Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
52 results
Search Results
Article Citation - WoS: 24Citation - Scopus: 23Photovoltaic Performance of Magnetron Sputtered Antimony Selenide Thin Film Solar Cells Buffered by Cadmium Sulfide and Cadmium Sulfide /Zinc Sulfide(Elsevier B.V., 2023) Cantas, A.; Gundogan, S.H.; Turkoglu, F.; Koseoglu, H.; Aygun, G.; Ozyuzer, L.Antimony selenide (Sb2Se3)-based thin-film solar cells have recently attracted worldwide attention as an abundant, low-cost, and efficient photovoltaic technology. The highest efficiencies recorded for Sb2Se3 solar cells have been obtained using cadmium sulfide (CdS) as a buffer layer. The Cd-included hybrid buffer layers could be one option to increase device efficiency through more effective usage of light. Therefore, in this work, the effect of single CdS and hybrid CdS/zinc sulfide (ZnS) buffer layers on the photovoltaic performance of Sb2Se3 thin-film solar cells has been investigated in detail. Sb2Se3 thin films have been deposited on molybdenum (Mo)-coated soda-lime glass (SLG) substrates by radio frequency magnetron sputtering technique followed by a post-heat treatment process. The morphological, and structural properties of Sb2Se3 thin films have been investigated by X-Ray Diffraction and Scanning Electron Microscopy. To compare the device performances of single CdS and hybrid CdS/ZnS buffered Sb2Se3 thin-film solar cells, SLG/Mo/Sb2Se3/CdS/ZnS/indium tin oxide (ITO) and SLG/Mo/Sb2Se3/CdS/ITO structures have been fabricated. The findings of this study have revealed a reduction in solar cells’ performance from η=3.93% for CdS buffer to η=0.13% for CdS/ZnS hybrid buffer. The change in the solar cell performance using the CdS/ZnS hybrid buffer has been discussed in detail. © 2023 Elsevier B.V.Article Citation - WoS: 10Citation - Scopus: 12Enhanced Model Protein Adsorption of Nanoparticulate Hydroxyapatite Thin Films on Silk Sericin and Fibroin Surfaces(Springer, 2022) Özcan, Selçuk; Çiftçioğlu, MuhsinHydroxyapatite coated metallic implants favorably combine the required biocompatibility with the mechanical properties. As an alternative to the industrial coating method of plasma spraying with inherently potential deleterious effects, sol-gel methods have attracted much attention. In this study, the effects of intermediate silk fibroin and silk sericin layers on the protein adsorption capacity of hydroxyapatite films formed by a particulate sol-gel method were determined experimentally. The preparation of the layered silk protein/hydroxyapatite structures on glass substrates, and the effects of the underlying silk proteins on the topography of the hydroxyapatite coatings were described. The topography of the hydroxyapatite layer fabricated on the silk sericin was such that the hydroxyapatite particles were oriented forming an oriented crystalline surface. The model protein (bovine serum albumin) adsorption increased to 2.62 µg/cm2 on the latter surface as compared to 1.37 µg/cm2 of hydroxyapatite on glass without an intermediate silk sericin layer. [Figure not available: see fulltext.].Article Citation - WoS: 28Citation - Scopus: 29Development of a High-Flux Thin-Film Composite Nanofiltration Membrane With Sub-Nanometer Selectivity Using a Ph and Temperature-Responsive Pentablock Co-Polymer(American Chemical Society, 2019) Bar, Canbike; Çağlar, Nagahan; Uz, Metin; Mallapragada, Surya K.; Alsoy Altınkaya, SacideProducing block co-polymer-based nanofiltration (NF) membranes with sharp molecular weight cutoffs via an efficient method exhibiting persistent size-based separation quality is challenging. In this study, this challenge was addressed by reporting a facile approach to fabricate pentablock co-polymer (PBC)-based thin-film composite (TFC) NF membranes. The PBC, consisting of temperature-responsive Pluronic F127 (PEO-b-PPO-b-PEO) middle blocks and pH-responsive poly(N,N-(diethylamino)ethyl methacrylate) end blocks, were synthesized by atom-transfer radical polymerization. This polymer was then attached electrostatically to the surface of polysulfone/sulfonated polyether-sulfone support membranes fabricated using a non-solvent-induced phase separation technique. The conformational changes of the PBC chains in response to pH and temperature determined the, pure water flux and neutral solute (PEG 1000) rejection performance of TFC membranes. Permeability of the membranes increased from 13.0 +/- 0.63 to 15.9 +/- 0.06 L/m(2).h bar and from 6.7 +/- 0.00 to 13.9 +/- 0.07 L/m(2).h.bar by changing the solution pH from 4 to 8.5 and temperature from 4 to 25 degrees C, respectively. The pH- and temperature-responsive conformational changes did not affect the PEG 1000 rejection and membrane pore radius, which remained constant at similar to 89% and similar to 0.9 nm, respectively. This important finding was attributed to the high grafting density of co-polymer chains, resulting in spatial limitations among the grafted chains. The pore size of similar to 0.9 nm achieved with the proposed membrane design is the smallest size reported so far for membranes fabricated from block copolymers. TFC membranes demonstrated high stability and maintained their flux and rejection values under both static (storage in an acidic solution for up to 1 month) and dynamic (filtering PEG 1000 solution over 1 week) conditions. Pentablock copolymers enable a NF membrane with a sharp molecular weight cutoff suitable for size-selective separations. The membrane fabrication technique proposed in this study is a scalable and promising alternative that does not involve complex synthetic routes.Article Citation - WoS: 6Citation - Scopus: 6Experimental and Density Functional Theory Study on Humidity Sensing Properties of Copper Phthalocyanine (cupc)(IOP Publishing, 2019) Farzaneh, Amir; Esrafili, Mehdi D.; Okur, SalihThe quartz crystal microbalance (QCM) technique was applied to investigate humidity sensing properties of a copper phthalocyanine (CuPc) thin film prepared by drop cast method. The humidity adsorption and desorption kinetics of (CuPc) thin film was evaluated. The QCM and electrical measurements results showed that humidity sensing properties of CuPc is very sensitive to humidity changes and reversible adsorption/desorption performance which is an indicative of a good humidity sensor even at room temperature. Reproducible experimental results indicated that CuPc thin films have an abundant potential for humidity sensing applications at ambient temperature. According to the first-principle density functional theory calculations, the promising humidity sensing properties of CuPc can be attributed to the considerable charge transfer from the water molecule into Cu atom.Article Citation - WoS: 50Citation - Scopus: 52Monitoring the Characteristic Properties of Ga-Doped Zno by Raman Spectroscopy and Atomic Scale Calculations(Elsevier, 2019) Horzum, Şeyda; İyikanat, Fadıl; Senger, Ramazan Tuğrul; Çelebi, Cem; Sbeta, Mohamed; Yıldız, Abdullah; Serin, TülayWe experimentally and theoretically study how the structural and vibrational properties of zinc oxide (ZnO) are modified upon Gallium (Ga) doping. The characteristics of Ga-doped ZnO thin films which are synthesized by sol-gel spin coating method on glass substrates are monitored by using X-ray diffraction (XRD) and Raman scattering measurements. For atomic-level understanding of the experimental findings state-of-the-art density functional theory (DFT) based calculations are also performed. DFT calculations reveal that both the substitution and adsorption of Ga atoms in ZnO are energetically possible and substitutional doping in ZnO is the most favourable scenario. XRD measurements show that all the films are in wurtzite structure and the crystallite size of the films decreases with increasing Ga doping. In addition, Raman analysis show that strong vibrational modes at about 100 and 441 cm(-1) are associated with E-2(low) and E-2(high) phonon branches of ZnO, respectively. While the frequency of the E-2(low) mode downshifts with increasing Ga concentration, the E-2(high) phonon mode is not affected by the Ga doping. Furthermore, E-Ga phonon branch, stemming from the substituted Ga atoms, emerges at low frequencies. It is also seen that the Raman intensity of the E-G(a) peak linearly increases with increasing Ga concentration. Experimental results on the vibrational properties are in good agreement with the ab initio phonon calculations. (C) 2018 Elsevier B.V. All rights reserved.Article Citation - WoS: 22Citation - Scopus: 27Mechanisms Behind Slow Photoresponse Character of Pulsed Electron Deposited Zno Thin Films(Elsevier, 2020) Özdoğan, Mehmet; Çelebi, Cem; Utlu, GökhanSemiconducting Zinc Oxide (ZnO) is ideal candidate for ultraviolet (UV) photodetector due to its promising optoelectronic properties. Photoconductive type ZnO photodetectors, which is fabricated in metal-semiconductor-metal configuration, show mostly very high photoconductivity under UV light, but they are plagued by slow photoresponse time as slow as several tens of hours, even more. Most of the studies claimed that atmospheric adsorbates such as water and oxygen create charge traps states on the surface and remarkably increase both the photoconductivity and response time. There are also limited studies, which claim that the defect states acting as hole trap centers prolong response time significantly. However, the underlying physical mechanism is still unclear. Here we study the effects of both adsorbates and defect-related states on the photoresponse character of Pulsed Electron Deposited ZnO thin films. In order to distinguish between these two mechanisms, we have compared the time-dependent photoresponse measurements of bare-ZnO and SiO2 encapsulated-ZnO thin film samples taken under UV light and high vacuum. We show that the dominant mechanism of photoresponse in ZnO is the adsorption/desorption of oxygen and water molecules even when the measurement is performed in high vacuum. After the encapsulation of sample surface by a thin SiO2 layer, the adsorption/desorption rates can significantly improve, and the effects of these molecules partially removed.Article Citation - WoS: 33Citation - Scopus: 33Characterization of Thin Film Li0.5la0.5ti1-Xalxo3 Electrolyte for All-Solid Li-Ion Batteries(Elsevier, 2018) Ulusoy, Seda; Gülen, Sena; Aygün, Gülnur; Özyüzer, Lütfi; Özdemir, MehtapSince addition of Al in Li0.5La0.5TiO3 has enhanced ionic conductivity in bulk materials, it is important to apply this material on all solid state thin film batteries. Because some of the good ionic conductors such as Lithium Phosphorus Oxynitride (LiPON) are sensitive to oxygen and moisture and their application is limited, so amorphous Li0.5La0.5Ti1−xAlxO3 (LLTAlO) is a most promising candidate because of its stability. In this study, the crystalline LLTAlO targets were prepared changing the amount of x content by conventional solid state reactions. Using these targets, lithium lanthanum titanium oxide (LLTO) thin film electrolytes were deposited on ITO/SLG substrates by radio frequency magnetron sputtering system in Ar atmosphere. The structural and compositional properties of targets and thin films were characterized by SEM, XRD, Raman spectroscopy and XPS. It was found that all targets are crystalline while the thin films are amorphous. To understand the effect of Al doping on ionic conductivity, electrical measurements were done at room temperature by AC impedance spectroscopy forming ITO/LLTAlO/Al structure like capacitor. Highest ionic conductivity result, 0.96 × 10−6 S·cm−1, is obtained from the nominal thin film composition of Li0.5La0.5Ti1−xAlxO3 (x = 0.05) at room temperature measurements. Heat treatment is also conducted to investigate to understand its effect on ionic conductivity and the structure of the thin films. It is found that ionic conductivity enhances with annealing. Also, temperature dependent ionic conductivity measurements from 298 K to 385 K are taken in order to evaluate activation energy for Li-ion conduction.Article Citation - WoS: 10Citation - Scopus: 12Transparent block copolymer thin films for protection of optical elements via chemical vapor deposition(Elsevier Ltd, 2018) Karabıyık, Merve; Ebil, ÖzgençIn this study, glycidyl methacrylate and 1H, 1H, 2H, 2H-perfluorodecyl acrylate copolymer p(GMA-co-PFDA) thin-films fabricated via Initiated Chemical Vapor Deposition (iCVD) were investigated as protective coatings on optical BK7 glass substrates and commercial optical filters. Durability tests based on military standards MIL-F-48616 and MIL-C-48497A were performed to evaluate performance of coatings for the protection of surfaces of optical elements. Cross-linked p(GMA-co-PFDA) copolymer coatings successfully passed all durability tests showing excellent mechanical properties and protection against humidity, salt water, swelling in water, and resistance to organic solvents while providing excellent adhesion to substrate. iCVD process enabled fine tuning of film morphology, mechanical properties and hydrophobicity by controlling the process parameters. Fabricated films were hydrophobic and highly transparent (>98%) in the wavelength range from 300 nm to 1000 nm. Optical transmittance measurements before and after coating process proved that while providing chemical and physical protection, p(GMA-co-PFDA) copolymer thin-films do not cause any detectable change in optical performance of commercial narrow band and wide band filters.Article Citation - WoS: 4Citation - Scopus: 5Identifying Threading Dislocations in Cdte Films by Reciprocal Space Mapping and Defect Decoration Etching(American Institute of Physics, 2018) Polat, Mustafa; Bilgilisoy, Elif; Arı, Ozan; Öztürk, Orhan; Selamet, YusufWe study threading dislocation (TD) density of high-quality cadmium telluride (CdTe) layers grown on a (211) oriented GaAs substrate by molecular beam epitaxy. High-resolution X-ray diffraction was performed to calculate the density of screw-type TDs by measuring the broadening of the asymmetrical (511) Bragg reflections of CdTe epilayers. In addition, total TD densities were determined by the Everson-etching method and were compared with screw TDs. Our results show that the total TD densities in CdTe films were dominated by those with screw character. The screw component TDs are estimated to account for more than 90% of the total TD density. CdTe layers grown at a thickness of less than 3.0 μm typically exhibit the screw TD densities in the 106 cm-2 and 107 cm-2 range. It can be noted that as the nucleation temperature increases, i.e., ≥222 °C, both the area density of TDs with the screw component of the CdTe films and the total TD density are roughly four times larger than those of the epilayer grown at the nucleation temperature of 215 °C. Furthermore, we discuss the influence of the II/VI flux ratio on the density of threading dislocations. The contribution of screw TDs to the total TD density showed a significant decrease in roughly 30% in the case of a high II/VI flux ratio. We further examine the reciprocal space maps in the vicinity of the (422) reflections.Article Citation - WoS: 6Citation - Scopus: 10Effect of Annealing on the Density of Defects in Epitaxial Cdte (211)/Gaas(Springer, 2018) Bakali, Emine; Selamet, Yusuf; Tarhan, EnverCdTe thin films were grown on GaAs (211) wafers by molecular beam epitaxy as the buffer layer for HgCdTe infrared detector applications. We studied the effect of annealing on the density of dislocation of these CdTe thin films under varying annealing parameters such as annealing temperature, annealing duration, and number of cycles. Annealings were carried out using a homemade annealing reactor possessing a special heater element made of a Si wafer for rapid heating. The density of dislocations, which were made observable with a scanning electron microscope after etching with an Everson solution, were calculated by counting the number of dislocations per unit surface area, hence the term etch pit density (EPD). We were able to decrease EPD values by one order of magnitude after annealing. For example, the best EPD value after a 20-min annealing at 400°C was ∼ 2 × 107 cm−2 for a 1.63-μm CdTe thin film which was about 9.5 × 107 cm−2 before annealing. We also employed Raman scattering measurements to see the changes in the structural quality of the samples. From the Raman measurements, we were able to see improvements in the quality of our samples from the annealing by studying the ratio of 2LO/LO phonon mode Raman intensities. We also observed a clear decrease in the intensity of Te precipitations-related modes, indicating a decrease in the size and number of these precipitations.