Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
16 results
Search Results
Article Citation - WoS: 10Citation - Scopus: 12Novel Hybrid Adsorption-Electrodialysis (aded) System for Removal of Boron From Geothermal Brine(American Chemical Society, 2022) Altınbaş, Bekir Fırat; Orak, Ceren; Ökten, Hatice Eser; Yüksel, AslıA novel hybrid adsorption-electrodialysis (AdED) system to remove environmentally harmful boron from geothermal brine was designed and effective operating parameters such as pH, voltage, and flow rate were studied. A cellulose-based adsorbent was synthesized from glycidyl methacrylate (GMA) grafted cellulose and modified with a boron selective n-methyl-d-glucamine (NMDG) group and characterized with SEM-EDX, FT-IR, and TGA analyses. Batch adsorption studies revealed that cellulose-based adsorbent showed a remarkable boron removal capacity (19.29 mg/g), a wide stable operating pH range (2-10), and an adsorption process that followed the Freundlich isotherm (R2= 0.95) and pseudo-second-order kinetics (R2= 0.99). In the hybrid AdED system, the optimum operating parameters for boron removal were found to be a pH of 10, a voltage of 10 V, a flow rate of 100 mL/min, and an adsorbent dosage of 4 g/L. The presence of the adsorbent in the hybrid system increased boron removal from real geothermal brine (containing 199 ppm boron) from 7.2% to 73.3%. The results indicate that the designed AdED system performs better than bare electrodialysis for boron removal from ion-rich real geothermal brine while utilizing environmentally friendly cellulose-based adsorbent.Article Citation - WoS: 31Citation - Scopus: 35Electrochemical Degradation of Methylene Blue by a Flexible Graphite Electrode: Techno-Economic Evaluation(American Chemical Society, 2022) Gören, Ayşegül Yağmur; Recepoğlu, Yaşar Kemal; Edebali, Özge; Şahin, Çağrı; Genişoğlu, Mesut; Ökten, Hatice EserIn this study, electrochemical removal of methylene blue (MB) from water using commercially available and low-cost flexible graphite was investigated. The operating conditions such as initial dye concentration, initial solution pH, electrolyte dose, electrical potential, and operating time were investigated. The Box-Behnken experimental design (BBD) was used to optimize the system's performance with the minimum number of tests possible, as well as to examine the independent variables' impact on the removal efficiency, energy consumption, operating cost, and effluent MB concentration. The electrical potential and electrolyte dosage both improved the MB removal efficiency, since increased electrical potential facilitated production of oxidizing agents and increase in electrolyte dosage translated into an increase in electrical current transfer. As expected, MB removal efficiency increased with longer operational periods. The combined effects of operating time-electrical potential and electrical potential-electrolyte concentration improved the MB removal efficiency. The maximum removal efficiency (99.9%) and lowest operating cost (0.012 $/m3) were obtained for initial pH 4, initial MB concentration 26.5 mg/L, electrolyte concentration 0.6 g/L, electrical potential 3 V, and operating time 30 min. The reaction kinetics was maximum for pH 5, and as the pH increased the reaction rates decreased. Consequent techno-economic assessment showed that electrochemical removal of MB using low-cost and versatile flexible graphite had a competitive advantage.Article Citation - WoS: 40Citation - Scopus: 47Boron in Geothermal Energy: Sources, Environmental Impacts, and Management in Geothermal Fluid(Elsevier, 2022) Mott, A.; Baba, Alper; Hadi Mosleh, Mojgan; Ökten, Hatice Eser; Babaei, Masoud; Gören, Ayşegül Yağmur; Feng, C.; Recepoğlu, Yaşar Kemal; Uzelli, Taygun; Uytun, Hüseyin; Morata, Diego; Yüksel Özşen, AslıThe problem of hazardous chemicals in geothermal fluid is a critical environmental concern in geothermal energy developments. Boron is among the hazardous contaminants reported to be present at high concentrations in geothermal fluids in various countries. Poor management and inadequate treatment of geothermal fluids can release excessive boron to the environment that has toxic effects on plants, humans, and animals. Despite the importance of boron management in geothermal fluid, limited and fragmented resources exist that provide a comprehensive understanding of its sources, transport and fate, and the treatment strategies in geothermal energy context. This paper presents the first critical review from a systematic and comprehensive review on different aspects of boron in geothermal fluid including its generation, sources, toxicity, ranges and the management approaches and treatment technologies. Our research highlights the origin of boron in geothermal water to be mainly from historical water-rock interactions and magmatic intrusion. Excessive concentrations of boron in geothermal fluids have been reported (over 500 mg/L in some case studies). Our review indicated that possible boron contamination in geothermal sites are mostly due to flawed construction of production/re-injection wells and uncontrolled discharge of geothermal water to surface water. The dominancy of non-ionic H3BO3 species makes the selection of the suitable treatment method for geothermal waters limited. Combining boron selective resins and membrane technologies, hybrid systems have provided effluents suitable for irrigation. However, their high energy consumption and course structure of boron selective resins encourage further research to develop cost-effective and environmentally friendly alternatives.Article Citation - WoS: 13Citation - Scopus: 14Desalination and Detoxification of Textile Wastewater by Novel Photocatalytic Electrolysis Membrane Reactor for Ecosafe Hydroponic Farming(MDPI, 2022) Aydın, Muhammed Iberia; Özaktaç, Damla; Yüzer, Burak; Doğu, Mustafa; İnan, Hatice; Ökten, Hatice Eser; Coşkun, Serdar; Selçuk, HüseyinIn this study, a novel photoelectrocatalytic membrane (PECM) reactor was tested as an option for the desalination, disinfection, and detoxification of biologically treated textile wastewater (BTTWW), with the aim to reuse it in hydroponic farming. The anionic ion exchange (IEX) process was used before PECM treatment to remove toxic residual dyes. The toxicity evaluation for every effluent was carried out using the Vibrio fischeri, Microtox® test protocol. The disinfection effect of the PECM reactor was studied against E. coli. After PECM treatment, the 78.7% toxicity level of the BTTWW was reduced to 14.6%. However, photocatalytic desalination during treatment was found to be slow (2.5 mg L-1 min-1 at 1 V potential). The reactor demonstrated approximately 52% COD and 63% TOC removal efficiency. The effects of wastewater reuse on hydroponic production were comparatively investigated by following the growth of the lettuce plant. A detrimental effect was observed on the lettuce plant by the reuse of BTTWW, while no negative impact was reported using the PECM treated textile wastewater. In addition, all macro/micronutrient elements in the PECM treated textile wastewater were recovered by hydroponic farming, and the PECM treatment may be an eco-safe wastewater reuse method for crop irrigation.Article Citation - WoS: 33Citation - Scopus: 37Energy Production From Treatment of Industrial Wastewater and Boron Removal in Aqueous Solutions Using Microbial Desalination Cell(Elsevier, 2021) Gören, Ayşegül Yağmur; Ökten, Hatice EserAs a result of a much needed paradigm shift worldwide, treated saline water is being considered as a viable option for replacing freshwater resources in agricultural irrigation. Vastly produced geothermal brine in Turkey may pose a significant environmental risk due to its high ionic strength, specifically due to boron. Boron species, which are generally found uncharged in natural waters, are costly to remove using high-throughput membrane technologies such as reverse osmosis. Recent advances in bioelectrochemical systems (BES) has facilitated development of energetically self-sufficient wastewater treatment and desalination. In this study, removal of boron from synthetic solutions and real geothermal waters, along with simultaneous energy production, using the microbial desalination cell (MDC) were investigated. Optimization studies were conducted by varying boron concentrations (5, 10, and 20 mg L-1), air flow rates (0, 1, and 2 L min(-1)), electrode areas (18, 24, 36, and 72 cm(2)), catholyte solutions, and operating modes. Even though the highest concentration decrease was observed for 20 mg-B L-1, 5 mg-B L-1 concentration experiment gave the closest result to the 2.4 mg-B L-1 limit value asserted by WHO. Effect of electrode surface area was proven to be significant on boron removal efficiency. Employing the optimum conditions acquired with synthetic solutions, boron and COD removal efficiencies from real geothermal brine were 44.3% and 90.6%, respectively. MDC, being in its early levels of technology readiness, produced promising desalination and energy production results in removal of boron from geothermal brine.Article Citation - Scopus: 5Effect of Covid-19 Pandemic on Ambient Air Quality and Excess Risk of Particulate Matter in Turkey(2021) Gören, Ayşegül Yağmur; Genişoğlu, Mesut; Ökten, Hatice Eser; Sofuoğlu, Sait CemilThe COVID-19 pandemic, which has reached 4 million global cases as of March 10, 2020, has become a worldwide problem. Turkey is one of the most affected (9th in the world) country with 139 771 cases. An intermittent curfew policy that differ for three age groups, and an intercity travel ban varying within the country have been implemented. The effects of changes in social life and industrial activity in terms of environmental pollution are not yet known. The short-term effects on PM2.5, PM10, SO2, NO2, NO, NOx, O3 and CO concentrations measured at 51 air quality measurement stations (AQMS) in 11 cities in March – April period of 2020 were statistically compared with that of the previous year. While PM2.5 (9/14 AQMS) and PM10 (29/35 AQMS) concentrations were not significantly affected, NO (12/24 AQMS), NO2 (20/29 AQMS), NOX (17/25 AQMS) concentrations were decreased, SO2 concentrations at half of the AQMSs (11/25) did not show a significant change. There were stations at which higher pollutant concentrations were measured in the study period in 2020 compared to that of 2019. Excess risks associated with PM2.5 and PM10 were estimated to be variable, albeit with a small difference. In conclusion, the heterogeneous actions taken in response to the COVID-19 pandemic resulted in mixed effects on ambient air quality.Editorial Special Issue on the 4th International Conference on Recycling and Reuse 24–26 October 2018, Istanbul, Turkey: Preface(Elsevier B.V., 2019) Okten, H.E.; Ökten, Hatice Eser; Balkaya, N.; Aydin, S.; Elmaslar, E.; Ongen, A.; Selcuk, H.[No abstract available]Article Citation - WoS: 8Citation - Scopus: 12A Box–behnken Design (bbd) Optimization of the Photocatalytic Degradation of 2,4-Dichlorophenoxyacetic Acid (2,4-D) Using Tio2/H2o2(Desalination Publications, 2018) Doğdu Okçu, Gamze; Baldan Pakdil, Nazlı; Ökten, Hatice Eser; Yalçuk, Arda2,4-Dichlorophenoxyacetic acid (2,4-D), a chlorinated phenoxy-alkanoic herbicide, is used extensively in agriculture. This work investigates TiO2/H2O2 mediated UV photocatalytic degradation of 2,4-D in a laboratory-scale photoreactor. Three levels of Box–Behnken design technique, combined with response surface methodology (RSM), were used to design the experiments. Two kinds of multivariate experimental design (pH, TiO2, and 2,4-D concentration) and (pH, TiO2, and H2O2 concentrations) were employed to establish two quadratic models (Model 1 and Model 2), showing the functional relationship between degradation rate of 2,4-D and three independent experimental parameters. Model 1 predicted optimum values for pH, TiO2, and 2,4-D concentrations to be 5.7, 1.20 g L−1, and 32 mg L−1, respectively. Model 2 predicted optimum values for pH, TiO2, and initial H2O2 concentrations to be 4.94, 1.34 g L−1, and 161 mg L−1. Degradation rate of 2,4-D approached 78.10% for Model 1 and 83.63% for Model 2. For both models, similar results were obtained through optimizing variables by RSM and using single factorial batch reactor operation. Regression analysis showed good agreement between experimental results and predictive values for Models 1 and 2, with R2 values of 0.9958 and 0.9976, respectively.Article Citation - WoS: 12Citation - Scopus: 14Thermodynamically Designed Target-Specific Dna Probe as an Electrochemical Hybridization Biosensor(Elsevier Ltd., 2020) Can, Faruk; Ökten, Hatice Eser; Ergön Can, Tülay; Ergenekon, Pınar; Özkan, Melek; Erhan, ElifApplications of molecular techniques to elucidate identity or function using biomarkers still remain highly empirical and biosensors are no exception. In the present study, target-specific oligonucleotide probes for E. coli K12 were designed thermodynamically and applied in an electrochemical DNA biosensor setup. Biosensor was prepared by immobilization of a stem–loop structured probe, modified with a thiol functional group at its 5′ end and a biotin molecule at its 3′ end, on a gold electrode through self-assembly. Mercaptopropionic acid (MPA) was used to optimize the surface probe density of the electrode. Hybridization between the immobilized probe and the target DNA was detected via the electrochemical response of streptavidin-horseradish peroxidase in the presence of the substrate. The amperometric response showed a linear relationship with the target DNA concentration, ranging from 10 and 400 nM, with a correlation coefficient of 0.989. High selectivity and good repeatability of the biosensor showed that the thermodynamic approach to oligonucleotide probe design can be used in development of electrochemical DNA biosensors.Article Citation - WoS: 5Citation - Scopus: 5A Hybrid Process for 2,4-Dichlorophenoxy Acetic Acid Herbicidal Treatment and Its Microbial Identification by Maldi-Tof Mass Spectrometry(Taylor and Francis Ltd., 2020) Doğdu Okçu, Gamze; Ökten, Hatice Eser; Yalçuk, ArdaThe feasibility of coupling photocatalysis and a biological treatment to remove a herbicide–2,4-dichlorophenoxy acetic acid (2,4-D)–from pure water was examined using batch experiments following three protocols: aerated (A-BR) and non-aerated biodegradation (NA-BR) alone, and intimately combined photodegradation and biodegradation (P-B). In view of a subsequent biological treatment, 15 and 180 min irradiation times were chosen in accordance with spectrophotometric and LC-MS/MS results that indicated the decrease in the COD/TOC ratio during photocatalysis. Pre-treatment led to a quick decrease in concentration of 2,4-D and COD during the biological process: a 78.79 ± 0.30% COD removal and 38.23 ± 3.12% 2,4-D elimination was measured after 5760 min in A-BR, and 80.89 ± 0.81% COD and 81.36 ± 1.37% 2,4-D removal was achieved after 2880 min in P-B. For species identification using matrix-assisted laser desorption/ionization (MALDI)-time of flight (TOF)-TOF/MS equipment, Aeromonas eucrenophila, Stenotrophomonas acidaminiphila, Ralstonia pickettii, Sphingobacterium multivorum and Acinetobacter towneri were identified with high accuracy, and they play important roles in the degradation of 2,4-D.