Mechanical Engineering / Makina Mühendisliği
Permanent URI for this collectionhttps://hdl.handle.net/11147/4129
Browse
6 results
Search Results
Now showing 1 - 6 of 6
Article Gemi Sevk Gücü ve Isı Transferinin Yapısal Gelişim Teorisi ile İlişkisi(TMMOB Gemi Mühendisleri Odası, 2022) Güneş, Ümit; Çetkin, Erdal; Şahin, BahriYapısal Gelişim Teorisi 1996 yılında literatüre kazandırılmış olup tabiattaki ve mühendislikteki tasarım prensiplerini açıklar. Teori, yeryüzündeki akış sistemlerini bütüncül bir şekilde ele alır. Akışın (hareketin) olmadığı yerde çoğu zaman canlılıktan bahsetmemiz dahi mümkün olmamaktadır. Akış sistemlerinin çözümünde anahtar davranış biçimi bu sistemlerin minimum dirençli yol ile hareketini sürdürmesidir. Belli bir zaman dilimi için minimum direnç ile hareket eden sistem zaman geçtikçe kendine yeni yollar (kanallar) bulmakta ya da bazı yolları hiç kullanmayarak yönünü değiştirmektedir. Yapısal Gelişim Teorisi ise hayati öneme sahip olan akış sistemlerinin fiziksel arka planını ortaya koymaktadır. Bu makalede özellikle mühendislik çözümlerinin başında gelen akış sistemlerinin yapısı (gemilerde kurulu ana makine gücü ve ısı transferi örnekleri özelinde) ve Yapısal Gelişim Teorisi’ne göre ilişkisi araştırılmıştır. Bunun için 1085 adet petrol tankeri için DWT ile bu tankerler için gerekli olan güç ilişkisi nonlineer regresyon ile analiz edilmiştir. Sonuç olarak gemilerdeki genel gelişimin ve ısı transferinin yapısal gelişim prensiplerine uygun şekilde gerçekleştiği gösterilmiştir.Article Citation - WoS: 1Citation - Scopus: 2Emergence of Taperedducts in Vascular Designs With Laminar and Turbulent Flows(Begell House, 2014) Çetkin, ErdalHere we show that tapered ducts emerge in volumetrically bathed porous materials to decrease the resistance to the flow in laminar and turbulent flow regimes. The fluid enters the volume from one point and it is distributed to the entire volume. After bathing the volume, it is collected and leaves the volume from another point, i.e., two trees matched canopy to canopy. This paper shows that the flow architecture (i.e., design of the void spaces in a porous material) should be changed to obtain the minimum resistance to the flow as its size increases. Tapering the ducts decreases the order of the transition size, i.e., the size for changing from one construct to another to obtain the minimum pressure drop. The decrease in the pressure drop is 16% and 38% with the tapered ducts when the flow is laminar and turbulent, respectively. In addition, the volume ratios and the shape of the tapered ducts are documented. There is no design existing in nature with diameters of constant size in order to distribute and/or collect heat, fluid, and/or stress such as bones, rivers, veins, and tree branches. The emergence of the tapered ducts in designed porous materials is natural.Article Citation - WoS: 23Citation - Scopus: 24Constructal Branched Micromixers With Enhanced Mixing Efficiency: Slender Design, Sphere Mixing Chamber and Obstacles(Elsevier Ltd., 2019) Çetkin, Erdal; Miguel, Antonio F.Here we uncover the passive micromixer designs with the maximum mixing efficiency under a lesser flow impedance. Three different designs of micromixers were considered for volume constrained systems: branched systems of ducts, branching ducts with sphere mixing chamber and branching ducts with obstacles. The best performing designs, with maximum mixing efficiency and minimum flow impedance, are uncovered numerically by considering three degrees of freedom (ratios between diameters, between lengths, and between length and diameter) under total volume constraint. The mixing efficiency, the flow impedance and the mixer performance (or mixer quality) for all the designs are determined based on numerical results. The results uncover that the branched micromixer should have long mother ducts with larger diameter than daughter ducts. Our results also show that branching ducts with sphere mixing chambers and obstacles also enhance the mixing efficiency but with an additional penalty on flow impedance. Besides, systems with a sphere mixing chamber insertion in the junction between mother and daughter ducts have greater mixing efficiency than systems with embedded obstacles into the mother channel. However, for a given flow impedance, the mixing efficiency is greater for branched systems of ducts than for branching ducts with sphere mixing chamber and with obstacles. For mixer systems built in a space with limited size, branching ducts with sphere mixing chamber may be a good option because they require less space than the other systems. Here new analytical models are also proposed to predict the mixing efficiency and mixer performance based on numerical results. In summary, this paper provides important insights for the designers of micromixer based on Constructal law. (C) 2018 Elsevier Ltd. All rights reserved.Article Citation - WoS: 3Citation - Scopus: 5Constructal Tree-Shaped Designs for Self-Cooling(Edizioni ETS, 2016) Yenigün, Onur; Çetkin, ErdalIn this paper, we show how a plate which is subjected to a heating load can be kept under an allowable temperature. Vascular channels in which coolant fluid flows have been embedded in the plate. Two types of vascular channel designs were compared: radial and tree-shaped. The effects of channel design on the thermal performance for different volume fractions (the fluid volume over the solid volume) are documented. Changing the design from radial to tree-shaped designs decreases the order of pressure drop. Hence increase in the order of the convection coefficient is achieved. However, treeshaped designs do not bath the entire domain. Therefore, we have inserted additional branches at the uncooled regions. Then, we have compared the peak temperatures of radial, traditional tree-shaped and improved tree-shaped designs. The effect of design on the maximum temperature shows that there should be an optimum design for a distinct set of boundary conditions, and this design should be varied as the boundary conditions change. This result is in accord with the constructal law, i.e. the shape should be varied in order to minimize resistances to the flows.Article Citation - WoS: 6Citation - Scopus: 6The Effect of Cavities and T-Shaped Assembly of Fins on Overall Thermal Resistances(International Information and Engineering Technology Association, 2017) Çetin, Eylem; Çetkin, ErdalIn this study, authors show that maximum excess temperature on a heat generating cylindrical solid domain can be minimized with numerically optimized rectangular cavities and T-shaped fins. The effect of the cavities and the fins on overall thermal resistances were compared while their volume fraction in a unit volume element is fixed. Furthermore, the designs correspond to the minimum thermal resistance were uncovered for two types of flows; parallel and cross-flow. The governing equations of the heat transfer and the fluid flow were solved simultaneously in order to show the effects of design on the flow characteristics and the thermal performance. Two-dimensional solution domain was used to uncover the thermal performance in cross-flow case because the flow direction is perpendicular to the heat transfer surface area of the heat generating domain. However, three-dimensional domain was used in parallel flow case because the fluid flows along the outer surface of the heat generating domain. For the cross-flow case, the results show that T-shaped assembly of fins with longer stem and shorter tributaries correspond to the lower peak temperature. In addition, the results also show that there is an optimal cavity shape that minimizes the peak temperature. This optimal shape becomes thinner when the number of the cavities increase. In parallel flow case, fins with thicker and shorter stem and longer tributaries correspond to the minimum excess temperature. In addition, the longer and thinner cavities increase the thermal performance in parallel flow case.Article Citation - WoS: 3Citation - Scopus: 3Constructal vascularized structures(Walter de Gruyter GmbH, 2015) Çetkin, ErdalSmart features such as self-healing and selfcooling require bathing the entire volume with a coolant or/and healing agent. Bathing the entire volume is an example of point to area (or volume) flows. Point to area flows cover all the distributing and collecting kinds of flows, i.e. inhaling and exhaling, mining, river deltas, energy distribution, distribution of products on the landscape and so on. The flow resistances of a point to area flow can be decreased by changing the design with the guidance of the constructal law, which is the law of the design evolution in time. In this paper, how the flow resistances (heat, fluid and stress) can be decreased by using the constructal law is shown with examples. First, the validity of two assumptions is surveyed: using temperature independent Hess-Murray rule and using constant diameter ducts where the duct discharges fluid along its edge. Then, point to area types of flows are explained by illustrating the results of two examples: fluid networks and heating an area. Last, how the structures should be vascularized for cooling and mechanical strength is documented. This paper shows that flow resistances can be decreased by morphing the shape freely without any restrictions or generic algorithms.