Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
8 results
Search Results
Article Citation - WoS: 2Citation - Scopus: 3Design and Manufacturing of a Hip Joint Motion Simulator With a Novel Modular Design Approach(Springer, 2023) Torabnia, Shams; Mihçin, Şenay; Lazoğlu, İsmailThe study is aimed to develop a hip joint wear simulator using a modular design approach to help experimentally monitor and control critical wear parameters to validate in-silico wear models. The proper control and application of wear parameters such as the range of motion, and the applied force values while estimating the lost material due to wear are essential for thorough analysis of wear phenomena for artificial joints. The simulator's dynamics were first modeled, then dynamic loading data was used to calculate the forces, which were further used for topology optimization to reduce the forces acting on each joint. The reduction of the link weights, connected to the actuators, intends to improve the quality of motion transferred to the femoral head. The modular design approach enables topology-optimized geometry, associated gravitational and dynamic forces, resulting in a cost-effective, energy-efficient product. Moreover, this design allows integration of the subject specific data by allowing different boundary conditions following the requirements of industry 5.0. Overall, the in-vitro motion stimulations of the hip-joint prosthesis and the modular design approach used in the study might help improve the accuracy and the effectiveness of wear simulations, which could lead into the development of better and longer-lasting joint prostheses for all. The subject-specific and society-based daily life data implemented as boundary conditions enable inclusion of the personalized effects. Next, with the results of the simulator, CEN Workshop Agreement (CWA) application is intended to cover the personalized effects for previously excluded populations, providing solution to inclusive design for all.Article Citation - WoS: 15Citation - Scopus: 15The Effect of Strain Rate on the Compression Behavior of Additively Manufactured Short Carbon Fiber-Reinforced Polyamide Composites With Different Layer Heights, Infill Patterns, and Built Angles(Springer, 2023) Zeybek, Mehmet Kaan; Güden, Mustafa; Taşdemirci, AlperPrevious studies on the fused deposition modelling (FDM) processed short carbon fiber/Polyamide 6 (PA6) matrix composites and neat PA6 have mostly concentrated on the quasi-static mechanical properties. Present study focused on the strain rate-dependent deformation behavior of a short carbon fiber-reinforced PA6 (Onyx) and neat PA6, produced in different layer heights, infill patterns and built angles. As compared with PA6, Onyx showed a higher compression stress at all strain rates investigated. A layer height of 0.2 mm in PA6 specimens promoted a better bonding between [0/90°] infill layers; hence, a higher flow stress than 0.2 mm layer height specimens, while 0.2 mm layer height induced a higher porosity in Onyx specimens, leading to a lower flow stress. The porosities in Onyx [0/90°] infill specimens were due to the constraining effect of 0/90° fiber layers. Changing infill pattern from a [0/90°] to a concentric one decreased porosity at the same layer height and hence increased the compressive flow stress. The highest compressive strength was found in the specimens with the loading axis 90 and 0° to [0/90°] infill plane. The lowest strength was, however, determined in the specimens with the loading axis 30 and 60o to [0/90°] infill plane in quasi-static loading. However, the specimens with the loading axis of 60, 45, 30 and 0° exhibited a brittle behavior in high strain rate loading (1500 s−1). The specimens with the loading axis of 45° had the lowest fracture stress and strain in the high strain rate loading. This signified the importance of loading angle at high strain rates. Finally, the rate sensitivities of PA6 and Onyx specimens were shown to be similar, showing a matrix dominated deformation. However, the strain rate jump tests indicated a slightly higher rate sensitivity of Onyx specimens at quasi-static strain rates (10−3-10−1 s−1).Article Citation - WoS: 5Citation - Scopus: 5Loop Based Classification of Planar Scissor Linkages(Springer, 2022) Kiper, Gökhan; Korkmaz, Koray; Gür, Şebnem; Yar Uncu, Müjde; Maden, Feray; Akgün, Yenal; Karagöz, CevahirScissor linkages have been used for several applications since ancient Greeks and Romans. In addition to simple scissor linkages with straight rods, linkages with angulated elements have been introduced in the last decades. In the related literature, two methods have been used to design scissor linkages, one of which is based on scissor elements, and the other is based on assembling loops. This study presents a systematic classification of scissor linkages as assemblies of rhombus, kite, dart, parallelogram and anti-parallelogram loops using frieze patterns and long-short diagonal connections. After the loops are replicated along a curve as a pattern, the linkages are obtained by selection of proper common link sections for adjacent loops. The resulting linkages are analyzed for their motions and they are classified as realizing scaling deployable, angular deployable or transformable motion. Some of the linkages obtained are novel. Totally 10 scalable deployable, 1 angular deployable and 8 transformable scissor linkages are listed. Designers in architecture and engineering can use this list of linkages as a library of scissor linkage topologies.Article Design, Prototyping and Tests of a Rollable Ramp for Temporary Use(Springer, 2021) Doğan Kumtepe, Elvan; Kiper, GökhanPortable ramps, used generally by wheelchair users, offer temporary solution to increase accessibility and mobility. Preferably these ramps should be compact and lightweight for ease of handling and storage. Different types of portable ramps in the market that are used by wheelchair users are generally made of aluminum and require several improvements, especially in terms of lightweight and compactness. Based on wheelchair users’ inclinations a compact and lightweight rollable ramp is designed in this study. A parametric model of the links of the ramp are derived and the rolled geometry is optimized using convex hull and smallest enclosing circle algorithms. The side bars of the links are designed and manufactured from aluminum and the load-bearing panels are manufactured from sandwich composite structures with honeycomb core. Strength calculations are performed analytically and also with finite-element analysis. After the design is finalized, a prototype is manufactured. The designed ramp is 15.4% more compact and has 18.9% less weight compared to the best rival product available in the market. Load tests and functional tests are performed with voluntary wheelchair users. Several positive feedbacks are received from the participants about the ramp being practical, easy to use and store, lightweight, advantage of the anti-slip surface.Article Citation - WoS: 8Citation - Scopus: 8Comparing Compression Deformation and Rate Sensitivity of Additively Manufactured and Extruded-Annealed 316l Alloys(Springer, 2021) Enser, Samed; Yavaş, Hakan; Arslan Hamat, Burcu; Aydın, Hüseyin; Kafadar, Gülten; Tanrıkulu, A. Alptuğ; Zeytin Kazdal, Havva; Öztürk, Fahrettin; Güden, MustafaThe deformation behavior of a selective-laser-melt-processed 316-L alloy (SLM-316L) under compression was determined together with a commercial annealed-extruded 316L alloy bar (C-316L) for comparison. Strain rate jump tests and hardness tests on the untested and compression tested samples were also performed. Extensive microscopic observations on the deformed and undeformed samples showed a twinning-dominated deformation in SLM-316L, similar to twinning-induced-plasticity steels, while a martensitic transformation-dominated deformation in C-316L alloy, similar to transformation-induced-plasticity steels. Within the studied quasi-static strain rate regime, the measured higher strain rate sensitivity of SLM-316L was ascribed to the lower distances between the nano-twins, in the level of 100 nm, than the distances between martensite plates, in the level of 1000 nm. A higher hardness increase in the martensite transformation region as compared with the twinned region proved the higher work hardening of C-316L. The hardness tests in the micron and sub-micron levels further confirmed the previously determined relatively low resistances of the dislocation cell walls (sub-grain) to the dislocation motion in SLM-316L alloy.Article Citation - WoS: 3Citation - Scopus: 5Single- and Multiobjective Optimizations of Dimensionally Stable Composites Using Genetic Algorithms(Springer, 2021) Aydın, Levent; Artem, Hatice Seçil; Deveci, Hamza ArdaThe present study aims to design stacking sequences of dimensionally stable symmetric balanced laminated carbon/epoxy composites, with different numbers of layers, with a low coefficient of thermal expansion and high elastic moduli. To avoid excessive interlaminar stresses in the composites, the contiguity constraint for plies is also taken into consideration. In the design process, both single- and multiobjective optimization approaches, including genetic algorithms, are utilized. Results showed that stacking sequences ensuring lower thermal expansion coefficients and higher elastic moduli than those of traditional laminate designs can be obtained.Article Citation - WoS: 8Citation - Scopus: 8Pore Connectivity Effects on the Internal Surface Electric Charge of Mesoporous Silica(Springer, 2019) Şen, Tümcan; Barışık, MuratNano-scale confinements within mesoporous systems develop overlapping electric double layers (EDL) such that the existing theoretical models cannot predict the electric potential distributions and resulting surface charges. In addition, ionic conditions undergo local variation through connections between the pore voids and pore throats. For the first time in literature, we studied the charging behavior of mesoporous silica in terms of the pore to throat size ratio (R-pt) to characterize the pore connectivity effects, in addition to porosity (epsilon) and pore size (H). Both local and average surface charge densities inside mesoporous silica were examined by varying these parameters systematically. Results showed that the magnitude of surface charge density decreased with increasing EDL overlap and decreasing connectivity effects. We formulized this behavior and developed an extended model to predict mesoporous silica's internal charge as a function of porosity, pore size, and pore to throat size ratio.Article Citation - WoS: 15Citation - Scopus: 16Fabrication of Lscf and Lscf-Gdc Nanocomposite Thin Films Using Polymeric Precursors(Springer, 2020) Sındıraç, Can; Ahsen, Ali; Öztürk, Osman; Akkurt, Sedat; Birss, Viola, I; Büyükaksoy, AligülLa1-xSrxCoyFe1-yO3 (LSCF) and LSCF-gadolinia-doped ceria (LSCF-GDC) composites are used as solid oxide fuel cell (SOFC) cathodes. In the present study, to maximize the LSCF/gas and LSCF/GDC interfacial area and thus enhance the performance, we fabricated both single-phase LSCF and composite LSCF-GDC thin-film electrodes using a facile and cost-effective polymeric precursor technique. This method involves molecular level mixing of cations in solution form and results in average particle sizes of ca. 72 nm and 60 nm upon annealing at 700 degrees C, respectively. For LSCF, electrochemical impedance spectroscopy measurements indicate very low electrode polarization resistances of ca. 0.6 omega cm(2) per electrode at 600 degrees C. However, the addition of GDC results in poorer electrochemical activity but better microstructural and electrochemical stability, all at 600 degrees C. Surface analysis revealed that Fe surface segregation occurs in the single-phase LSCF, while predominantly Co segregation is observed at the LSCF-GDC composite electrode surface.