Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
6 results
Search Results
Article Citation - WoS: 8Citation - Scopus: 9Experimental Investigation of Air Cooling With/Out Tab Cooling in Cell and Module Levels for Thermal Uniformity in Battery Packs(ASME, 2023) Göçmen, Sinan; Çetkin, ErdalCatastrophic effects of global warming and environmental pollution are becoming more evident each day, and reduction in fossil fuel consumption is an urgent need. Thus, electric vehicles powered by sustainable energy sources are becoming a major interest. However, there are some challenges such as safety, limited range, long charging times, and battery life which are inhibitory to the adaptation of them. One of the biggest reasons for these challenges is the relationship between battery degradation and temperature which can be eliminated if batteries can be kept at the optimum temperature range. Here, the effects of three distinct (natural convection, forced convection, and tab cooling) methodology were experimentally compared at both the cell and module levels (six serial 7.5 Ah Kokam pouch cells, 1P6S) for thermal management of lithium-ion cells. The experiments were conducted at a discharge rate of 3C with ambient temperatures of 24 ◦C and 29 ◦C. The cell-level test results show that the tab cooling yields 32.5% better thermal uniformity in comparison to the other techniques. Furthermore, tab cooling yields better temperature uniformity with and without air convection as the hot spots occurring near the tabs is eliminated. For the module level, the forced air convection method stands out as the best option with a 4.3% temperature deviation between cells and maximum cell temperature of 39 ◦C. Overall, the results show that a hybrid approach with tab cooling would be beneficial in terms of temperature homogeneity especially in high capacity electric vehicle battery cells.Article Citation - WoS: 12Citation - Scopus: 13A General Expression for the Stagnant Thermal Conductivity of Stochastic and Periodic Structures(The American Society of Mechanical Engineers(ASME), 2018) Bai, X.; Çelik, Hasan; Mobedi, Moghtada; Nakayama, AkiraA general expression has been obtained to estimate thermal conductivities of both stochastic and periodic structures with high-solid thermal conductivity. An air layer partially occupied by slanted circular rods of high-thermal conductivity was considered to derive the general expression. The thermal conductivity based on this general expression was compared against that obtained from detailed three-dimensional numerical calculations. A good agreement between two sets of results substantiates the validity of the general expression for evaluating the stagnant thermal conductivity of the periodic structures. Subsequently, this expression was averaged over a hemispherical solid angle to estimate the stagnant thermal conductivity for stochastic structures such as a metal foam. The resulting expression was found identical to the one obtained by Hsu et al., Krishnan et al., and Yang and Nakayama. Thus, the general expression can be used for both stochastic and periodic structures.Article Citation - WoS: 31Citation - Scopus: 33Modification of Carbon Fibre/Epoxy Composites by Polyvinyl Alcohol (pva) Based Electrospun Nanofibres(Adcotec Ltd., 2016) Beylergil, Bertan; Tanoğlu, Metin; Aktaş, EnginIn this study, the effects of modifying interlaminar region of unidirectional carbon fibre/epoxy composites by the incorporation of electrospun polyvinyl alcohol (PVA) nanofibres were investigated. PVA nanofibres were directly deposited onto the carbon fabrics by electrospinning method to improve mechanical performance of those composites. The features of the electrospun nanofibres were characterized by microscopy techniques. The unidirectional carbon fibre/epoxy composite laminates with/without PVA nanofibre interlayers were manufactured by vacuum-infusion technique in a [0]4 configuration. Tensile, three-point bending, compression, Charpy-impact and Mode-I fracture toughness tests (Double Cantilever Beam (DCB)) were carried out in accordance with ASTM standards to evaluate mechanical performance of the composites. Scanning electron microscopy (SEM) observations were made on the specimens to evaluate microstructural features. It was observed that the carbon fabrics were successfully coated with a thin layer of PVA nanofibres by electrospinning technique. The results showed that P VA nanofibres improve the mechanical properties of unidirectional carbon/epoxy composite laminates when subjected to in-plane loading. On the other hand, PVA nanofibres slightly reduced the mode-I fracture toughness values although they led to more stable crack propagation.Article Citation - WoS: 10Citation - Scopus: 10Constructal Microdevice Manifold Design With Uniform Flow Rate Distribution by Consideration of the Tree-Branching Rule of Leonardo Da Vinci and Hess-Murray Rule(The American Society of Mechanical Engineers(ASME), 2017) Çetkin, ErdalIn this paper, we show how the design of a microdevice manifold should be tapered for uniform flow rate distribution. The designs based on the tree-branching rule of Leonardo da Vinci and the Hess-Murray rule were considered in addition to the constructal design. Both da Vinci and Hess-Murray designs are insensitive to the inlet velocity, and they provide better flow uniformity than the base (not tapered) design. However, the results of this paper uncover that not only pressure drop but also velocity distribution in the microdevice play an integral role in the flow uniformity. Therefore, an iterative approach was adopted with five degrees-of-freedom (inclined wall positions) and one constraint (constant distribution channel thickness) in order to uncover the constructal design which conforms the uniform flow rate distribution. In addition, the effect of slenderness of the microchannels (Svelteness) and inlet velocity on the flow rate distribution to the microchannels has been documented. This paper also uncovers that the design of a manifold should be designed with not only the consideration of pressure distribution but also dynamic pressure distribution especially for non-Svelte microdevices.Article Citation - WoS: 13Citation - Scopus: 15Constructal Vascular Structures With High-Conductivity Inserts for Self-Cooling(The American Society of Mechanical Engineers(ASME), 2015) Çetkin, ErdalIn this paper, we show how a heat-generating domain can be cooled with embedded cooling channels and high-conductivity inserts. The volume of cooling channels and high-conductivity inserts is fixed, so is the volume of the heat-generating domain. The maximum temperature in the domain decreases with high-conductivity inserts even though the coolant volume decreases. The locations and the shapes of high-conductivity inserts corresponding to the smallest peak temperatures for different number of inserts are documented,Article Citation - WoS: 13Citation - Scopus: 19Effect of Pore To Throat Size Ratio on Interfacial Heat Transfer Coefficient of Porous Media(The American Society of Mechanical Engineers(ASME), 2015) Özgümüş, Türküler; Mobedi, MoghtadaIn this study, the effects of pore to throat size ratio on the interfacial heat transfer coefficient for a periodic porous media containing inline array of rectangular rods are investigated, numerically. The continuity, Navier-Stokes, and energy equations are solved for the representative elementary volume (REV) of the porous media to obtain the microscopic velocity and temperature distributions in the voids between the rods. Based on the obtained microscopic temperature distributions, the interfacial convective heat transfer coefficients and the corresponding Nusselt numbers are computed. The study is performed for pore to throat size ratios between 1.63 and 7.46, porosities from 0.7 to 0.9, and Reynolds numbers between 1 and 100. It is found that in addition to porosity and Reynolds number, the parameter of pore to throat size ratio plays an important role on the heat transfer in porous media. For the low values of pore to throat size ratios (i.e., β = 1.63), Nusselt number increases with porosity while for the high values of pore to throat size ratios (i.e., β = 7.46), the opposite behavior is observed. Based on the obtained numerical results, a correlation for the determination of Nusselt number in terms of porosity, pore to throat size ratio, Reynolds and Prandtl numbers is proposed.