Mechanical Engineering / Makina Mühendisliği

Permanent URI for this collectionhttps://hdl.handle.net/11147/4129

Browse

Filters

2018 - 201922020 - 20212

Settings

Department: search.filters.department.İzmir Institute of Technology. Mechanical EngineeringSubject: search.filters.subject.Modelling

Search Results

Now showing 1 - 4 of 4
  • Article
    Citation - WoS: 54
    Citation - Scopus: 59
    Orientation Dependent Tensile Properties of a Selective-Laser 316l Stainless Steel
    (Elsevier, 2021) Güden, Mustafa; Yavaş, Hakan; Tanrıkulu, Ahmet Alptuğ; Taşdemirci, Alper; Akın, Barış; Enser, Samed; Karakuş, Ayberk; Arslan Hamat, Burcu
    The effect of specimen inclination angle with respect to building direction on the tensile properties of a selective laser melt 316L alloy was investigated. Tensile test specimens were fabricated with the angles between 0 degrees to 90 degrees at 15 degrees intervals using a rotation scanning. In addition, 316L alloy test specimens were generated in the ANSYS 2020R1 additive module and tensile tested in LS-DYNA in order to determine the effect of residual stresses on the tensile strengths. The microscopic analysis revealed a strong < 110 > fiber texture orientation along the building direction (the loading axis of 0 degrees inclined specimens) and a weak 111 texture or nearly random distribution of directions in the normal to the building direction (tensile loading axis of 90 degrees inclined specimens). The yield and tensile strength increased and ductility decreased with increasing inclination angle. The strength variation with the inclination angle was shown well-fitted with the Tsai-Hill failure criterion. Although, the used numerical models indicated an inclination-dependent residual stress, the difference in the residual stresses was much lower than the difference in the strengths between 0 degrees and 90 degrees inclined specimens. Predictions showed a lower twinning stress in 0 degrees inclined specimens due to < 110 > fiber texture orientation in the tensile axis. The fiber texture resulted in extensive twinning; hence, higher ductility and tension-compression asymmetry in 0 degrees inclined specimens. Based on these results, the variations in the strength and ductility of tested SLM-316L specimens with the inclination angle was ascribed to the variations in the angle between the fiber texture orientation and loading axis.
  • Article
    Citation - WoS: 3
    Citation - Scopus: 4
    Impact Loading and Modelling a Multilayer Aluminium Corrugated/Fin Core: the Effect of the Insertion of Imperfect Fin Layers
    (John Wiley and Sons Inc., 2019) Sarıkaya, Mustafa; Taşdemirci, Alper; Güden, Mustafa
    The quasi-static compression (0.0048 m/s) and Taylor-like impact (135, 150, and 200 m/s) loading of a multilayer 1050 H14 aluminium corrugated core were investigated both experimentally and numerically in LS-DYNA using the perfect and imperfect sample models. In the imperfect sample models, one or two layers of corrugated fin structure were replaced by the fin layers made of bent-type cell walls. The localised deformation in the quasi-static imperfect models of cylindrical sample started at the imperfect layers, the same as the tests, and the layers were compressed until about the densification strain in a step-wise fashion. The localised deformation in the perfect models, however, started at the layers at and near the top and bottom of the test sample. In the shock mode, the sample crushed sequentially starting at the impact end layer regardless the perfect or imperfect sample models were used. Furthermore, the perfect and imperfect models resulted in nearly the same initial crushing stresses in the shock mode. The layer strain histories revealed a velocity-dependent layer densification strain. Both model types, the imperfect and perfect, well approximated the stress-time histories and layer deformations of the shock mode. The rigid perfectly plastic locking model based on the numerically determined densification strains also showed well agreements with the experimental and numerical plateau stresses of the shock mode.
  • Article
    Citation - WoS: 4
    Citation - Scopus: 4
    The Effect of Cell Wall Material Strain and Strain-Rate Hardening Behaviour on the Dynamic Crush Response of an Aluminium Multi-Layered Corrugated Core
    (Taylor and Francis Ltd., 2021) Güden, Mustafa; Canbaz, İlker
    The effect of the parameters of the Johnson and Cook material model on the direct impact crushing behaviour of a layered 1050 H14 aluminium corrugated structure was investigated numerically in LS-DYNA at quasi-static (0.0048 m s(-1)) and dynamic (20, 60, 150 and 250 m s(-1)) velocities. Numerical and experimental direct impact tests were performed by lunching a striker bar onto corrugated samples attached to the end of the incident bar of a Split Hopkinson Pressure Bar set-up. The numerical impact-end stress-time and velocity-time curves were further compared with those of rigid-perfectly-plastic-locking (r-p-p-l) model. Numerical and r-p-p-l model impact-end stress analysis revealed a shock mode at 150 and 250 m s(-1), transition mode at 60 m s(-1) and quasi-static homogenous mode at 20 m s(-1). The increase of velocity from quasi-static to 20 m s(-1) increased the numerical distal-end initial peak-stress, while it almost stayed constant between 20 and 250 m s(-1) for all material models. The increased distal-end initial peak-stress of strain rate insensitive models from quasi-static to 20 m s(-1) confirmed the effect of micro-inertia. The numerical models further indicated a negligible effect of used material models on the impact-end stress of investigated structure. Finally, the contribution of strain rate to the distal-end initial peak-stress of cellular structures made of low strain rate sensitive Al alloys was shown to be relatively low as compared with that of strain hardening and micro-inertia, but it might be substantial for the structures constructed using relatively high strain rate sensitive alloys.
  • Article
    Citation - WoS: 19
    Citation - Scopus: 21
    Dynamic Crushing Behavior of a Multilayer Thin-Walled Aluminum Corrugated Core: the Effect of Velocity and Imperfection
    (Elsevier Ltd., 2018) Sarıyaka, Mustafa; Taşdemirci, Alper; Güden, Mustafa
    The crushing behavior of a multilayer 1050 H14 aluminum corrugated core was investigated both experimentally and numerically (LS-Dyna) using the perfect and imperfect models between 0.0048 and 90 m s−1. The dynamic compression and direct impact tests were performed in a compression type and a modified Split Hopkinson Pressure Bar set-up, respectively. The investigated fully imperfect model of the corrugated core sample represented the homogenous distribution of imperfection, while the two-layer imperfect model the localized imperfection. The corrugated core experimentally deformed by a quasi-static homogenous mode between 0.0048 and 22 m s−1, a transition mode between 22 and 60 m s−1 and a shock mode at 90 m s−1. Numerical results have shown that the stress-time profile and the layer crushing mode of the homogeneous and transition mode were well predicted by the two-layer imperfect model, while the stress-time profile and the layer crushing mode were well approximated by the fully imperfect model. The fully imperfect model resulted in complete sequential layer crushing at 75 and 90 m s−1, respectively. The imperfect layers in the shock mode only affected the distal end stresses, while all models implemented resulted in similar impact end stresses. The distal end initial crushing stress increased with increasing velocity until about 22 m s−1; thereafter, it saturated at ~2 MPa, which was ascribed to the micro inertial effect. Both the stress-time and velocity-time history of the rigid-perfectly-plastic-locking model and the critical velocity for the shock deformation were well predicted when a dynamic plateau stress determined from the distal end stresses in the shock mode was used in the calculations.