Mechanical Engineering / Makina Mühendisliği

Permanent URI for this collectionhttps://hdl.handle.net/11147/4129

Browse

Filters

2017 - 20193

Settings

Author: search.filters.author.Çelik, HasanSubject: search.filters.subject.Porous media

Search Results

Now showing 1 - 3 of 3
  • Article
    Citation - WoS: 120
    Citation - Scopus: 136
    Numerical Study on Latent Thermal Energy Storage Systems With Aluminum Foam in Local Thermal Equilibrium
    (Elsevier, 2019) Buonomo, Bernardo; Çelik, Hasan; Ercole, Davide; Manca, Oronzio; Mobedi, Moghtada
    The paper analyzes the behavior of a Latent Heat Thermal Energy Storage system (LHTES) with a Phase Change Material (PCM), with and without aluminum foam. A numerical investigation in a two-dimensional domain is accomplished to investigate on the system thermal evolution. The enthalpy-porosity method is used to describe the PCM melting. The open-celled aluminum foam is described as a porous medium by means of the Darcy-Forchheimer law. A hollow cylinder represents the considered thermal energy storage and it consists of the enclosure between two concentric shell tubes. The external surface of the internal tube is at assigned temperature with a value greater than the melting PCM temperature, while the other surfaces are adiabatic. Local thermal equilibrium (LTE) is numerically adopted for modelling the heat transfer between the PCM and the solid matrix in aluminum foam. In the case with metal foam, simulations for different porosities are performed. A comparison in term of liquid fraction, average temperature of the system, temperature fields, stream function and a performance parameter are made between the clean case and porous assisted case for the different porosities. A scale analysis is developed for evaluating the time and the melting zone in different regimes (i.e. conduction, mixed conduction-convective and convective) during the melting processes of the PCM in porous media. Numerical simulation shows that aluminum foam increases overall heat transfer by a magnitude of two, with respect to the clean case.
  • Article
    Citation - WoS: 6
    Citation - Scopus: 6
    A Study on Numerical Determination of Permeability and Inetia Coefficient of Aluminum Foam Using X-Ray Microtomography Techniques: Focus on Inspection Methods for Reliability (permeability and Inertia Coefficient by Tomography)
    (Begell House, 2019) Mobedi, Moghtada; Nakayama, Akira; Özkol, Ünver; Çelik, Hasan
    The volume-averaged (i.e., macroscopic) transport properties such as permeability and inertia coefficient of two aluminum foams with 10 and 20 pores per inch (PPI) pore density are found using microtomography images. It is shown that a comparison between the numerical values and the experimental results may not be sufficient to prove the correctness of the obtained results. Hence, in addition to traditional validation methods such as grid independency and comparison with reported results in literature, further inspections such as (a) checking the development of flow, (b) inspection of Darcy and non-Darcy regions, (c) conservation of flow rate through the porous media, (d) sufficiency of number of voxels in the narrow throats, and (e) observation of transverse velocity gradients in pores for high and low Reynolds numbers can be performed to further validate the achieved results. These techniques have been discussed and explained in detail for the performed study. Moreover, the obtained permeability and inertia coefficient values are compared with 19 reported theoretical, numerical, and experimental studies. The maximum deviation between the present results and the reported studies for 10 PPI is below 25%, while for 20 PPI it is below 28%.
  • Article
    Citation - WoS: 15
    Citation - Scopus: 16
    A Pore Scale Analysis for Determination of Interfacial Convective Heat Transfer Coefficient for Thin Periodic Porousmedia Undermixed Convection
    (Emerald Group Publishing Ltd., 2017) Çelik, Hasan; Mobedi, Moghtada; Manca, Oronzio; Özkol, Ünver
    Purpose - The purpose of this study is to determine interfacial convective heat transfer coefficient numerically, for a porous media consisting of square blocks in inline arrangement under mixed convection heat transfer. Design/methodology/approach - The continuity, momentum and energy equations are solved in dimensionless form for a representative elementary volume of porous media, numerically. The velocity and temperature fields for different values of porosity, Ri and Re numbers are obtained. The study is performed for the range of Ri number from 0.01 to 10, Re number from 100 to 500 and porosity value from 0.51 to 0.96. Based on the obtained results, the value of the interfacial convective heat transfer coefficient is calculated by using volume average method. Findings - It was found that at low porosities (such as 0.51), the interfacial Nusselt number does not considerably change with Ri and Re numbers. However, for porous media with high Ri number and porosity (such as 10 and 0.51, respectively), secondary flows occur in the middle of the channel between rods improving heat transfer between solid and fluid, considerably. It is shown that the available correlations of interfacial heat transfer coefficient suggested for forced convection can be used for mixed convection for the porous media with low porosity (such as 0.51) or for the flow with low Ri number (such as 0.01). Originality/value - To the best of the authors' knowledge, there is no study on determination of interfacial convective heat transfer coefficient for mixed convection in porous media in literature. The present study might be the first study providing an accurate idea on the range of this important parameter, which will be useful particularly for researchers who study on mixed convection heat transfer in porous media, macroscopically.