Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
16 results
Search Results
Article Citation - WoS: 38Citation - Scopus: 43Quantitative Evaluation of the Damage To Rc Buildings Caused by the 2023 Southeast Turkey Earthquake Sequence(SAGE Publications, 2024) Pujol, Santiago; Bedirhanoğlu, İdris; Dönmez, Cemalettin; Dowgala, Jeffrey D.; Eryılmaz Yıldırım, Meltem; Klaboe, Kari; Köroğlu, Fahri Baran; Lequesne, Rémy D.; Öztürk, Baki; Pledger, Liam; Sönmez, EgemenData from 15 earthquakes that occurred in 12 different countries are presented showing that, without better drift control, structures built with building codes allowing large seismic drifts are likely to keep leaving a wide wake of damage ranging from cracked partitions to building overturning. Following the earthquake sequence affecting southeast Turkey in 2023, a team led by Committee 133 of the American Concrete Institute surveyed nearly 250 reinforced concrete buildings in the area extending from Antakya to Malatya. Buildings ranging from 2 to 16 stories were surveyed to assess their damage and evaluate the robustness of their structures in relation to overall stiffness, as measured by the relative cross-sectional areas of structural walls and columns. The majority of the buildings were estimated to have been built in the past 10 years. Yet, the structures surveyed were observed to have amounts of structural walls and columns comparable with amounts reported after the Erzincan (1992), Duzce (1999), and Bingol (2003) Earthquakes in Turkey. These amounts are, on average, much smaller than the wall and column amounts used in Chile and Japan. Because of that lack of robustness and given the intensities of the motions reported from Antakya to Malatya (with 10 stations with peak ground velocity (PGV) of 100 cm/s or more), it is concluded that structures in this region experienced large drifts. Excessive drift (1) exposed a myriad of construction and detailing problems leading to severe structural damage and collapse, (2) induced overturning caused by p-delta for some buildings, and (3) caused widespread damage to brittle masonry partitions. The main lesson is simple: ductility is necessary but not sufficient. It is urgent that seismic drift limits are tightened in high-seismicity regions worldwide. © The Author(s) 2024.Article Citation - WoS: 4Citation - Scopus: 5An Evaluation of the Relationship Between Everyday Life Rhythms and Urban Morphology: the Square of Bursa Kent Meydani Shopping Center, Turkey(SAGE Publications, 2022) Gümüş, İmran; Yılmaz, EbruThe aim of this study is to search for the relationship between the morphological character of urban space and the rhythms of everyday life. Initially, behavioral maps are created by observing daily life rhythms, video recordings are taken on weekend and weekday, the snapshot technique, video recordings, and the pedestrian count analysis are used. In the second step, morphological analyses of the study area are prepared by using space syntax approach. Connectivity, local, and global integration values are obtained through creating axial map, and, in addition, visibility graph analysis (VGA) is performed. Bursa Kent Meydani Shopping Center (BKMSC) consists of a square and the shopping units surrounding it. This area was the main transportation point as Central Bus Station Complex until 2006. The area was selected within the scope of the study because its changing public use due to the functional transformation of the area plays a significant role in the identity of the Bursa. The behavioral maps obtained from the observational data give information about user mobility, various actions, and the activities' locations on weekends and weekdays. By correlating and comparing behavioral and space syntax maps analyses, the relationship between the rhythmic character and the morphological structure of the urban space is tested. The study presents original data by revealing the effects of the morphological elements of Bursa on the daily rhythms of the square of BKMSC. The case study is limited to the surveys conducted in 2 days and three different times of the day. The relationship between observational data and space syntax data shows that daily life rhythms are not independent of the morphological factors.Article Citation - WoS: 14Citation - Scopus: 14Development of Biological Meniscus Scaffold: Decellularization Method and Recellularization With Meniscal Cell Population Derived From Mesenchymal Stem Cells(SAGE Publications, 2021) Kara, Aylin; Koçtürk, Semra; Bilici, Gökçen; Havıtçıoğlu, HasanTissue engineering approaches which include a combination of cells and scaffold materials provide an alternative treatment for meniscus regeneration. Decellularization and recellularization techniques are potential treatment options for transplantation. Maintenance of the ultrastructure composition of the extracellular matrix and repopulation with cells are important factors in constructing a biological scaffold and eliminating immunological reactions. The aim of the study is to develop a method to obtain biological functional meniscus scaffolds for meniscus regeneration. For this purpose, meniscus tissue was decellularized by our modified method, a combination of physical, chemical, and enzymatic methods and then recellularized with a meniscal cell population composed of fibroblasts, chondrocytes and fibrochondrocytes that obtained from mesenchymal stem cells. Decellularized and recellularized meniscus scaffolds were analysed biochemically, biomechanically and histologically. Our results revealed that cellular components of the meniscus were successfully removed by preserving collagen and GAG structures without any significant loss in biomechanical properties. Recellularization results showed that the meniscal cells were localized in the empty lacuna on the decellularized meniscus, and also well distributed and proliferated consistently during the cell culture period (p < 0.05). Furthermore, a high amount of DNA, collagen, and GAG contents (p < 0.05) were obtained with the meniscal cell population in recellularized meniscus tissue. The study demonstrates that our decellularization and recellularization methods were effective to develop a biological functional meniscus scaffold and can mimic the meniscus tissue with structural and biochemical features. We predict that the obtained biological meniscus scaffolds may provide avoidance of adverse immune reactions and an appropriate microenvironment for allogeneic or xenogeneic recipients in the transplantation process. Therefore, as a promising candidate, the obtained biological meniscus scaffolds might be verified with a transplantation experiment.Article Citation - WoS: 16Citation - Scopus: 17Investigation of the High Temperature Dry Sliding Wear Behavior of Graphene Nanoplatelets Reinforced Aluminum Matrix Composites(SAGE Publications, 2021) Martin, Seçkin; Kandemir, Sinan; Antonov, M.In this study, graphene nanoplatelets (GNPs) with a thickness of 50-100 nm have been utilized to improve the mechanical and tribological properties of A360 alloy due to their extraordinary mechanical properties and solid lubricant nature. For the investigation of tribological properties, ball-on disc tests were carried out at various temperatures including room temperature (RT), 150 °C, and 300 °C. According to the hardness and ball-on-disc test results, the nanocomposite samples reinforced with GNPs exhibited improved hardness and wear resistance. The improvement in the wear behavior of nanocomposites was referred to the temporarily formed solid lubricant film of harder GNPs during the wear, and hence coefficient of friction (COF) and volume loss were considerably reduced. Abrasive-adhesive, oxidative, and mild-to-severe were found to be main wear mechanisms at RT, 150 °C, and 300 °C, respectively. Overall, the results show that the nanocomposites fabricated by casting method combined with mechanical stirring and ultrasonication have promising wear performance, especially at elevated temperatures. This may suggest that these developed materials could be potential candidates to be used in the engineering applications requiring high temperature wear performance. © The Author(s) 2020.Article Citation - WoS: 37Citation - Scopus: 41Determination of Olive Oil Adulteration With Vegetable Oils by Near Infrared Spectroscopy Coupled With Multivariate Calibration(SAGE Publications, 2010) Öztürk, Betül; Yalçın, Ayşegül; Özdemir, DurmuşThere has been growing public awareness about the health benefits of olive oil throughout the world in recent years, resulting in a significant increase in its consumption as part of the daily diet This demand has attracted fraudulent attempts to market olive oil which has been adulterated with cheaper oils. This study focuses on the near infrared (NIR) spectroscopic determination of adulteration of olive oil by vegetable oils using multivariate calibration. The binary, ternary and quaternary mixtures of olive, soybean, cotton, corn, canola and sunflower oils were prepared using a random design. The absorbance spectra of these synthetic samples were measured by a near infrared (NIR) spectrometer. A genetic algorithm-based variable selection algorithm, coupled with an inverse least squares multivariate calibration method (GILS) was used to build calibration models for possible adulterants and olive oil in the adulterated mixtures The correlation coefficients of actual versus predicted concentrations resulting from multivariate calibration models for the different oils were between 0 90 and 0.99 The results demonstrated that NIR spectroscopy in conjunction with the GILS method makes it possible to determine the adulteration of olive oils regardless of adulterant vegetable oils over a wide range of concentrations.Article Citation - WoS: 25Citation - Scopus: 27Osteogenic Differentiation of Mesenchymal Stem Cells on Random and Aligned Pan/Ppy Nanofibrous Scaffolds(SAGE Publications, 2019) Selamet, Yusuf; İnce Yardımcı, Atike; Baskan, Öznur; Yılmaz, Selahattin; Meşe, Gülistan; Özçivici, EnginThe aim of this study was to develop random and aligned polyacrilonitrile (PAN)/polypyrrole (PPy) nanofibrous scaffolds by electrospinning technique for osteogenic differentiation of mesenchymal stem cells. Nanofibers were fabricated successfully as straight, smooth, and free from bead formation. The average diameter of random and aligned nanofibers was 268(+/- 49) nm and 225(+/- 72) nm, respectively. Alignment process increased the tensile strength of nanofibers 3.9-fold, while the tensile strain of nanofibers decreased by 78%. PAN/PPy nanofibers were hydrophilic with the contact angle value of about 32 degrees and alignment did not affect the contact angle value. Random and aligned PAN/PPy nanofibers were investigated as a scaffold material for osteogenic differentiation of D1 ORL UVA mouse bone marrow mesenchymal stem cells. Cells were able to attach and grow on nanofibers confirmed by cell viability results. Stem cells that were cultured with osteogenic induction were able to mineralize on electrospun nanofibers based on alizarin red and Von Kossa dye staining. For aligned PPy nanofibers, mineralization occurred in the fiber alignment direction. Consequently, PAN/PPy nanofibrous mats in both random and aligned forms would be potential candidates for bone tissue engineering.Article Citation - WoS: 40Citation - Scopus: 37Investigation of Interlayer Hybridization Effect on Burst Pressure Performance of Composite Overwrapped Pressure Vessels With Load-Sharing Metallic Liner(SAGE Publications, 2020) Kangal, Serkan; Kartav, Osman; Tanoğlu, Metin; Aktaş, Engin; Artem, Hatice SeçilIn this study, multi-layered composite overwrapped pressure vessels for high-pressure gaseous storage were designed, modeled by finite element method and manufactured by filament winding technique. 34CrMo4 steel was selected as a load-sharing metallic liner. Glass and carbon filaments were overwrapped on the liner with a winding angle of [+/- 11 degrees/90 degrees(2)](3) to obtain fully overwrapped composite reinforced vessel with non-identical front and back dome endings. The vessels were loaded with increasing internal pressure up to the burst pressure level. The mechanical performances of pressure vessels, (i) fully overwrapped with glass fibers and (ii) with additional two carbon hoop layers on the cylindrical section, were investigated by both experimental and numerical approaches. In numerical approaches, finite element analysis was performed featuring a simple progressive damage model available in ANSYS software package for the composite section. The metal liner was modeled as elastic-plastic material. The results reveal that the finite element model provides a good correlation between experimental and numerical strain results for the vessels, together with the indication of the positive effect on radial deformation of the COPVs due to the composite interlayer hybridization. The constructed model was also able to predict experimental burst pressures within a range of 8%. However, the experimental and finite element analysis results showed that hybridization of hoop layers did not have any significant impact on the burst pressure performance of the vessels. This finding was attributed to the change of load-sharing capacity of composite layers due to the stiffness difference of carbon and glass fibers.Article Citation - WoS: 8Citation - Scopus: 9Dynamic Behavior Predictions of Fiber-Metal Laminate/Aluminum Foam Sandwiches Under Various Explosive Weights(SAGE Publications, 2016) Baştürk, Suat Bahar; Tanoğlu, Metin; Çankaya, Mehmet Alper; Eğilmez, Oğuz ÖzgürApplication of blast tests causes some problems to characterize the performance of panels due to the drastic conditions of explosive medium. Real test has high safety concerns and is not easily accessible because of its extra budget. Some approaches are needed for the preliminary predictions of dynamic characteristics of panels under blast loading conditions. In this study, the response of sandwiches under blast effect was evaluated by combining quasi-static experiments and computational blast test data. The primary aim is to relate the quasi-static panel analysis to dynamic blast load. Based on this idea, lightweight sandwich composites were subjected to quasi-static compression loading with a special test apparatus and the samples were assumed as single degree-of-freedom mass-spring systems to include dynamic effect. This approach provides a simpler way to simulate the blast loading over the surface of the panels and reveals the possible failure mechanisms without applying any explosives. Therefore the design of the panels can be revised by considering quasi-static test results. In this work, the peak deflections and survivabilities of sandwiches for various explosive weights were predicted based on the formulations reported in the literature. Major failure types were also identified and evaluated with respect to their thicknesses.Article Citation - WoS: 7Citation - Scopus: 9Effects of Hybrid Yarn Preparation Technique and Fiber Sizing on the Mechanical Properties of Continuous Glass Fiber-Reinforced Polypropylene Composites(SAGE Publications, 2016) Merter, N. Emrah; Başer, Gülnur; Tanoğlu, MetinIn this study, hybrid yarns were developed by commingling the continuous polypropylene and glass fibers using air jet and direct twist preparation techniques. The non-crimp fabrics were obtained with +/- 45 degrees fiber orientation from these hybrid yarns. The fabrics were prepared with fiber sizings that are compatible and incompatible with polypropylene matrix to investigate the effect of interfacial adhesion on the properties of the thermoplastic composites. Composite panels were produced from the developed fabrics by hot press compression method and microstructural and mechanical properties of the composites were investigated. It was found that type of the hybrid yarn preparation technique and glass fiber sizing applied on the glass fibers have some important role on the properties of the composites. Composites made of fabrics produced by air jet hybrid yarn preparation technique exhibited better results than those produced by direct twist covering (single or double) hybrid yarn preparation techniques. The highest flexural properties (99.1MPa flexural strength and 9.55 GPa flexural modulus) were obtained from the composites manufactured from fabric containing compatible sizing, due to better adhesion at the interface of glass fibers and polypropylene matrix. The composite fabricated from fabric with polypropylene compatible sizing also exhibited the highest peel resistance (interlaminar peel strength value of 5.87N/mm). On the other hand, it was found that hybrid yarn preparation technique and type of the glass fiber sizing have insignificant effect on the impact properties of the glass fiber/polypropylene composites.Article Citation - WoS: 9Citation - Scopus: 10On the Estimation and Optimization Capabilities of the Fatigue Life Prediction Models in Composite Laminates(SAGE Publications, 2018) Deveci, Hamza Arda; Artem, Hatice SeçilIn this study, the estimation and optimization capabilities of the multiaxial fatigue life prediction models, namely, Failure Tensor Polynomial in Fatigue, Fawaz-Ellyin, Sims-Brogdon and Shokrieh-Taheri are investigated comparatively. Fatigue life predictions are obtained for multidirectional graphite/epoxy, glass/epoxy, carbon/epoxy and carbon/PEEK composite laminate data taken from the literature. The prediction study shows that the models can predict the fatigue behavior of the multidirectional laminates at different degrees of proximity. In the optimization, a hybrid algorithm combining particle swarm algorithm and generalized pattern search algorithm is used to search the optimum stacking sequence designs of the laminated composites for maximum fatigue life. The hybrid algorithm shows superior performance in terms of computational time and finding improved global optima compared to the best results presented in the literature. After the capability of the models and the reliability of the algorithm are revealed, several lay-up design problems involving different cyclic loading scenarios are solved. The results indicate that the reliability of the optimization may considerably change according to the used model even if the model may yield reasonable prediction results.