Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection

Permanent URI for this collectionhttps://hdl.handle.net/11147/7148

Browse

Filters

1994 - 199912000 - 200912010 - 20181

Settings

Access Right: Open AccessSubject: search.filters.subject.Magnesium

Search Results

Now showing 1 - 3 of 3
  • Article
    Citation - WoS: 2
    Citation - Scopus: 2
    The Synthesis of Super-Hydrophilic and Hard Mgb2 Coatings as an Alternative To Electroless Nickel Coatings
    (Slovenska Akademia Vied, 2018) Bülbüll, Ferhat; Güney, M.; Jafarpour, Somaiyeh; 01. Izmir Institute of Technology
    In this study, we report the electroless deposition using an alternative technique for the fabrication of hard and super-hydrophilic MgB2 films. MgB2 films on AZ91 magnesium alloys were prepared using an electroless bath containing magnesium diboride nanopowders, sodium hypophosphite, sodium succinate, sodium acetate, and dimethyl sulfoxide. The electroless deposition was carried out in a bath kept at a bath temperature of 95 degrees C for 60 min. After deposition, the coated samples were annealed at 300 degrees C for 60 min to investigate crystallization, morphology, and the changes in the hardness and wettability. The phase composition, morphology, the hardness, and the contact angle of produced coatings were studied by X-ray diffractometer, scanning electron microscopy, microhardness tester, and contact angle measurement system, respectively. The coatings exhibited a dense and nodular structure with strong grain connections. As-deposited and annealed MgB2 films showed an orientation with the (101) reflection, and the highest hardness value (500 HV0.01) was obtained from the annealed coating. Both synthesized coatings had a super-hydrophilic surface.
  • Article
    Citation - WoS: 10
    Electrolysis of Mgcl2 With a Top Inserted Anode and an Mg-Pb Cathode
    (Springer Verlag, 1994) Güden, Mustafa; Güden, Mustafa; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of Technology
    High energy consumption in the production of magnesium by molten salt electrolysis is mainly due to the recombination of magnesium and chlorine. The large interelectrode distance used, in conventional techniques, to reduce the extent of ‘back reaction’, results in a significant potential drop. A laboratory cell that enables the operation with smaller interelectrode distance and easy separation of electrode products has been used to study electrolytic magnesium production. The cell features a top inserted graphite anode and a Mg-Pb alloy cathode at the bottom. Current efficiency and power consumption were determined at 690° C using a current density of 0.48 A cm−2. Experiments were performed to study the effects of MgCl2 concentration and anode-cathode distance (a.c.d.) on cell operation. Results indicated that an electrolyte containing 20% MgCl2 (equiweight NaCl:KCl and 1 % NaF) with a 3 cm a.c.d. reduced the cell voltage to 3.72 V. This value corresponds to an energy consumption of 11.3 kWh kg−1 including the refining of Mg-Pb alloy produced at the cathode. This cell performance is more energy efficient compared to conventional magnesium cells.
  • Article
    Citation - WoS: 19
    Citation - Scopus: 21
    Effect of Strain Rate on the Compressive Mechanical Behavior of a Continuous Alumina Fiber Reinforced Ze41a Magnesium Alloy Based Composite
    (Elsevier Ltd., 2006) Güden, Mustafa; Akil, Övünç; Güden, Mustafa; Çiftçioğlu, Muhsin; Hall, Ian W.; Taşdemirci, Alper; Çiftçioğlu, Muhsin; 03.02. Department of Chemical Engineering; 03.10. Department of Mechanical Engineering; 03. Faculty of Engineering; 01. Izmir Institute of Technology
    The compressive mechanical response of an FP™ continuous fiber (35 vol.%) Mg composite has been determined in the transverse and longitudinal directions at quasi-static and high strain rates. It was found that the composite in the transverse direction exhibited strain rate sensitivity of the flow stress and maximum stress within the studied strain-rate range of 1.3 × 10−4 to 1550 s−1. The failure strain in this direction, however, decreased with increasing strain rate. Microscopic observations on the failed samples have shown that the composite failed by shear banding along the diagonal axis, 45° to the loading axis. Twinning was observed in the deformed cross-sections of the samples particularly in and near the shear band region. The strain rate sensitivity of the fracture stress of the composite in transverse direction is attributed to the matrix strain rate sensitivity. In the longitudinal direction, the composite failed by kink formation at quasi-static strain rates, while kinking and splitting were observed at the high strain rates. The maximum stress in the longitudinal direction was, however, found to be strain rate insensitive within the strain rate regime of 1.3 × 10−4 to 500 s−1. In this direction, similar to transverse direction, twinning was observed in the highly deformed kink region. Several different reasons are proposed for the strain rate insensitive compressive strength in this direction.