double cantilever beam (DCB), flexural, and short beam shear (SBS) tests were performed on the reference and SWCNT-modified GFCC specimens to evaluate the effects of the SWCNT presence on the interlaminar fracture toughness and out-of-plane properties of GFCCs. The fractured surfaces after the DCB and SBS tests were analyzed under the scanning electron microscopy to reveal the toughening mechanisms and the filler morphologies. Consequently, although SWCNT incorporation was on the outermost layer of GFCCs, it was found that the interlaminar shear strength (ILSS) values and Mode I interlaminar fracture toughness values of the curved composite samples were improved up to 22 and 216%, respectively, due to the presence of the SWCNTs.Article Citation - WoS: 7Citation - Scopus: 9Effects of Hybrid Yarn Preparation Technique and Fiber Sizing on the Mechanical Properties of Continuous Glass Fiber-Reinforced Polypropylene Composites(SAGE Publications, 2016) Merter, N. Emrah; Başer, Gülnur; Tanoğlu, MetinIn this study, hybrid yarns were developed by commingling the continuous polypropylene and glass fibers using air jet and direct twist preparation techniques. The non-crimp fabrics were obtained with +/- 45 degrees fiber orientation from these hybrid yarns. The fabrics were prepared with fiber sizings that are compatible and incompatible with polypropylene matrix to investigate the effect of interfacial adhesion on the properties of the thermoplastic composites. Composite panels were produced from the developed fabrics by hot press compression method and microstructural and mechanical properties of the composites were investigated. It was found that type of the hybrid yarn preparation technique and glass fiber sizing applied on the glass fibers have some important role on the properties of the composites. Composites made of fabrics produced by air jet hybrid yarn preparation technique exhibited better results than those produced by direct twist covering (single or double) hybrid yarn preparation techniques. The highest flexural properties (99.1MPa flexural strength and 9.55 GPa flexural modulus) were obtained from the composites manufactured from fabric containing compatible sizing, due to better adhesion at the interface of glass fibers and polypropylene matrix. The composite fabricated from fabric with polypropylene compatible sizing also exhibited the highest peel resistance (interlaminar peel strength value of 5.87N/mm). On the other hand, it was found that hybrid yarn preparation technique and type of the glass fiber sizing have insignificant effect on the impact properties of the glass fiber/polypropylene composites.Article Citation - WoS: 16Citation - Scopus: 24Developing Polymer Composite-Based Leaf Spring Systems for Automotive Industry(Walter de Gruyter GmbH, 2018) Öztoprak, Nahit; Güneş, Mehmet Deniz; Tanoğlu, Metin; Aktaş, Engin; Eğilmez, Oğuz Özgür; Şenocak, Çiler; Kulaç, GedizComposite-based mono-leaf spring systems were designed and manufactured to replace existing mono-leaf metal leaf spring in a light commercial vehicle. In this study, experimentally obtained mechanical properties of different fiber-reinforced polymer materials are presented first, followed by the description of the finite element analytical model created in Abaqus 6.12-1 (Dassault Systemes Simulia Corp., RI, US) using the obtained properties. The results from the finite element analysis are presented next and compared with actual size experimental tests conducted on manufactured prototypes. The results demonstrated that the reinforcement type and orientation dramatically influenced the spring rate. The prototypes showed significant weight reduction of about 80% with improved mechanical properties. The hybrid composite systems can be utilized for composite-based leaf springs with considerable mechanical performance.