Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
2 results
Search Results
Article Citation - WoS: 10Citation - Scopus: 10Determination of the Particle Interactions, Rheology and the Surface Roughness Relationship for Dental Restorative Ceramics(Elsevier Ltd., 2009) Kes, Mürşide; Polat, Hürriyet; Keleşoğlu, Serkan; Polat, Mehmet; Aksoy, GökhanThe effect of inter-particle interactions on the slurry properties and the final surface roughness of the dental ceramic restoratives was investigated. A commercial dental ceramic powder, IPS Empress 2 veneer, was used as the raw material. The magnitudes of the particle-particle interactions were computed by the DLVO theory for the ceramic slurries of different electrolyte solutions (0.1 M, 0.25 M, 0.5 M, 0.75 M, 1 M NaCl and CaCl2). As expected, the energies of particle-particle interactions were influenced significantly by the presence of electrolytes. These computations demonstrated that addition of electrolytes leads to a progressive depression of the repulsive double layer forces. The absence of these forces should inevitably lead to agglomeration caused by the ever-present van der Waals forces. The rheological measurements carried out using the slurries with same solution properties supported the findings of the DLVO computations. It was found that dental ceramic slurries showed a Newtonian behavior in the absence of electrolytes, which is indicative of little or no agglomeration in the slurry. On the other hand, the same slurries displayed a non-Newtonian, shear thinning behavior in the presence of electrolytes which can be attributed to agglomeration or gelation. Roughness of the ceramic surfaces produced from these slurries was studied by SEM analysis and profilometer measurements. Contact angle studies were also carried out on the same surfaces. It was observed that the surface became rougher initially with electrolyte addition to a maximum, most probably due to formation of isolated agglomerates due to a reduction of the repulsive double layer forces. After reaching a maximum, surface roughness decreased to a much lower value with further increase in electrolyte concentration. This was most probably caused by the formation of a relatively homogeneous, gel-like structure within the extensively agglomerated slurry due to a complete collapse of the double layer.Article Citation - WoS: 57Citation - Scopus: 62Effect of Various Treatment and Glazing (coating) Techniques on the Roughness and Wettability of Ceramic Dental Restorative Surfaces(Elsevier Ltd., 2006) Aksoy, Gökhan; Polat, Hürriyet; Polat, Mehmet; Çoşkun, G.Surface treatment procedures such as grinding and polishing are needed to provide the ceramic dental restorative materials with proper fitting and occlusion. The treated surfaces are customarily glazed to improve the strength and smoothness. Though smoothness and wetting of the dental surfaces are important to minimize bacterial plaque retention, influence of the surface treatment and glazing procedures on the final surface roughness and its correlation to wettability are overlooked. In this work, effect of various treatment (diamond fraising, stoning, sanding and aluminum oxide and rubber polishing) and glazing (auto and overglazing) techniques on the final roughness and the resulting wettability of dental ceramic surfaces were investigated using scanning electron microscopy (SEM) observations and atomic force microscopy (AFM) scans, 75 scans per sample. The surfaces were characterized and assigned an average roughness measure, Ra. The wettability of the same surfaces was evaluated using micro-contact angle measurements (25 micro-bubbles placed on a grid on each surface) to correlate the final surface roughness and wettability. The results show that overglazing prevails over surface irregularities from different treatment procedures and provides homegeneously smooth surfaces with mean Ra < 10 nm. It also produces uniformly wetted surfaces with low contact angles around 20°. The autoglazed surfaces are less smooth (mean Ra around 50 nm) and displays sporadic topographic irregularities. They display larger and less uniform contact angles ranging between 35° and 50°. The results suggest that overglazing should be preferred after surface treatment to obtain a smooth and well-wetted dental ceramic surface.