Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
4 results
Search Results
Article Citation - WoS: 25Citation - Scopus: 25Characterization Investigations During Mechanical Alloying and Sintering of W-20 Vol% Sic Composites(Elsevier Ltd., 2010) Coşkun, Selim; Öveçoğlu, M. Lütfi; Özkal, Burak; Tanoğlu, MetinThe effect of mechanical alloying and the sintering regime on the microstructural and the physical properties of W-SiC composites were investigated. Powder mixtures of W-20 vol.% SiC were mechanically alloyed (MA'd) using a Spex mill for 3 h, 6 h and 24 h. MA'd powders were characterized by Laser Diffraction Particle Size Analyzer, SEM and XRD investigations. MA'd W-20 vol.% SiC powder composites were sintered under inert Ar and reducing H2 gas conditions at 1680 °C and 1770 °C for 1 h. The microstructural and mechanical characterizations of the sintered samples were carried out by scanning electron microscope (SEM) and X-ray diffraction (XRD) and Vickers Hardness analyses. The addition of SiC remarkably increases the hardness of the composites. Hardness is also increased with decreasing grain size and increasing amount of MA. © 2009 Elsevier B.V. All rights reserved.Article Citation - WoS: 17Citation - Scopus: 20Numerical and Experimental Studies of Damage Generation in a Polymer Composite Material at High Strain Rates(Elsevier Ltd., 2006) Taşdemirci, Alper; Hall, Ian W.Samples of S2-glass/epoxy composites have been subjected to microstructural investigation after testing in compression at quasi-static and high strain rates using the split Hopkinson pressure bar. A numerical model was developed that accurately describes the high strain rate mechanical response of the samples. Moreover, in contrast with earlier phenomenological or constitutive models, the model can also predict a variety of failure modes such as delamination, matrix cracking or fiber crushing. High-speed photography was used to check the model results. Interrupted tests, followed by metallographic examination, have revealed that the sequence of damage events differs between quasi-static and high strain rate regimes. The effect of sample size on measured mechanical properties is noted and is confirmed via numerical modeling.Article Citation - WoS: 32Citation - Scopus: 37Modeling Quasi-Static and High Strain Rate Deformation and Failure Behavior of a (±45) Symmetric E-glass/Polyester Composite Under Compressive Loading(Elsevier Ltd., 2013) Kara, Ali; Taşdemirci, Alper; Güden, MustafaQuasi-static (1 × 10−3–1 × 10−2 s−1) and high strain rate (∼1000 s−1) compressive mechanical response and fracture/failure of a (±45) symmetric E-glass/polyester composite along three perpendicular directions were determined experimentally and numerically. A numerical model in LS-DYNA 971 using material model MAT_162 was developed to investigate the compression deformation and fracture of the composite at quasi-static and high strain rates. The compressive stress–strain behaviors of the composite along three directions were found strain rate sensitive. The modulus and maximum stress of the composite increased with increasing strain rate, while the strain rate sensitivity in in-plane direction was higher than that in through-thickness direction. The damage progression determined by high speed camera in the specimens well agreed with that of numerical model. The numerical model successfully predicted the damage initiation and progression as well as the failure modes of the composite.Article Citation - WoS: 10High Strain Rate Behavior of a Sic Particulate Reinforced Al2o3 Ceramic Matrix Composite(Elsevier Ltd., 1998) Hall, Ian W.; Güden, MustafaThe high strain rate deformation behavior of composite materials is important for several reasons. First, knowledge of the mechanical properties of composites at high strain rates is needed for designing with these materials in applications where sudden changes in loading rates are likely to occur. Second, knowledge of both the dynamic and quasi-static mechanical responses can be used to establish the constitutive equations which are necessary to increase the confidence limits of these materials, particularly if they are to be used in critical structural applications. Moreover, dynamic studies and the knowledge gained form them are essential for the further development of new material systems for impact applications. In this study, the high strain rate compressive deformation behavior of a ceramic matrix composite (CMC) consisting of SiC particles and an Al{sub 2}O{sub 3} matrix was studied and compared with its quasi-static behavior. Microscopic observations were conducted to investigate the deformation and fracture mechanism of the composite.