Mechanical Engineering / Makina Mühendisliği

Permanent URI for this collectionhttps://hdl.handle.net/11147/4129

Browse

Filters

2015 - 201932020 - 20213

Settings

Institution Author: search.filters.institutionAuthor.Çetkin, ErdalWoS Q: search.filters.wosQuartile.Q3

Search Results

Now showing 1 - 6 of 6
  • Article
    Citation - WoS: 5
    Citation - Scopus: 6
    Asymmetric Y-Shaped Micromixers With Spherical Mixing Chamber for Enhanced Mixing Efficiency and Reduced Flow Impedance
    (Isfahan University of Technology, 2021) Çetkin, Erdal; Miguel, A. F.
    Microfluidic devices have many attractive qualities such as low cost, small size, and in-field use. Micromixers are very important components of these devices because affect their efficiency. In a passive mixer, the structural characteristics of the mixer are crucial and must be analyzed. This paper presents a numerical study of the mixing in passive Y-shaped micromixers with a spherical mixing chamber for a volume constrained system. The effect of asymmetric bifurcated ducts, the angle in between the inflow ducts, eccentricity and, obstacles inserted in the mixing sphere, on the mixing efficiency and flow impedance is evaluated. Vortical structures characteristics and the possible occurrence of engulfment are also identified. The results show that flow impedance (pressure drop for unit volumetric flow rate) can be decreased greatly for the same mixing efficiency as the volume of the spherical mixing chamber is 20% of the total volume. Insertion of the obstacles into the sphere mixing chamber decreases the mixing efficiency while they increase the flow impedance. The results also show that spherical mixing chamber enhances mixing efficiency while decreasing flow impedance if the volume reserved for it is greater than a limit value which depends on the diameter and length scale ratios in between the mother and daughter ducts as well as the total volume. Overall, the paper documents the variation of mixing efficiency and flow impedance based on the geometrical parameters of three-dimensional asymmetric passive micromixer with sphere mixing chamber.
  • Article
    Citation - WoS: 23
    Citation - Scopus: 26
    Thermal Management of Electric Vehicle Battery Cells With Homogeneous Coolant and Temperature Distribution
    (American Institute of Physics, 2020) Göçmen, Sinan; Güngör, Şahin; Çetkin, Erdal
    Electric vehicles play an integral role in eliminating pollution related to transportation, especially if the electricity is generated via renewable sources. However, storing electricity onboard requires many battery cells. If the temperature of the cells is not strictly regulated, their capacity decreases in time, and they may burn or explode due to thermal runaway. Battery thermal management systems emerged for safe operations by keeping the battery cell temperatures under limit values. However, the current solutions do not yield uniform temperature distribution for all the cells in a pack. Here, we document that constant temperature distribution can be achieved with uniform coolant distribution to the channels located between batteries. The design process of the developed battery pack begins with a design used in current packs. Later, how the shape of the distributor channel affects flow uniformity is documented. Then, the design complexity was increased to satisfy the flow uniformity condition, which is essential for temperature uniformity. The design was altered based on a constructal design methodology with an iterative exhaustive search approach. The uncovered constructal design yields a uniform coolant distribution with a maximum of 0.81% flow rate deviation along channels. The developed design is palpable and easy to manufacture relative to the tapered manifold designs. The results also document that the peak temperature difference between the cells decreases from a maximum of 12K to 0.4K. Furthermore, homogenous distribution of air is one of the limiting factors of the development of metal-air batteries. This paper also documents how air can be distributed uniformly to metal-air battery cells in a battery pack.
  • Article
    Citation - WoS: 35
    Citation - Scopus: 38
    Heat Transfer Enhancement in a Microchannel Heat Sink: Nanofluids And/Or Micro Pin Fins
    (Taylor & Francis, 2020) Coşkun, Turgay; Çetkin, Erdal
    Here, we show that overall thermal conductance in a rectangular microchannel heat sink can be maximized with the combination of nanofluids and micro pin fins. We uncover the effect of micro pin fins and nanofluids both separately and simultaneously in order to uncover their effect on the thermal conductance (i.e., thermal resistance). Both nanofluids and micro pin fins decrease the overall thermal resistance due to increase in the average thermal conductivity of the flow system. In addition, they increase the heat transfer surface area of the solid interacting with the fluid. However, the pumping power (pressure drop) increases in both methods due to the increase in the resistances to the fluid flow. The results document what should be the nanoparticle volume fraction mixed into the base fluid and the micro pin fin volume in order to minimize thermal resistance. If the thermal conductivity of the nanoparticles and micro pin fins are the same, the thermal conductance becomes the maximum with 4% and 0.14% volume fractions for the nanofluid and micro pin fins, respectively. This result shows that inserting micro pin fins and using nanofluids with a given volume fraction ratio maximize the overall thermal conductance. © 2019, © 2019 Taylor & Francis Group, LLC.
  • Article
    Citation - WoS: 10
    Citation - Scopus: 10
    Constructal Microdevice Manifold Design With Uniform Flow Rate Distribution by Consideration of the Tree-Branching Rule of Leonardo Da Vinci and Hess-Murray Rule
    (The American Society of Mechanical Engineers(ASME), 2017) Çetkin, Erdal
    In this paper, we show how the design of a microdevice manifold should be tapered for uniform flow rate distribution. The designs based on the tree-branching rule of Leonardo da Vinci and the Hess-Murray rule were considered in addition to the constructal design. Both da Vinci and Hess-Murray designs are insensitive to the inlet velocity, and they provide better flow uniformity than the base (not tapered) design. However, the results of this paper uncover that not only pressure drop but also velocity distribution in the microdevice play an integral role in the flow uniformity. Therefore, an iterative approach was adopted with five degrees-of-freedom (inclined wall positions) and one constraint (constant distribution channel thickness) in order to uncover the constructal design which conforms the uniform flow rate distribution. In addition, the effect of slenderness of the microchannels (Svelteness) and inlet velocity on the flow rate distribution to the microchannels has been documented. This paper also uncovers that the design of a manifold should be designed with not only the consideration of pressure distribution but also dynamic pressure distribution especially for non-Svelte microdevices.
  • Article
    Citation - WoS: 36
    Citation - Scopus: 39
    The Natural Emergence of Asymmetric Tree-Shaped Pathways for Cooling of a Non-Uniformly Heated Domain
    (American Institute of Physics, 2015) Çetkin, Erdal; Oliani, Alessandro
    Here, we show that the peak temperature on a non-uniformly heated domain can be decreased by embedding a high-conductivity insert in it. The trunk of the high-conductivity insert is in contact with a heat sink. The heat is generated non-uniformly throughout the domain or concentrated in a square spot of length scale 0.1 L0, where L0 is the length scale of the non-uniformly heated domain. Peak and average temperatures are affected by the volume fraction of the high-conductivity material and by the shape of the high-conductivity pathways. This paper uncovers how varying the shape of the symmetric and asymmetric high-conductivity trees affects the overall thermal conductance of the heat generating domain. The tree-shaped high-conductivity inserts tend to grow toward where the heat generation is concentrated in order to minimize the peak temperature, i.e., in order to minimize the resistances to the heat flow. This behaviour of high-conductivity trees is alike with the root growth of the plants and trees. They also tend to grow towards sunlight, and their roots tend to grow towards water and nutrients. This paper uncovers the similarity between biological trees and high-conductivity trees, which is that trees should grow asymmetrically when the boundary conditions are non-uniform. We show here even though all the trees have the same objectives (minimum flow resistance), their shape should not be the same because of the variation in boundary conditions. To sum up, this paper shows that there is a high-conductivity tree design corresponding to minimum peak temperature with fixed constraints and conditions. This result is in accord with the constructal law which states that there should be an optimal design for a given set of conditions and constraints, and this design should be morphed in order to ensure minimum flow resistances as conditions and constraints change.
  • Article
    Citation - WoS: 13
    Citation - Scopus: 15
    Constructal Vascular Structures With High-Conductivity Inserts for Self-Cooling
    (The American Society of Mechanical Engineers(ASME), 2015) Çetkin, Erdal
    In this paper, we show how a heat-generating domain can be cooled with embedded cooling channels and high-conductivity inserts. The volume of cooling channels and high-conductivity inserts is fixed, so is the volume of the heat-generating domain. The maximum temperature in the domain decreases with high-conductivity inserts even though the coolant volume decreases. The locations and the shapes of high-conductivity inserts corresponding to the smallest peak temperatures for different number of inserts are documented,