Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
2 results
Search Results
Article Citation - WoS: 2Citation - Scopus: 2A Comprehensive Study on the Effectiveness of the Stress and Damage Model Parameters in Predicting the Compression Fracture Behavior of Selective Laser Melted AlSi10Mg BCC Lattices(Elsevier B.V., 2025) Guden, Mustafa; Erten, Hacer Irem; Gorguluarslan, Recep M.; Gulletutan, Umut Can; Dagkolu, Akin; Gokdag, Istemihan; Namazov, SubhanThe Johnson and Cook (JC) stress and damage model parameters determined from the machined bulk cylindrical specimens and as-built struts through tension and compression tests were used to model quasi-static compression behavior of selective laser melt-fabricated AlSi10Mg alloy lattices. The lattices had the same cell size (10 mm) and strut diameter (1 mm), but different number of cells (2 x 2 x 2, 10 x 10 x 2 and 5 x 5 x 5) and geometries (sandwich and cubic). Four different sets of JC damage model parameters (brittle and ductile notch-insensitive and compression and tension notch-sensitive) were further implemented in the lattice compression numerical models. The brittle damage model parameters and smaller mesh sizes resulted in cracking the face-sheet corner strut nodes before the occurrence of a bending-dominated initial peak stress. The notch-sensitive damage model parameters exhibited no bent-strut fracture in the middle layers of the lattices and increased the crack initiation strains as compared with the notch-insensitive damage model parameters. Despite significant variations in the initial peak stresses of the tested 2 x 2 x 2 and 10 x 10 x 2 lattices, the implication of the strut micro-tension stress model together with the compression notch-sensitive damage model parameters using 0.25 mm mesh size conservatively approximated the experimental deformation stresses while the machined bulk specimen tensionstress model over predicted the experimental stresses. On the other side, the strut stress model with 0.15 mm mesh size accurately predicted the experimental diagonal shear/fracture mode of struts with a slightly higher numerical initial peak stress. The compression tests on the strut specimens extracted from the as-built lattices yielded similar stress model parameters with the micro-tension tests. The differences between the initial peak stresses of the investigated sandwich and cubic lattices were further explained by the differences in the lattice boundary conditions.Article Citation - WoS: 5Citation - Scopus: 5Mechanical Behaviour of Photopolymer Cell-Size Graded Triply Periodic Minimal Surface Structures at Different Deformation Rates(Mdpi, 2024) Yilmaz, Yunus Emre; Novak, Nejc; Al-Ketan, Oraib; Erten, Hacer Irem; Yaman, Ulas; Mauko, Anja; Ren, ZoranThis study investigates how varying cell size affects the mechanical behaviour of photopolymer Triply Periodic Minimal Surfaces (TPMS) under different deformation rates. Diamond, Gyroid, and Primitive TPMS structures with spatially graded cell sizes were tested. Quasi-static experiments measured boundary forces, representing material behaviour, inertia, and deformation mechanisms. Separate studies explored the base material's behaviour and its response to strain rate, revealing a strength increase with rising strain rate. Ten compression tests identified a critical strain rate of 0.7 s-1 for "Grey Pro" material, indicating a shift in failure susceptibility. X-ray tomography, camera recording, and image correlation techniques observed cell connectivity and non-uniform deformation in TPMS structures. Regions exceeding the critical rate fractured earlier. In Primitive structures, stiffness differences caused collapse after densification of smaller cells at lower rates. The study found increasing collapse initiation stress, plateau stress, densification strain, and specific energy absorption with higher deformation rates below the critical rate for all TPMS structures. However, cell-size graded Primitive structures showed a significant reduction in plateau and specific energy absorption at a 500 mm/min rate.