Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
12 results
Search Results
Article Citation - WoS: 37Citation - Scopus: 41Processing and Characterization of Geopolymer and Sintered Geopolymer Foams of Waste Glass Powders(Elsevier, 2021) Polat, Dilan; Güden, MustafaGeopolymer foams of fine and coarse waste glass (WG) powders were prepared using an activation solution of NaOH (8 M) and Na2SiO3. The effects of WG powder particle size, solid/liquid ratio (S/L = 1, 1.5, and 2) and Al foaming agent content (2-20 wt%) on the expansion and temperature behavior of the slurries were determined in-situ using a laser sensor and a thermocouple, respectively. The geopolymer foams processed using a coarse WG powder slurry, S/L = 2, and 2 wt% Al, were further sintered at 600, 700, 725, and 750 degrees C. The compression strengths and thermal conductivities of the geopolymer and sintered geopolymer foams were also determined. The slurry expansions continued until about a maximum, and the temperatures of the slurries increased to a maximum, 85-88 degrees C. At the maximum temperature, the slurry evaporation and the resultant increase in the S/L ratio limited the slurry expansion. Increasing the Al content decreased the final density of the foams (238-555 kg m-3), while the coarse powder slurries resulted in lower densities than the fine powder slurries. Three crystal phases, muscovite, sodium aluminum silicate hydrate, and thermonitrite, were determined in the geopolymer foams. The muscovite formation was noted to be favored at high S/L ratios. During sintering, the partial melting of glass particles started after about 700 degrees C, while sintering above this temperature decreased the final density of the foams. The reduced density above 700 degrees C was ascribed to the release of CO2 due to the decomposition of thermonitrite. Both the compressive strength and thermal conductivity of the geopolymer and sintered geopolymer foams increased with increasing foam density. The highest increase in the compressive strength and reduction in the density were seen in the geopolymer foams sintered at 750 degrees C.Article Citation - WoS: 6Citation - Scopus: 6The Expansion Behavior of Slurries Containing Recycled Glass Powder Carboxymethyl Cellulose, Lime and Aluminum Powder(Elsevier, 2020) Zeren, Doğuş; Şentürk, Ufuk; Güden, MustafaThe rheology and foaming/expansion of the slurries of a waste/recycled glass powder with 50, 55 and 60 wt% of solid (glass powder) were experimentally investigated. The glass powder slurries were foamed using aluminum powder as foaming agent (0.75 wt%) and calcium hydroxide as activator (1 wt%). Sodium carboxymethyl cellulose (CMC) was added to the slurries as a binder with the amounts between 0 and 4 wt%. The expansions of the slurries were measured in-situ using a laser sensor and reported as percent volume expansion. The CMC-addition increased the viscosities of the slurries, particularly the fine size powder slurries. The slurries with the relatively low-viscosity exhibited lower initial expansion rates compared to the slurries with the relatively high-viscosity. The maximum expansions of the slurries increased from 300 to 350%, when the viscosity increased to 5 Pa s and reached a steady value around 400% between 5 and 50 Pa s. The expansions of the slurries could not be achieved above 50 Pa s since they became too thick to be foamed. The foam samples made from the slurries with 55 and 60 wt% of solid and sintered at 700 and 750 degrees C for 30 min had the average densities between 355 and 530 kg m(-3) and the average compressive strengths between 0.2 and 0.5 MPa. Increasing sintering time to 60 min at 750 degrees C increased the average compressive strength from 0.5 to 1.5 MPa for the foam samples made from the slurry with 60 wt% of solid. These proved that both sintering temperature and time were effective in increasing the compressive strengths of the foamed structures. The thermal conductivities of the sintered foam samples with the densities of 355 and 504 kg m(-3) were measured 0.042 and 0.057 W m(-1) K-1, respectively. (C) 2019 Elsevier Ltd. All rights reserved.Article Citation - WoS: 5Citation - Scopus: 6The Varying Densification Strain in a Multi-Layer Aluminum Corrugate Structure: Direct Impact Testing and Layer-Wise Numerical Modelling(Elsevier Ltd., 2017) Odacı, İsmet Kutlay; Güden, Mustafa; Kılıçaslan, Cenk; Taşdemirci, AlperAn aluminum (1050 H14) multi-layer corrugated structure composed of brazed 16 trapezoidal zig-zig fin layers was direct impact tested above the critical velocities for shock formation using a modified Split Hopkinson Pressure Bar. The experimentally measured stress-time histories of the cylindrical test samples in the direct impact tests were verified with the simulations implemented in the explicit finite element code of LS–DYNA. The quasi-static experimental and simulation deformation of the corrugated samples proceeded with the discrete, non-contiguous bands of crushed fin layers, while the dynamic crushing started from the proximal impact end and proceeded with a sequential and in-planar manner, showing shock type deformation characteristic. The experimental and numerical crushing stresses and the numerically determined densification strains of the fin layers increased with increasing impact velocity above the critical velocities. When the numerically determined densification strain at a specific velocity above the critical velocities was incorporated, the rigid-perfectly-plastic-locking idealized model resulted in peak stresses similar to the experimental and simulation mean crushing stresses. However, the model underestimated the experimental and simulation peak stresses below 200 m s−1. It was proposed, while the micro inertial effects were responsible for the increase of the crushing stresses at and below subcritical velocities, the shock deformation became dominant above the critical velocities.Conference Object Sic-vıskır/alüminyum Kompozit Köpüklerin Hazırlanması ve Mekanik Özelliklerinin Belirlenmesi(Pamukkale Üniversitesi, 2004) Saatçi, Levent; Güden, MustafaKöpükleştirici TiH2 içeren SiC-viskır/Al kompozit tabletler erime sıcaklığının üzerinde ısıtılarak köpükleşme davranışları belirlenmiştir. SiC-vıskır katkısının köpükleşme ve mekanik özelliklere (basma) etkisini belirlemek üzere aynı sıcak-pesleme ve köpükleşme parametleri kullanılarak saf alüminyum tabletler hazırlanmıştır. Köpükleşme sıcaklığı sabit tutulup 750oC olarak seçilmiştir. Tabletlerin doğrusal büyümeleri farklı sürelerde fırında köpükleşen numunelerin boyutları ölçülerek bulunmuştur. Köpükler hazırlandıktan sonra mekanik özellikleri belirlenmek üzere, sabit hızda basma testi uygulanmıştır. Sonuçlar, SiCv/Al ve Al tabletlerde köpükleşmenin benzer olduğunu fakat SiC-vıskır katkısının plato gerilmesini önemli derecede artırdığını göstermiştir.Article Citation - WoS: 71Citation - Scopus: 81The Impact Responses and the Finite Element Modeling of Layered Trapezoidal Corrugated Aluminum Core and Aluminum Sheet Interlayer Sandwich Structures(Elsevier Ltd., 2013) Kılıçaslan, Cenk; Güden, Mustafa; Odacı, İsmet Kutlay; Taşdemirci, AlperThe impact responses of brazed and adhesively bonded layered 1050 H14 trapezoidal corrugated aluminum core and aluminum sheet interlayer sandwich panels with 3003 and 1050 H14 aluminum alloy face sheets were investigated in a drop weight tower using spherical, flat and conical end striker tips. The full geometrical models of the tests were implemented using the LS-DYNA. The panels tested with spherical and flat striker tips were not penetrated and experienced slightly higher deformation forces and energy absorptions in 0°/90° corrugated layer orientation than in 0°/0° orientation. However, the panels impacted using a conical striker tip were penetrated/perforated and showed comparably smaller deformation forces and energy absorptions, especially in 0°/90° layer orientation. The simulation and experimental force values were shown to reasonably agree with each other at the large extent of deformation and revealed the progressive fin folding of corrugated core layers and bending of interlayer sheets as the main deformation mechanisms. The experimentally and numerically determined impact velocity sensitivity of the tested panels was attributed to the micro inertial effects which increased the critical buckling loads of fin layers at increasingly high loading rates.Article Citation - WoS: 27Citation - Scopus: 30Single- and Double-Layer Aluminum Corrugated Core Sandwiches Under Quasi-Static and Dynamic Loadings(SAGE Publications Inc., 2016) Kılıçaslan, Cenk; Odacı, İsmet Kutlay; Güden, MustafaThe crushing of single- and double-layer zig-zag trapezoidal corrugated core sandwiches was investigated experimentally and numerically at quasi-static and dynamic rates. The buckling stress of sandwiches increased when the rate increased from quasi-static to dynamic. The increased buckling stresses were ascribed to the micro-inertial effects, which altered the buckling mode of the core from three plastic hinges to higher number of plastic hinge formations. The initial buckling stress was numerically shown to be imperfection sensitive when the imperfection size was comparable with the buckling length. The numerical buckling stresses of zig-zag and straight corrugated cores were similar, while higher inertial effects were found in triangular corrugated core.Article Citation - WoS: 47Citation - Scopus: 62Transverse and Longitudinal Crushing of Aluminum-Foam Filled Tubes(Elsevier Ltd., 2002) Hall, Ian W.; Güden, Mustafa; Claar, Terry DennisAl-foam filled and empty tubes of aluminum, brass and titanium were compression tested laterally. The specific energy absorption in filled tubes increased greatly in terms of percentages, and was greatest in aluminum tubes. In transversely tested tubes the foam deformed laterally showing a capability of spreading the deformation.Article Citation - WoS: 67Citation - Scopus: 82Microhardness and Fracture Toughness of Dental Materials by Indentation Method(John Wiley and Sons Inc., 2005) Şakar-Deliormanlı, Aylin; Şakar Deliormanlı, Aylin Müyesser; Güden, Mustafa; Güden, MustafaThe main objective of this study was to measure the fracture toughness of the human teeth enamel using the microindentation technique and to compare the results calculated from the equations developed for Palmqvist and radial-median cracks. Vickers microhardness measurements of dental ceramic (alumina) and human teeth were performed using indentation fracture method. The fracture toughness of enamel was calculated using different equations reported in the literature. Vickers microhardness of the sintered alumina specimen (98.8% theoretical density) was measured to be 14.92 GPa under 9.8N indentation load. Three equations based on the radial-median cracks were found to be applicable for the fracture toughness determination of the enamel. Results show that indentation fracture method is adequate to measure microhardness and fracture toughness of dental materials. However the calculation of fracture toughness depended on the nature of the cracks and also on the location of the indentation. Therefore, it is necessary to identify the crack profile and to select the appropriate equation for accurate fracture toughness values.Article Citation - WoS: 29Citation - Scopus: 29Effect of Adhesive on the Strengthening of Aluminum Foam-Filled Circular Tubes(Springer Verlag, 2004) Toksoy, Ahmet Kaan; Tanoğlu, Metin; Güden, Mustafa; Hall, Ian W.Studies of the crushing behavior of closed-cell, aluminum foam-filled aluminum and steel tubes have shown an interaction effect between tubewall and foam filler [1, 2, 3]. The crushing loads of foam-filled tubes are, therefore, found to be higher than the sum of the crushing loads of foam (alone) and tube (alone) mainly due to this effect. Santosa et al. [1], based on FEM results, proposed the following equation for the average crushing load of foam-filled square tubes of length b,Article Citation - WoS: 194Citation - Scopus: 227Dynamics of Metal Foam Deformation During Taylor Cylinder–hopkinson Bar Impact Experiment(Elsevier Ltd., 2003) Lopatnikov, Sergey L.; Gama, Bazle A.; Haque, Jahirul; Krauthauser, Carl; Gillespie, John W.; Güden, Mustafa; Hall, Ian W.Analytical solutions for dynamic deformation of foam materials during the Taylor cylinder–Hopkinson bar impact experiment were obtained. It was shown that shock wave of foam collapse appears during the fast impact. The results of this experiment can be used in estimating the average material properties of the foam under dynamic loading conditions. Results show that the un-deformed and change in length of foam specimens are in good agreement between theory and experiment, as well as numerical analysis.