Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
3 results
Search Results
Article Citation - WoS: 22Citation - Scopus: 29Inter-Granular Cracking Through Strain Gradient Crystal Plasticity and Cohesive Zone Modeling Approaches(Elsevier, 2019) Yalçınkaya, Tuncay; Özdemir, İzzet; Fırat, Ali OsmanEven though intergranular fracture is generally regarded as a macroscopically brittle mechanism, there are various cases where the fracture occurs at the grain boundaries with considerable plastic deformation at the macroscopic scale. There exists several microstructural reasons for grain boundaries to host crack initiation. They can interact with impurities and defects, can provide preferential location for precipitation, can behave as a source of dislocations and can impede the movement of dislocations as well. The understanding of the crack initiation and propagation at the grain boundaries requires the analysis of the grain boundary orientation and the orientation mismatch between the neighboring grains and the related the stress concentration, which is only possible through the combination of micro-mechanical plasticity and fracture mechanics. For this reason the current work studies the evolution of plasticity in three dimensional Voronoi based microstructures through a strain gradient crystal plasticity framework (see e.g. Yalcinkaya et al., 2011; Yalcinkaya et al., 2012; Yalcinkaya, 2016) and incorporates a potential based cohesive zone model (see Park et al., 2009; Cerrone et al., 2014) at the grain boundaries for the crack initiation and propagation. The numerical examples considers the effect of the orientation distribution, the grain boundary conditions, the specimen size and the fracture energy parameter on the intergranular fracture behavior of micron-sized specimens. The study presents important conclusions for the modeling of fracture at this length scale.Article Citation - WoS: 18Citation - Scopus: 26Compressive Mechanical Behaviour of E-glass/Polyester Composite Laminates Tailored With a Thermoplastic Preforming Binder(Elsevier Ltd., 2003) Tanoğlu, Metin; Seyhan, Abdullah TuğrulCompressive mechanical behaviour and failure modes of E (electrical)-glass/polyester composite laminates tailored with a thermoplastic preforming polyester binder were investigated under ply-lay up and in-plane loading directions. Fiber preforms with various amount of the binder were consolidated under heat and pressure. The preform compaction experiments were performed by applying compressive pressure to the preforms, and the average thickness as a function of pressure was measured. It was found that the highest compaction of the preforms and therefore the highest fiber volume fraction can be obtained with 3 wt.% of the binder. Further increase of the amount of binder decreases the degree of compaction. Composite panels were fabricated by vacuum-assisted resin transfer molding using fabric preforms with various binder concentrations. The present investigation reveals that there are considerable effects of the binder on the compressive mechanical behaviour of the composites. Compression testing of the composites showed that the average strength values are in the range of 400-600 and 150-300 MPa for ply-lay up and in-plane directions, respectively. Also, both the strength and modulus values increase up to 3 wt.% of the binder, and these values decrease with further addition of the binder. Scanning electron microscopy showed that failure modes of the composites are altered significantly by the presence of the binder. Furthermore, the interaction between the binder and the reacting resin was followed to determine the extent of the binder dissolution and its effects on the viscosity of the resin and the mechanical behaviour of the matrix polymer. The results indicate that there is a partial dissolution of the binder within the matrix resin.Conference Object Citation - WoS: 7Citation - Scopus: 9An Elastic Hollow Cylinder Under Axial Tension Containing a Crack and Two Rigid Inclusions of Ring Shape(Elsevier Ltd., 2002) Artem, Hatice Seçil; Geçit, Mehmet RuşenThis paper is concerned with the fracture of an axisymmetric hollow cylindrical bar containing rigid inclusions. The cylinder is under the action of uniformly distributed axial tension applied at infinity. The bar contains a ring-shaped crack at the symmetry plane whose surfaces are free of tractions and two ring-shaped rigid inclusions with negligible thickness symmetrically located on both sides of the crack. It is assumed that the material of the cylinder is linearly elastic and isotropic. The mixed boundary conditions of the problem lead the analysis to a system of three singular integral equations for crack surface displacement derivative and normal and shearing stress jumps on rigid inclusions. These integral equations are solved numerically and the stress intensity factors are calculated.