Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
4 results
Search Results
Article Citation - WoS: 25Citation - Scopus: 26Lowering the Sintering Temperature of Solid Oxide Fuel Cell Electrolytes by Infiltration(Elsevier Ltd., 2019) Sındıraç, Can; Çakırlar, Seda; Büyükaksoy, Aligül; Akkurt, SedatA dense electrolyte with a relative density of over 95% is vital to prevent gas leakage and thus the achievement of high open circuit voltage in solid oxide fuel cells (SOFCs). The densification process of ceria based electrolyte requires high temperatures heat treatment (i.e. 1400-1500 degrees C). Thus, the minimum co-sintering temperatures of the anode-electrode bilayers are fixed at these values, resulting in coarse anode microstructures and consequently poor performance. The main purpose of this study is to densify gadolinia doped ceria (GDC), a common SOFC electrolyte, at temperatures lower than 1400 degrees C. By this aim, an approach involving the infiltration of polymeric precursors into porous electrolyte scaffolds, a method commonly used for composite SOFC electrodes, is proposed. By infiltrating polymeric precursors of GDC into porous GDC scaffolds, a reduction in the sintering temperature by at least 200 degrees C is achieved with no additives that might affect the electrical properties. Energy dispersive x-ray spectroscopy line scan analyses performed on porous GDC scaffolds infiltrated by a marker solution (polymeric FeOx precursor in this case) reveals a homogeneous infiltrated phase distribution, demonstrating the effectiveness of polymeric precursors.Article Citation - WoS: 11Citation - Scopus: 12Electrical Properties of Gadolinia Doped Ceria Electrolytes Fabricated by Infiltration Aided Sintering(Elsevier Ltd., 2019) Sındıraç, Can; Büyükaksoy, Aligül; Akkurt, SedatCommon solid oxide fuel cell (SOFC) electrolyte materials (e.g., gadolinia doped ceria - GDC) demand temperatures exceeding 1400 degrees C for densification by conventional solid state sintering. It is very desirable to reduce the densification of the SOFC electroltytes to i) avoid microstructural coarsening of the composite anode layers, which are co-sintered with the electolyte layer in the anode supported SOFC fabrication scheme and ii) reduce energy consumption during SOFC manufacturing. We have recently demostrated a novel infiltration-aided sintering route to densify GDC ceramics at 1200 degrees C. In the present work, we present the electrical properties of GDC ceramics fabricated thusly. Comparison of high density (>= 95%) samples fabricated by conventional or infiltration-aided sintering reveal that at 700 degrees C, similar total electrical conductivities are obtained, while at 300 degrees C, specific grain boundary resistivity is smaller in the latter. Bulk (grain) conductivity is higher in porous GDC ceramics (relative density <= 90%) fabricated by infiltration-aided sintering than the conventionally sintered ones with similar porosities. Finally, open circuit voltage of 0.84 V at 700 degrees C, obtained under dilute hydrogen and stagnant air conditions suggests that GDC ceramics densified by infiltration-aided sintering are suitable for use as SOFC electrolytes.Article Citation - WoS: 25Citation - Scopus: 25Characterization Investigations During Mechanical Alloying and Sintering of W-20 Vol% Sic Composites(Elsevier Ltd., 2010) Coşkun, Selim; Öveçoğlu, M. Lütfi; Özkal, Burak; Tanoğlu, MetinThe effect of mechanical alloying and the sintering regime on the microstructural and the physical properties of W-SiC composites were investigated. Powder mixtures of W-20 vol.% SiC were mechanically alloyed (MA'd) using a Spex mill for 3 h, 6 h and 24 h. MA'd powders were characterized by Laser Diffraction Particle Size Analyzer, SEM and XRD investigations. MA'd W-20 vol.% SiC powder composites were sintered under inert Ar and reducing H2 gas conditions at 1680 °C and 1770 °C for 1 h. The microstructural and mechanical characterizations of the sintered samples were carried out by scanning electron microscope (SEM) and X-ray diffraction (XRD) and Vickers Hardness analyses. The addition of SiC remarkably increases the hardness of the composites. Hardness is also increased with decreasing grain size and increasing amount of MA. © 2009 Elsevier B.V. All rights reserved.Article Citation - WoS: 3Citation - Scopus: 3Thermostable Tensoresistors of Co Doped Gasb-Fega1.3 Eutectic Composites(Elsevier Ltd., 2008) Rahimov, R. N.; Khalilova, A. A.; Arasly, D. H.; Aliyev, M. I.; Tanoğlu, Metin; Özyüzer, LütfiThe microstructure and tensoresistive properties of GaSb-FeGa1.3 eutectic composites doped with 0.1% Co have been investigated. It was found that the Co impurity atoms mainly accumulate in the metallic inclusions. The length of the inclusions in GaSb-FeGa1.3〈Co〉 was measured to be about half of those in undoped GaSb-FeGa1.3 eutectics. The tensometric characteristics of gauges based on GaSb-FeGa1.3〈Co〉 have been found to be more thermostable than undoped samples. © 2008 Elsevier B.V. All rights reserved.