Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
38 results
Search Results
Article Deposition of (La,Sr)CoO₃-δ and (La,Sr)₂CoO₄-δ Cathode Layers on Gadolinia-Doped Ceria by Electrospray Deposition(Springer, 2025) Ergen, Emre; Akkurt, SedatLa-, Sr-, and Co-based oxides have proven their performances in the cathode layers of intermediate temperature levels of solid oxide fuel cells (SOFC), and hence have been frequently studied. They are deposited on the electrolyte layer by chemical vapor deposition (CVD), screen printing, pulsed laser deposition (PLD), etc. The electrospray deposition (ESD) proved itself as an effective and facile method for cathode deposition. Cathode layers deposited on gadolinia-doped ceria (GDC) with the compositions of (La0.5Sr0.5)CoO3, (La0.8Sr0.2)CoO3, (La0.5Sr0.5)2CoO4, and (La0.8Sr0.2)2CoO4 are known to provide low resistance values which are critical in cell performance. In this study, ESD is used for the first time as the coating method of these compositions. Area-specific resistance (ASR) measurements made by electrochemical impedance spectroscopy (EIS) showed promising results. Particularly, the sample coated in (La0.5Sr0.5)CoO3 composition showed an ASR value of 0.11 Omega.cm2 at 700 degrees C. ESD showed the ability to control the cathode coating microstructure by controlling the spraying parameters.Review Citation - WoS: 18Citation - Scopus: 18A Review on New Cobalt-Free Cathode Materials for Reversible Solid Oxide Fuel Cells(Chulalongkorn Univ, Metallurgy & Materials Science Research Inst, 2023) Akkurt, Sedat; Sındırac, Can; Özmen Egesoy, Tuğce; Ergen, EmreThe exponential growth in the requirement of fuel cells and batteries leads to increased demand for cobalt due to its common use in high-performance Li-ion batteries and high-temperature fuel cells/electrolyzers. This sharp increment in demand raises concern about the availability of limited reserves of cobalt which can impact the price of cobalt. Moreover, the geographic limitations of cobalt resources may endanger the whole supply chain. In addition to all those, huge moral issues of cobalt mining are also another problem. Hence, leading battery, fuel cells and electrolyzer manufacturers are looking for sustainable alternatives to reduce cobalt dependency. A more specific limitation is shown in Solid Oxide Fuel Cells (SOFCs) cathode materials that contain cobalt. Incompatibilities have already been observed between the cathode materials containing cobalt and the electrolytes in terms of the thermal expansion coefficient mismatch during the transition of the operating temperature from high to low. An advantage of low operating temperatures is the reduction of material costs compared to high temperature. Increasing the electrochemical performance of the cell and eliminating thermal expansion coefficient difference problems are in concert aimed at the development of cobalt-free cathode materials. Therefore, cobalt-free cathode materials are vital for the sustainability of SOFCs and green transition of the energy sector since they can be used as cathode and anode material in symmetrical SOFCs which is also known as reversible SOFC (RSOFC). In this review, we comprehensively summarize the recent advances of cobalt-free perovskite cathode materials for intermediate temperature RSOFCs.Article Citation - WoS: 2Citation - Scopus: 1Effects of Electrospraying Parameters on Deposition of La0.3sr0.7fe0.7cr0.3o3−δ Cathode Layer on Gdc(Wiley, 2022) Akkurt, Sedat; Sındıraç, Can; Özmen Egesoy, Tuğçe; Atıcı, Gökçe; Erişman, Elif; Erğen, Emre; Büyükaksoy, AligülHigh performance in intermediate temperature solid oxide fuel cells requires improvements especially in the microstructure of the cathode layer. New cobalt-free cathode materials are used because cobalt-containing cathodes have higher thermal expansion coefficients, poor long-term chemical stability, and lower mechanical stability. Recently cobalt-free cathodes have been proposed to solve these issues by using deposition methods other than electrospray deposition (ESD). In this study, ESD method is used to develop a cobalt-free cathode layer. The electrolyte layer is gadolinium-doped ceria that is deposited with La0.3Sr0.7Fe0.7 Cr0.3O3−δ (LSFCr) prepared by 2-butoxyethanol and ethylene glycol solvents as opposed to conventional solvents. Experimental ESD parameters are tested at different levels and combinations by applying statistical experimental design methods to optimize the microstructure. Coating deposited as such demonstrated higher electrochemical performance than similar electrodes fabricated by other methods.Article Citation - WoS: 2Citation - Scopus: 3A Full 3(4) Factorial Experimental Design for the Low Energy Building's External Wall(Vinca Inst Nuclear Sci, 2020) Pekdoğan, Tuğçe; Akkurt, Sedat; Başaran, TahsinThe low energy building concept is based on improving the building envelope to reduce heating and cooling loads. Improvements in building envelopes depend not only on climatic conditions but also on insulation. In this study, the thermal performance of external walls was studied by using a three-level full factorial statistical experimental design. An opaque wall in low energy buildings was chosen in order to study the effect of selected factors of city (A), orientation (B), insulation location (C), and month of the year (D) on heat loss or gain. A software was used to calculate the ANOVA table. As a result, all three factors of months of the year, city and orientation of the building facade were found to be significant factor effects for heat transfer. Two-factor interactions of AB, AD, BD, and CD were found to be significant. Therefore, the effects of season, location and orientation were successfully shown to be effective parameters.Article Citation - WoS: 54Citation - Scopus: 58Sintering and Microstructural Investigation of Gamma–alpha Alumina Powders(Elsevier Ltd., 2014) Yalamaç, Emre; Trapani, Antonio; Akkurt, SedatSintering behaviors of commercially available alumina powders were investigated using constant-heating rate dilatometric experiments. Each powder had different proportion of alpha/gamma alumina. Densification behaviors of powders were studied up to 1600 °C with three different heating rates of 1, 3.3 and 6.6 °C/min. Compacts of different gamma content alumina powders exhibited systematic anomalous second peaks in the densification rate curves at certain heating rates and temperatures. At 3.3 °C/min heating rate experiments, densification curves of 10% gamma phase alumina powder compacts reached a plateau after 1450 °C, and did not increase any further at higher temperatures. This phenomenon was double checked to understand powder behavior during sintering. 10% gamma phase alumina powder compacts showed the highest density for each heating rate. It reached 94% theoretical density with 1 °C/min heating rate. But 20% gamma phase alumina powder compacts had the finest grain size of about 1.40 ?m. Final density and porosity of compacts were also tested by image analysis and the results were coherent with Archimedes results. © 2014 Karabuk UniversityConference Object Citation - WoS: 3Citation - Scopus: 3Co-Sintering Behaviors of Oxide Based Bi-Materials(American Ceramic Society, 2010) Carry, Claude; Yalamaç, Emre; Akkurt, SedatBi-materials have attracted attention due to combination of properties that such structures can offer. A strong bond between two co-sintered oxide ceramics can provide novel properties. This study focused on the densification and the microstructural evolution during co-sintering of alumina (Al2O3)zirconia (Y-ZrO2) and alumina-spinel (MgAl2O4) bi-materials, produced by co-pressing of powders. High purity submicron powders were uniaxially pressed or co-pressed (150 or 250 MPa). The sintering behaviors of mono and bi-material bodies were investigated using a vertical dilatometer under constant heating rate conditions (from 1 to 10 degrees C/min up to 1580 degrees C). Microstructural characterizations focused on the interface and diffusion layers of bonded bi-materials. Best bonding without cracks were observed on alumina-spinel bi-materials. Macroscopic and microscopic observations are analyzed, interpreted and discussed considering shrinkage and thermal expansion mismatches, residual stresses, diffusion kinetics and oxide phase diagrams.Article Citation - WoS: 1Citation - Scopus: 1ANN model predicts floor tile properties(American Ceramic Society, 2004) Akkurt, Sedat; Özcan, Selçuk[No abstract available]Article Citation - WoS: 14Citation - Scopus: 15Electrochemical Performance of La0.6sr0.4co0.2fe0.8o3-Ce0.9gd0.1o2 Composite Sofc Cathodes Fabricated by Electrocatalyst And/Or Electrocatalyst-Ionic Conductor Infiltration(Springer, 2019) Sındıraç, Can; Büyükaksoy, Aligül; Akkurt, SedatInfiltration of electrocatalyst precursor solutions into previously sintered porous ionic conductor scaffolds has been used recently as an alternative method to the conventional co-sintering route to fabricate electrocatalyst-ionic conductor composites for solid oxide fuel cell (SOFC) cathode applications. However, the aqueous nitrate solutions generally used to perform the infiltration process results in electrocatalyst precipitates that are disconnected from each other, yielding poor electrode performance. In this work, polymeric electrocatalyst (La0.6Sr0.4Co0.2Fe0.8O3-LSCF) precursors that produce interconnected thin films upon heat treatment were used to infiltrate porous ionic conductor Ce0.9Gd0.1O2-delta (GDC) scaffolds to overcome these issues. In addition, for the first time in the literature, a mixture of LSCF and GDC polymeric precursors, which would yield LSCF-GDC nanocomposite coatings on the grains of the porous GDC scaffold were used as the infiltration solution. Thus, further enhancement of the electrocatalyst/ionic conductor interfacial area and achievement of improved electrode performance was aimed. As a result of the optimization studies, the lowest measured area specific polarization resistance (ASR(cathode)) values of 0.47 and 0.73 omega.cm(2) were obtained for polymeric LSCF+GDC and LSCF precursor infiltrations respectively at 700 degrees C, in air. In addition, LSCF+GDC infiltration yielded electrodes with much improved long-term stability in comparison to those obtained by LSCF infiltration. [GRAPHICS] .Article Citation - WoS: 25Citation - Scopus: 26Lowering the Sintering Temperature of Solid Oxide Fuel Cell Electrolytes by Infiltration(Elsevier Ltd., 2019) Sındıraç, Can; Çakırlar, Seda; Büyükaksoy, Aligül; Akkurt, SedatA dense electrolyte with a relative density of over 95% is vital to prevent gas leakage and thus the achievement of high open circuit voltage in solid oxide fuel cells (SOFCs). The densification process of ceria based electrolyte requires high temperatures heat treatment (i.e. 1400-1500 degrees C). Thus, the minimum co-sintering temperatures of the anode-electrode bilayers are fixed at these values, resulting in coarse anode microstructures and consequently poor performance. The main purpose of this study is to densify gadolinia doped ceria (GDC), a common SOFC electrolyte, at temperatures lower than 1400 degrees C. By this aim, an approach involving the infiltration of polymeric precursors into porous electrolyte scaffolds, a method commonly used for composite SOFC electrodes, is proposed. By infiltrating polymeric precursors of GDC into porous GDC scaffolds, a reduction in the sintering temperature by at least 200 degrees C is achieved with no additives that might affect the electrical properties. Energy dispersive x-ray spectroscopy line scan analyses performed on porous GDC scaffolds infiltrated by a marker solution (polymeric FeOx precursor in this case) reveals a homogeneous infiltrated phase distribution, demonstrating the effectiveness of polymeric precursors.Article Citation - WoS: 11Citation - Scopus: 12Electrical Properties of Gadolinia Doped Ceria Electrolytes Fabricated by Infiltration Aided Sintering(Elsevier Ltd., 2019) Sındıraç, Can; Büyükaksoy, Aligül; Akkurt, SedatCommon solid oxide fuel cell (SOFC) electrolyte materials (e.g., gadolinia doped ceria - GDC) demand temperatures exceeding 1400 degrees C for densification by conventional solid state sintering. It is very desirable to reduce the densification of the SOFC electroltytes to i) avoid microstructural coarsening of the composite anode layers, which are co-sintered with the electolyte layer in the anode supported SOFC fabrication scheme and ii) reduce energy consumption during SOFC manufacturing. We have recently demostrated a novel infiltration-aided sintering route to densify GDC ceramics at 1200 degrees C. In the present work, we present the electrical properties of GDC ceramics fabricated thusly. Comparison of high density (>= 95%) samples fabricated by conventional or infiltration-aided sintering reveal that at 700 degrees C, similar total electrical conductivities are obtained, while at 300 degrees C, specific grain boundary resistivity is smaller in the latter. Bulk (grain) conductivity is higher in porous GDC ceramics (relative density <= 90%) fabricated by infiltration-aided sintering than the conventionally sintered ones with similar porosities. Finally, open circuit voltage of 0.84 V at 700 degrees C, obtained under dilute hydrogen and stagnant air conditions suggests that GDC ceramics densified by infiltration-aided sintering are suitable for use as SOFC electrolytes.