Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
27 results
Search Results
Now showing 1 - 10 of 27
Conference Object Citation - WoS: 1Citation - Scopus: 1Numerical and Experimental Studies of High Strain Rate Mechanical Behavior of E-glass/Polyester Composite Laminates(The American Society of Mechanical Engineers(ASME), 2010) Tunusoğlu, Gözde; Taşdemirci, Alper; Güden, Mustafa; Hall, Ian W.Quasi-static ∼10-3 s-1) and high strain rate (∼850 s-1) compression behavior of an E-glass/polyester composite was determined in the through-thickness and in-plane directions. In both directions, modulus and failure strength increased with increasing strain rate. Higher strain rate sensitivity for both elastic modulus and failure strength was observed in the in-plane direction. A numerical model was developed to investigate the compressive deformation and fracture of an E-glass/polyester composite. Excellent agreement was demonstrated for the case of high strain rate loading. Also, the fracture geometries were successfully predicted with the numerical model.Conference Object High Strain Rate Reloading Compresson Testing of a Closed-Cell Alumnum Foam(The European Association for Experimental Mechanics, 2007) Taşdemirci, Alper; Güden, Mustafa; Hall, Ian W.Aluminum (Al) closed-cell foams are materials of increasing importance because they have good energy absorption capabilities combined with good thermal and acoustic properties. They can convert much of the impact energy into plastic energy and absorb more energy than bulk metals at relatively low stresses. When used as filling materials in tubes, they increase total energy absorption over the sum of the energy absorbed by foam alone and tube alone [1]. In designing with metallic foams as energy absorbing fillers, mechanical properties are needed for strain rates corresponding to those created by impact events. Quasi-static mechanical behavior of metallic foams has been fairly extensively studied, but data concerning high strain rate mechanical behavior of these materials are, however, rather sparse [2,3]. This study was initiated, therefore, to study and model the high strain rate mechanical behavior of an Al foam produced by foaming of powder compacts and to compare it with quasi-static behavior and, hence, determine any effect on energy absorbing capacity.Conference Object Axial Compression of Aluminum Closed-Cell Foam Filled and Empty Aluminum Tubes(Uludağ Üniversitesi, 2002) Toksoy, Ahmet Kaan; Güden, Mustafa; Hall, Ian W.Aluminum closed-cell foam filled aluminum tubes with a polyester bonding layer between foam core and tube wall have been compression tested in ord er to detemiine specific energy absorption for the crash box applications. Aluminum foam, empty and foam filled tubes without bonding layer were also tested for comparison purposes, Preliminary results have shown that interaction effect has been found in foam filled tubes with polyester layer. In order to identify deforiDation mechanisms involving with tube deforination, deformed empty and foam filled tubes crosssections were microscopically analyzed and operative defoimationmechanisms were determined.Conference Object Alüminyum Oksit Uzun Fiber Destekli Mg Matris Kompozitlerin Statik ve Yüksek Hız Basma Davranışı(Pamukkale Üniversitesi, 2004) Akil, Övünç; Güden, Mustafa; Çiftçioğlu, Muhsin; Hall, Ian W.; Taşdemirci, AlperBu çalışmada uzun alüminyum oksit (FP™) fiber destekli magnezyum matris kompozitlerin enine basma davranışının deformasyon hızına bağlı değişimi araştırılmıştır. Silindirik numuneler fiber doğrultusuna dik yönde değişik uzama oranlarında Split Hopkinson basınç çubuğu ve statik mekanik test cihazı kullanılarak test edilmiş uzama-gerilme ilişkileri incelenmiştir. Bunun yanında optik mikroskop ve SEM kullanılarak kırılma mekaniği belirlenmeye çalışılmıştır. Çalışma sonucunda malzemenin enine basma mukavemetinin deformasyon hızı ile arttığı tespit edilmiş olup mikro-yapı incelemesinde deformasyonun ikizlenme ve kayma ile gerçekleştiği belirlenmiştir.Article Citation - WoS: 12Citation - Scopus: 12The Effect of Strain Rate on the Compressive Deformation Behavior of a Sintered Ti6al4v Powder Compact(Elsevier Ltd., 2008) Taşdemirci, Alper; Hızal, Alpay; Altındiş, Mustafa; Hall, Ian W.; Güden, MustafaThe high strain rate (220–550 s−1) and quasi-static (0.0016 s−1) compression deformation behavior of a sintered Ti6Al4V powder compact was investigated. The compact was prepared using atomized spherical particles (100–200 μm) and contained 38 ± 1% porosity. The deformation sequences of the tested samples were further recorded by high speed camera and analyzed as a function of strain. The failure of the compact, which was found to be similar in the studied high strain rate and quasi-static strain rate testing regimes, occurs through particle decohesion along the surface of the two cones in a ductile (dimpled) mode consisting of void initiation and growth and by void coalescence in the interparticle bond region. The effect of strain rate was to increase the flow stress and compressive strength of the compact while the critical strain corresponding to the maximum stress was shown to be strain rate independent.Article Citation - WoS: 24Citation - Scopus: 26Split Hopkinson Pressure Bar Compression Testing of an Aluminum Alloy: Effect of Lubricant Type(Chapman & Hall, 2003) Hall, Ian W.; Güden, MustafaThe Split Hopkinson Pressure Bar (SHPB), or Kolsky Bar, is widely used for studying the dynamic mechanical properties of metals and other materials. A cylindrical specimen is sandwiched between the incident and transmitter bars, Fig. 1, and a constant amplitude elastic wave is generated by the striker bar. Strain gages mounted on the incident and transmitter bars allow the compressive stress-strain response of the specimen to be established using uniaxial elastic wave theory [1]. A more detailed overview of SHPB testing is found in [2]. Lubricant is usually applied to the interfaces because the presence of any frictional effect on the specimen surfaces forms a multiaxial stress-state and invalidates one of the most important assumptions of the SHPB analysis, namely, a uniaxial stress state. This paper quantifies the effect for an aluminum alloy.Article Citation - WoS: 54Citation - Scopus: 62Sic-Particulate Aluminum Composite Foams Produced by Powder Compacts: Foaming and Compression Behavior(Springer Verlag, 2003) Elbir, Semih; Yılmaz, Selahattin; Toksoy, Ahmet Kaan; Güden, Mustafa; Hall, Ian W.The foaming behavior of SiC-particulate (8.6% by volume) aluminum composite powder compacts contained Titanium Hydride blowing agent was investigated by heating above the melting temperature (750°C) in a pre-heated furnace. Aluminum powder compacts were also prepared and foamed using similar compaction and foaming parameters in order to determine the effect of SiC-particulate addition on foaming and compression behavior. The linear expansions of the compacts at various furnace holding times were ex situ determined. Optical and scanning electron microscopy techniques were used to characterize prepared and deformed foams microstructures. The SiC-particulate addition was found to increase the linear expansion and reduce the extent of the liquid metal drainage and cell coarsening of the aluminum compacts. The composite foam samples also showed higher compressive stresses, but a more brittle behavior as compared with aluminum foams.Article Citation - WoS: 21Citation - Scopus: 25Quasi-Static and Dynamic Crushing of Empty and Foam-Filled Tubes(Springer Verlag, 2001) Hall, Ian W.; Ebil, Özgenç; Güden, Mustafa; Yu, C.-J.Metallic foam-filled tubes and their empty counterparts have been tested at quasi-static and dynamic strain rates in order to determine their energy absorption capabilities. Data from the Split-Hopkinson Pressure Bar have been used to generate force vs. displacement curves that are somewhat analogous to pseudo-engineering stress-strain curves. Force balance calculations have also been made. These results indicate that, on an equal weight basis, foam-filled tubes offer greater energy absorption capability than empty tubes at quasi-static strain rates. However, the benefit of foam filling does not appear to be extended to strain rates of the order of 200–500 s−1. Force balance calculations are shown to have potential as a method for monitoring the crushing of metallic foams at high strain rate.Article Citation - WoS: 11Citation - Scopus: 14Quasi-Static and Dynamic Compression Behaviour of an Fptm Alumina-Reinforced Aluminium Metal Matrix Composite(Springer Verlag, 1998) Güden, Mustafa; Hall, Ian W.An aluminium metal matrix composite reinforced with continuous unidirectional α-alumina fibres has been compression tested at quasi-static and dynamic strain rates. In the transverse direction, the composite showed increasing flow stress (at 5% strain) and maximum stress within the studied strain rates, 10−3−3 × 103 s−1. In the longitudinal direction, the maximum stress of the composite increased similarly with increasing strain rates within the range 10−5−7 × 102 s−1. It is shown that, if brooming of the sample ends can be suppressed, the failure stress of the composite in longitudinal compression increases significantly. Metallographic observations reveal the typical modes of damage initiation in the composite.Article Citation - WoS: 47Citation - Scopus: 62Transverse and Longitudinal Crushing of Aluminum-Foam Filled Tubes(Elsevier Ltd., 2002) Hall, Ian W.; Güden, Mustafa; Claar, Terry DennisAl-foam filled and empty tubes of aluminum, brass and titanium were compression tested laterally. The specific energy absorption in filled tubes increased greatly in terms of percentages, and was greatest in aluminum tubes. In transversely tested tubes the foam deformed laterally showing a capability of spreading the deformation.
- «
- 1 (current)
- 2
- 3
- »