Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
41 results
Search Results
Article Citation - Scopus: 4One-step hydrothermal synthesis of spinel manganese oxide ion-sieve from commercial Γ-Mno2 and its uptake performance for lithium(Elsevier Ltd, 2024) Toprak, Seyra; Demir, Mustafa MuammerThe selective extraction of lithium from aqueous systems necessitates efficient sorbent materials. Spinel-type lithium manganese oxide ion sieves (LMOs) have been bee recognized for their high performance in this application. However, the elevated market cost of the spinel form (λ-MnO2) raises economic concerns, posing challenges to the feasibility of the extraction process. In this study, the one-step hydrothermal synthesis of Li1.33Mn1.67O4 was carried out at 200 °C for 7 days using commercial γ-MnO2 powder and aqueous LiOH solution as reactants. The synthesized powder exhibited characteristic XRD reflections consistent with spinel Li1.33Mn1.67O4. Lithium ion-sieve (H1.33Mn1.67O4) was obtained by leaching the LMO product with dilute hydrochloric acid solution. The sorption capacity of γ-MnO2 is increased from 8.4 to 23.1 mg/g (C0=200 mg/L), this capacity is very close to the one of the commercial λ-MnO2. The synthesized spinel HMO sorbent achieved a maximum Langmuir adsorption capacity of 52.1 mg/g. The extraction efficiency reached 94% at the sorbent dose of 20 g/L. The distribution coefficients of metal ions were in the order Li+ > Ca2+ > K+ > Na+, emphasizing selective Li+ extraction from brines with high Na+ content. These findings highlight the successful development of a spinel-type lithium manganese oxide ion sieve from γ-MnO2 polymorph, which is nearly an order of magnitude cheaper than the selective λ-MnO2. The study addresses critical issue of economic feasibility in lithium extraction processes, providing a potential solution for the selective recovery of bulk lithium. © 2024 Elsevier LtdArticle Citation - Scopus: 6Lithium Extraction From Geothermal Brine Using Γ-Mno2: a Case Study for Tuzla Geothermal Power Plant(Elsevier Ltd, 2024) Toprak, S.; Yılmaz, Selahattin; Öncel, Ç.; Baba, Alper; Yılmaz, S.; Demir, Mustafa Muammer; Baba, A.; Koç, G.A.; Demir, M.M.Geothermal brines contain high concentrations of ions and form a source of various valuable elements. The isolation of the elements from their water systems is a great challenge when the gradual depletion of ores in mining is considered. Attempts have been made for a long time to isolate valuable elements from aqueous mixtures prepared in the laboratory. However, those studies might not reflect the complexity of natural systems and might yield results that deviate significantly from the performance in real field systems. In this study, sorption is used to extract lithium ions from a representative field, Tuzla Geothermal Power Plant (TGPP) Turkey, using a mini-pilot reactor introduced to the reinjection well of the plant. Electrolytic manganese dioxide (γ-MnO2), a relatively inexpensive material widely used as the cathode material in lithium-ion batteries, was employed as a sorbent material for lithium. The sorption/desorption performance of the novel γ-MnO2 was investigated under various conditions. Sorption is performed at 360K and 2 bars. The maximum sorption performance was obtained at 1 h in Tuzla GPP. The desorption experiments were performed in acidic solutions. The concentration of Li+ in the desorption solution was found to be 25 mg/L on average when 10 g of γ-MnO2 was dispersed into 30 mL of the acidic aqueous solution. The first desorption solution was used consecutively for collecting more Li+ ions through the desorption of fresh brine-treated powder samples (cumulative desorption). By repeating this process four times consecutively, 230 mg/L of Li+ was obtained in the desorption solution. Moreover, the reusability of the γ-MnO2 sorbent was examined. The sorbent powder showed almost 40% performance efficiency compared to virgin powder under the conditions employed in this study. The use of electrolytic γ-MnO2 sorbent for lithium adsorption was found to be a promising process for practical use in the separation of lithium from geothermal brines. © 2024Article Citation - WoS: 4Citation - Scopus: 4Effects of Alkaline Earth Metal Additives on Methylammonium-Free Lead Halide Perovskite Thin Films and Solar Cells(Wiley, 2022) Yüce, Hürriyet; LaFollette, Diana K.; Demir, Mustafa Muammer; Perini, Carlo A.R.; Correa-Baena, Juan-PabloOrganic–inorganic lead halide perovskite solar cells are regarded as one of the most promising technologies for the next generation of photovoltaics due to their high power conversion efficiency (PCE) and simple solution manufacturing. Among the different compositions, the formamidinium lead iodide (FAPbI3) photoactive phase has a bandgap of 1.4 eV, which enables the corresponding higher PCEs according to the Shockley–Queisser limit. However, the photoactive crystal phase of FAPbI3 is not stable at room temperature. The most high-performing compositions to date have reduced this problem by incorporating the methylammonium (MA) cation into the FAPbI3 composition, although MA has poor stability at high temperatures and in humid environments, which can limit the lifetime of FAxMA1−xPbI3 films. CsxFA1−xPbI3 perovskites are also explored, but despite better stability they still lag in performance. Herein, the additive engineering of MA-free organic−inorganic lead halide perovskites using divalent cations Sr2+ and Ca2+to enhance the performances of CsxFA1−xPbI3 perovskite compositions is explored. It is revealed that the addition of up to 0.5% of Sr2+ and Ca2+ leads to improvements in morphology and reduction in microstrain. The structural improvements observed correlate with improved solar cell performances at low additive concentrations.Article Citation - WoS: 3Citation - Scopus: 6Hybrid Photonic-Plasmonic Mode-Coupling Induced Enhancement of the Spontaneous Emission Rate of Cds/Cdse Quantum Emitters(Elsevier, 2022) Gökbulut, Belkıs; İnanç, Arda; Topçu, Gökhan; Özçelik, Serdar; Demir, Mustafa Muammern this paper, a hybrid photonic-plasmonic resonator, which comprises an electrospun polymer fiber with a micrometer diameter and a core/shell nanostructure with a gold nanoparticle core, is constructed to investigate the dynamics of the coupled spontaneous emission of CdS/CdSe quantum dots (QDs). The gold nanoparticle core; covered with a silica shell, anchored with individual CdS/CdSe QDs, is placed inside a hollow cylindrical nanocavity formed on the surface of the microfiber to enable integration of the optical mode with the plasmonic effect, which is induced by the localized surface plasmons of the metal nanoparticle being present in the vicinity of the dipoles. The spontaneous emission rate of the QDs, coupled into the hybrid photonic-plasmonic mode, is measured to enhance by a factor of 23 via a time-resolved experimental technique. This result suggests that the regeneration of the optical mode-field inside the photonic-plasmonic resonator through the interaction of the dipoles with the localized surface plasmons of a metal nanoparticle strongly enhances the density of the electromagnetic states of the quantum emitters to facilitate an enhanced spontaneous emission within the host medium of the proposed polymer based-photonic structure.Article Citation - WoS: 7Citation - Scopus: 9Experimental Apparatus for Simultaneous Measurement of Triboelectricity and Triboluminescence(Elsevier Ltd., 2020) Arıca, Tuğçe A.; Topçu, Gökhan; Pala, Atamert; Demir, Mustafa MuammerTriboelectricity is a phenomenon caused by the accumulation of opposite electric charges on the surfaces of two different materials as a result of contact with each other. The phenomenon of emitting cold light when the material is subjected to physical deformation is called triboluminescence. This paper presents an experimental apparatus that allows simultaneous measurement of both triboelectricity and triboluminescence of a model composite system based on poly (vinylidene fluoride) (PVDF) and europium tetrakis (dibenzoylmethide) triethylammonium (EuD(4)TEA). While the former component was studied in contact-separation mode giving triboelectricity, the latter emits triboluminescence upon application of mechanical impact. The device was operated at varying range of frequencies from 0.5 to 4.8 Hz and the force in the range of 5.4-9.5 N. (C) 2019 Elsevier Ltd. All rights reserved.Article Citation - WoS: 36Citation - Scopus: 39Recent Developments of Colorimetric Mechanical Sensors Based on Polymer Composites(Royal Society of Chemistry, 2020) İnci, Ezgi; Topçu, Gökhan; Güner, Tuğrul; Demirkurt, Merve; Demir, Mustafa MuammerColorimetric mechanical (force, pressure, strain, and impact) sensors allow naked-eye visualization of existing structural deformations of a system occurring upon application of a mechanical action. The combination of mechanochromic materials with polymers offers a practical approach to designing and fabricating these sensors. Polymers as matrices can tolerate a wide range of forces and permits reusability of the sensors. On the other hand, mechanochromic materials provide unique colour properties depending on the type of mechanical action. They have also been frequently employed for the quantification of mechanical forces. As an example, non-centrosymmetric crystals are combined with polymers for sensing impact forces. Structures with photoluminescence and scattering and plasmonic resonances can be used to fabricate strain and pressure responsive composite materials, respectively. This study reviews recent advances in colorimetric mechanical sensor systems prepared using polymers and inorganic and organic mechanochromic materials working under a wide range of forces.Article Citation - WoS: 50Citation - Scopus: 58Chemically Modified Optical Fibers in Advanced Technology: an Overview(Elsevier, 2019) Shukla, S. K.; Kushwaha, Chandra Shekhar; Güner, Tuğrul; Demir, Mustafa MuammerIn recent years, chemically modified optical fibers have widely used for development of several advanced chemical and biosensors, biomedical technology and environmental monitoring. The chemically modified optical fiber bears several valuable properties like energy loss, catalytic behaviour, refractive index, and mechanical strength to advance the optical fiber technology. In this article, we reviewed the chemically-modified optical fiber and their applications in different optical fiber-based technologies. The basics of optical fiber and their modification are discussed along with the adopted methodologies. The advancements in different optical fiber based technologies viz sensing, imaging, tomography, magnetic resonance imaging, photodynamic therapy, optogenics, surgery and environmental monitoring are discussed in the light of the contribution of chemically modified optical fibers. In conclusion, success and challenges for the use of chemically modified-optical fiber are presented on the basis of existing literature.Article Citation - WoS: 4Citation - Scopus: 4Color-Tunable All-Inorganic Cspbbr3 Perovskites Nanoplatelet Films for Photovoltaic Devices(American Chemical Society, 2019) Özcan, Mehmet; Özen, Sercan; Topçu, Gökhan; Demir, Mustafa Muammer; Şahin, HasanHerein, we demonstrate a novel coating approach to fabricate CsPbBr3 perovskite nanoplatelet film with heat-free process via electrospraying from precursor solution. A detailed study is carried out to determine the effect of various parameters such as ligand concentration, electric field, flow rate, etc. on the optical properties. By controlling the volume ratios of the oleylamine (OAm) and oleic acid (OA), the coalescing and thickness of the resulting nanoplatelets can be readily tuned that results in control over emission in the range of 100 nm without any antisolvent crystallization or heating processes. The varying electrical field and flow rate was found as inefficient on the emission characteristics of the films. In addition, the crystal films were obtained under ambient conditions on the ITO coated glass surfaces as in the desired pattern. As a result, we demonstrated a facile and reproducible way of synthesizing and coating of CsPbBr3 perovskite nanoplatelets which is suitable for large-scale production. In this method, the ability of tuning the degree of quantum confinement for perovskite nanoplatelets is promising approach for the one-step fabrication of crystal films that may enable the use in optoelectronics.Article Citation - WoS: 25Citation - Scopus: 28Colorimetric and Plasmonic Pressure Sensors Based on Polyacrylamide/Au Nanoparticles(Elsevier, 2019) Topçu, Gökhan; Güner, Tuğrul; İnci, Ezgi; Demir, Mustafa MuammerColorimetric stimuli-responsive nanomaterials have emerged as an eminent tool for sensor applications. Among this class of sensing elements, gold nanoparticle-based (Au NP) nanostructures are promising materials due to their plasmonic features. In this study, free-standing flexible polymeric films having intense optical response upon application of mechanical pressure were fabricated based on polyacrylamide (PAAm) and Au NPs. Pressure may cause plasmonic shift most probably due to the disassembly of the clusters from blue to reddish individual particles depending on the extent of pressure. Temperature, time, and extent of pressure were examined in terms of spectral change of Au particles. The sensor films depict working range up to 160 MPa, which shows minor change at elevated temperatures probably due to the stress induced crystallization of PAAm. For practical applications, a simple red-green-blue (RGB) space-based algorithm was presented for smartphone-assisted detection of applied pressure. Moreover, the PAAm/Au composite structure shows self-healing without any additive under ambient conditions even after divided into pieces. (C) 2019 Elsevier B.V. All rights reserved.Article Citation - WoS: 4Citation - Scopus: 4Triboluminescent Composite Microspheres Consisting of Alginate and Eud(4)tea Crystals(Elsevier, 2018) İncel, Anıl; Demir, Mustafa MuammerAlginate is utilized to obtain luminescent composite microspheres containing europium tetrakis (dibenzoylmethide) triethylammonium (EuD4TEA) triboluminescent (TL) crystals. Na alginate is initially treated with Ca(II) and then Eu (III) so that physically-crosslinked alginate microspheres were obtained. EuD4TEA crystals are precipitated in situ on the surface of the spheres upon treatment with dibenzoylmethane (DBM) and triethylamine (TEA). The EuD4TEA/alginate composite spheres are swollen in aqueous system, the diameter of the microspheres increases from 180 up to 405 pm in 48 h. TL intensity of the spheres swollen in 1 h decreases 4 folds compared to dry spheres; however, it systematically increases as the swelling time is extended step-wise to 48 h. Swelling may develop structural homogenity in the microsphere that supresses the optical scattering and may lead to better transmittance of the TL signal. (C) 2017 Elsevier B.V. All rights reserved.