Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
9 results
Search Results
Article Comprehensive 4E Analysis, Multi-Objective Optimization, and Feasibility Study of Five Natural Gas Liquefaction Processes With a Case Study for Iran(Elsevier Sci Ltd, 2026) Basmenj, Farhad Rahmdel; Tabriz, Zahra Hajimohammadi; Aghdasinia, Hassan; Mohammadpourfard, MousaNatural gas (NG) is increasingly vital as a cleaner energy source due to its lower carbon emissions compared to other fossil fuels. Liquefaction facilitates efficient long-distance transportation. While numerous studies address NG liquefaction's technical aspects, holistic research remains limited. This study presents a comprehensive evaluation of five conventional natural gas (NG) liquefaction processes (including SMR-Linde, SMR-APCI, C3MRLinde, DMR-APCI, and MFC-Linde) through a 4E framework: energy, exergy, exergoeconomic, and exergoenvironmental analyses. Addressing limitations in prior research, it incorporates environmental considerations and introduces production volume-independent metrics to ensure equitable comparisons. Multi-objective optimization, based on exergoeconomic and exergoenvironmental criteria, is employed to identify Pareto-optimal operating conditions. To accelerate this complex process, neural networks are utilized. The study concludes with a feasibility assessment of large-scale LNG production in Iran, offering practical insights for optimizing process selection and enhancing the economic and environmental viability of LNG technologies. Simulations show that the MFC-Linde cycle as the most efficient regarding specific energy consumption (0.2563 kWh/kgLNG), coefficient of performance (3.184), and exergy efficiency (52.32 %). It also demonstrates the lowest unit exergy cost (3.67$/GJ) and exergy unit environmental impact (5271.86mPts/GJ). Multi-objective optimization, considering both exergetic-economic and exergetic-environmental criteria, using neural networks and genetic algorithms in MATLAB identifies Pareto-optimal conditions for all processes. For the MFCLinde, as the most efficient process, optimal operating conditions in the exergetic-economic trade off scenario are: Exergy efficiency of process = 51.45% and Exergy cost rate of LNG = 82, 162.15$/h; at Pressure of NG feed = 5, 925.32kPa, Pressure drop in valve = 5, 831.99kPa, and NG side temperature in heat exchanger = -168.34 degrees C. Finally, a feasibility study for large-scale LNG (Liquefied Natural Gas) production in Iran shows promising results, with a return on investment of 32.24 %/year and a payback period of 2.34 years, indicating the project's potential success in regions with abundant NG reserves.Article Citation - WoS: 22Citation - Scopus: 24Design, Evaluation, and Optimization of an Integrated Proton Exchange Membrane and Double Flash Geothermal Based Organic Rankine Cycle Multi-Generation System Fed by a Biomass-Fueled Gasifier(Elsevier, 2024) Taheri, Muhammad Hadi; Seker, Utku; Akkurt, Gulden Gokcen; Mohammadpourfard, MousaThis study introduces an innovative approach by formulating and evaluating a synergistic biomass-geothermal structure, emphasizing optimized inter-component connections. The research stands out for its thorough analysis of parameter impacts on the system and variables, addressing an unexplored aspect in integrated energy systems. The multi-generation systems are the integration of a combined gasification gas turbine cycle, double flash geothermal cycle, and proton exchange membrane cycle for the generating power and hydrogen. The overall system and its subsystems are studied to explore how the performance of thermodynamics and the total cost rate are influenced by operating parameters. The best operational conditions for both subsystems and the overall system have been determined by analyzing the impact of operating parameters on the thermodynamic behavior and environmental impact through parametric studies. The findings indicate while Sabalan's current efficiency is 16.26 %, the system energy efficiency reached 24.89 % when coupled with other renewable source. To enhance the system's efficiency, a genetics algorithm was utilized to simultaneously optimize the total cost of exergy destruction and investment cost. The outcome of the multi-objective optimization revealed that the exergy efficiency of optimal point for the system is 29.8 % and a total investment cost is 6 (M$/year).Article Citation - WoS: 8Citation - Scopus: 11Design, Thermodynamic and Economic Evaluation, and Optimization of Gasoline Production From Refinery Furnaces Flue Gas(Elsevier, 2023) Nazerifard, Reza; Mohammadpourfard, Mousa; Heris, Saeed ZeinaliIn this paper, the conversion of refinery furnaces’ flue gas into gasoline through the MTG process is investigated. This approach not only reduces greenhouse gas emissions, but also produces a high-value product, providing economic incentives to adopt this technology. The proposed integrated system comprises an organic Rankine cycle, an amine-based carbon capture unit, a methanol synthesis unit, and an MTG unit. In this study, we evaluated the technical and economic aspects of this conversion process, including the thermodynamic and cost analysis, to assess its viability as a sustainable solution for mitigating CO2 emissions from refineries. Also, using response surface methodology combined with the Box-Behnken design, the proposed integrated system was optimized to minimize the gasoline production cost. The thermodynamic assessment concludes that the energy and exergy efficiencies of the overall system are 73.12% and 85.24%, respectively. The proposed system yields an annual gasoline production rate of >184 million liters. The estimated total capital investment for the proposed system is 172.16 M$, which the methanol synthesis unit with a share of 48.65% is the most expensive one. The results give a gasoline production cost of 1.58 $/kg or 4.28 $/gal for the optimized case. Also, hydrogen has the highest contribution in the production cost, so with a 20% decrease in the price of hydrogen, the production cost of gasoline decreases by 18.71%. With this rate of technological improvement, reductions in the price of hydrogen seem inevitable in not-so-distant years, which makes the proposed system of converting refinery furnaces’ flue gas into gasoline became desirable. © 2023 Elsevier LtdReview Citation - WoS: 21Citation - Scopus: 23A Comprehensive Review of Computational Fluid Dynamics Simulation Studies in Phase Change Materials: Applications, Materials, and Geometries(Springer, 2023) Soodmand, A. Mohammadian; Azimi, B.; Nejatbakhsh, S.; Pourpasha, H.; Farshchi, M. Ebrahimi; Aghdasinia, H.; Mohammadpourfard, Mousa; Heris, S. ZeinaliThermal energy storage systems (TESS) have emerged as significant global concerns in the design and optimization of devices and processes aimed at maximizing energy utilization, minimizing energy loss, and reducing dependence on fossil fuel energy for both environmental and economic reasons. Phase change materials (PCMs) are widely recognized as promising candidates due to their high latent heat storage (LHS) capacity. This review thoroughly evaluates the computational fluid dynamics (CFD) studies conducted in various sections, encompassing materials, modeling, simulation, as well as the results, advantages, and disadvantages of these works. The study is organized into three distinct sections. The first section discusses the applications of PCMs in various areas, including lithium-ion batteries, solar applications, building applications, electronics, and heating and cooling systems. The second section provides a comprehensive summary of cylindrical, rectangular, spherical, arbitrary shapes, and packed-bed geometries employed in TESS. The third section investigates the different types of materials used as PCMs. Based on the findings of this study, it can be concluded that industrial applications of hybrid nanocomposites incorporating PCMs in different geometries pose challenges, particularly in three-dimensional (3D) settings, where instability becomes a significant concern. Hence, further research and investigation are necessary to address these challenges adequately. In conclusion, this study serves as a reference review for future research endeavors in the field of simulating various PCMs in different geometries and applications. It provides valuable insights into the current state of knowledge, highlights potential areas for improvement, and offers guidance for advancing simulation techniques related to PCMs.Article Citation - WoS: 103Citation - Scopus: 113Preparation and Characterizations of Tio2/Zno Nanohybrid and Its Application in Photocatalytic Degradation of Tetracycline in Wastewater(Elsevier, 2023) Zeinali Heris, Saeed; Etemadi, Martin; Mousavi, Seyed Borhan; Mohammadpourfard, Mousa; Ramavandi, BahmanThe photodegradation of tetracycline antibiotics (TC) in an aqueous solution, using the TiO2 nanoparticles, ZnO microparticles, and TiO2/ZnO composite under the UV lamp in a continuous reactor, was performed. The effects of different parameters, such as the initial TC concentration, medium pH, ratio of each photocatalyst, and the flow rate were comprehensively studied. SEM, EDX, and XRD characterization techniques were employed to study the morphology and structure features of the prepared composite. The results revealed that a more significant amount of TC is not easily removed from wastewater. Furthermore, by increasing the pH of the medium to 11, the efficiency of TC degradation was increased, while the amount of removal remained stable at higher pH values. As the flow rate increased up to 190 mL/min, the removal efficiency increased; however, at higher flow rates, lower efficiency was obtained. Moreover, using multivariate analysis and response surface methodology (RSM), a model for removing TC and the effect of experimental parameters on removal efficiency was proposed. The optimal conditions using the RSM method were found to be the reduction efficiency of 78.94 % in pH = 11 (flow rate of 132 mL/min, and TiO2 concentration of 323 mg) and reduction efficiency of 75.89% in pH = 9 (flow rate of 143.19 mL/min and TiO2 concentration of 312.73 mg). © 2023 Elsevier B.V.Book Part Citation - Scopus: 4Investigation of a New Methanol, Hydrogen, and Electricity Production System Based on Carbon Capture and Utilization(Springer, 2023) Khani, Leyla; Mohammadpourfard, MousaIt is well-known that clean energy transition requires low carbon emission. The increase in population, economic development, and human welfare demands has led to a rise in energy consumption, mainly supplied by fossil fuels. However, burning fossil fuels produces carbon dioxide, which is a greenhouse gas and a contributor to environmental problems. Therefore, carbon capture and conversion to different products have gained attention. On the other hand, combining two or more different thermodynamic systems for simultaneous production of various demands from one energy source looks reasonable. In this regard, a new trigeneration system is proposed to decrease atmospheric carbon dioxide emission and produce methanol, hydrogen, and power. A flue gas stream with a defined composition, solar energy, and atmospheric air are the system’s inlets. Then, mass, energy, and exergy balance equations are applied for each subsystem to investigate the system’s thermodynamic performance. Also, the effect of changing operating parameters on the performance of each subsystem is studied. © 2023, The Author(s), under exclusive license to Springer Nature Switzerland AG.Book Part Citation - Scopus: 1A New Stable Solar System for Electricity, Cooling, Heating, and Potable Water Production in Sunny Coastal Areas(Springer, 2023) Khani, Leyla; Mohammadpourfard, MousaNowadays, more attention is paid to provide clean energy products with low environmental pollution in a decentralized way. Many coastal rural areas suffer from freshwater and electricity scarcity, especially in hot weather condition. Meanwhile, these regions have a great access to intense solar radiation and seawater. Hence, it seems logical to use the available solar energy in those places to provide to necessities like power, heating, and cooling. A new solar cooling, power, heating, and freshwater production system is designed, evaluated, and optimized in this research. The proposed system is composed of several subsystems to generate each product with high efficiency and reliability. Solar energy is unavailable at night, so molten salt energy storage is used to establish the steady operation of the system. Then, the system is evaluated from thermodynamic and exergoeconomic viewpoints, and a parametric study is accomplished to study the effect on the system performance of key variables. In the end, the system is optimized to determine its best operating condition for different cases. © 2023, The Author(s), under exclusive license to Springer Nature Switzerland AG.Article Citation - WoS: 7Citation - Scopus: 7Comprehensive Thermoeconomic Study of a New Solar Thermosyphon-Assisted Multigeneration System(Elsevier, 2023) Anamaq, Rasoul Najafi; Khani, Leyla; Mohammadpourfard, Mousa; Heris, Saeed Zeinali; Gökçen Akkurt, GüldenNowadays, due to the global energy crisis, limited reservoirs of fossil fuels, and their negative environmental effects, the use of renewable energy sources and multigeneration systems have become good alternatives for conventional thermodynamic systems. One of these resources, whose technology has developed rapidly in recent years, is the use of solar energy for the simultaneous generation of various products. Therefore, in this research, a multigeneration system with several subsystems is introduced. The proposed system includes a solar energy collector to receive thermal energy, two thermal energy storage tanks, an organic Rankine cycle, and a Kalina cycle to generate electricity, a multi-effect distillation unit to produce fresh water, an electrolyzer to produce hydrogen, as well as heat recovery for hot water and hot air generation. In this multigeneration system, the cooling unit is designed with the help of a thermosyphon. The performance of the proposed system is studied from energy, exergy, environmental, and exergoeconomic viewpoints using Aspen HYSYS and EES software. The obtained results show that due to the addition of the thermosyphon unit to the refrigeration system, the exergy efficiency increases from 55.62% to 70.26%. As a result of this combination, the performance of the whole system is improved and the amount of costs are reduced. In addition, the parabolic collector system has the highest exergy destruction ratio, 39%, among the subsystems. Furthermore, the results of the exergoeconomic analysis indicate that the PEM water heater with 33.3% and the ejector with 22.7% own the highest cost destruction rates.Article Citation - WoS: 45Citation - Scopus: 31Highly Efficient Treatment of Petrochemical Spent Caustic Effluent Via Electro-Fenton Process for Cod and Toc Removal: Optimization and Experimental(Springer, 2023) Gholami, Asma; Mousavi, Seyed Borhan; Heris, Saeed Zeinali; Mohammadpourfard, MousaCaustic is commonly used in oil and gas refineries to remove CO2, H2S, organic sulfur, and acidic compounds; however, spent caustic must be treated considering the type of wastewater in refinery and petrochemical units due to their hazardous characteristics. This research aims to reduce the chemical oxygen demand (COD) and the total organic carbon (TOC) from the used caustic effluent of the olefin unit of Ilam Petrochemical Company employing the electro-Fenton method. The affecting parameters, such as H2O2 concentration, reaction time, pH, and current density on the COD and TOC removal rate, were investigated. An experimental design by response surface methodology (RSM) based on the Box–Behnken method with the considered factors was considered to study the setup’s effectiveness and optimize the conditions. The outcomes revealed that by increasing the H2O2 concentration from 11 to 18 mgL, the COD removal efficiency was enhanced from 68 to 93%. On the other hand, by increasing the reaction time after 15 min, the COD and TOC removal efficiency decreased. The same trend was observed by increasing the current density after the optimal value. The optimal conditions were acquired at pH = 4, current density = 20 mAcm2, H2O2 concentration = 18 mgL, and reaction time = 15 min. The promising results confirmed that the electro-Fenton could be an excellent treatment technique in Ilam Petrochemical Unit as a spent caustic treatment. © 2023, The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.