Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
12 results
Search Results
Conference Object Asymmetry in the Tension and Compression Flow Stress and the Effect of Sub-Cell Size on the Hardness of a Selective Laser Melt 316l Stainless Steel(Springer, 2022) Güden, Mustafa; Enser, Samed; Arslan Hamat, Burcu; Tanrıkulu, A. Alptuğ; Yavaş, HakanAn asymmetry between tension and compression tests was determined experimentally in the Selective Laser Melt (SLM) stainless steel 316L alloy in the building direction. The asymmetry was ascribed to the used biaxial scanning strategy which resulted in a strong alignment of 〈110〉 along the build direction (fiber texture) and a random distribution of 〈100〉, 〈110〉 and 〈111〉 directions normal to the building direction. The strong fiber texture in the building direction induced lower twinning stress in tension than in compression, while the tension and compression twining stresses were found similar in the normal to building direction. The favored twinning in the specimens tested in the building direction resulted in a higher tensile true fracture strain; hence, a higher ductility. Lastly, the hardness measurements made on the specimens having similar gain sizes, but different sub-cell sizes processed using higher and lower laser powers tended to support that the sub-cell boundaries in SLM-316L alloy acted as imperfect barriers to the dislocation motion.Conference Object The Shape and Size Effect of the Diatom Frustule Addition on the Compression Behavior of an Epoxy(Trans Tech Publications, 2018) Zeren, Doğuş; Kesici, Kutsal; Sukatar, Atakan; Güden, MustafaThe effects of the Achnanthes Taeniata and the diatomaceous earth (diatomite) frustules addition on the compressive strength of an epoxy matrix were investigated experimentally. The Achnanthes Taeniata frustules having relatively high length/diameter aspect ratio (2-4) were isolated and cultured in laboratory. While the as-received commercial natural diatomite frustules were non-homogenous in shape and size. The filling epoxy matrix with ~6 wt% of commercial natural diatomite increased the compressive strength from 60 MPa to 67 MPa, while the Achnanthes Taeniata frustules addition increased to 79 MPa. The increased compressive strength and modulus of the the Achnanthes Taeniata frustules filled epoxy was attributed to the higher aspect ratio and relatively strong bonding with the epoxy matrix. The more effective load transfer from the matrix to the Achnanthes Taeniata frustules associated with the enhanced interface bonding was also proved microscopically. The frustules were observed to pull-out on the fracture surface of the Achnanthes Taeniata frustules filled epoxy.Conference Object Citation - WoS: 1Citation - Scopus: 1Numerical and Experimental Studies of High Strain Rate Mechanical Behavior of E-glass/Polyester Composite Laminates(The American Society of Mechanical Engineers(ASME), 2010) Tunusoğlu, Gözde; Taşdemirci, Alper; Güden, Mustafa; Hall, Ian W.Quasi-static ∼10-3 s-1) and high strain rate (∼850 s-1) compression behavior of an E-glass/polyester composite was determined in the through-thickness and in-plane directions. In both directions, modulus and failure strength increased with increasing strain rate. Higher strain rate sensitivity for both elastic modulus and failure strength was observed in the in-plane direction. A numerical model was developed to investigate the compressive deformation and fracture of an E-glass/polyester composite. Excellent agreement was demonstrated for the case of high strain rate loading. Also, the fracture geometries were successfully predicted with the numerical model.Conference Object Citation - WoS: 3Citation - Scopus: 3Numerical Approach To Design Process of Armored Vehicles(The American Society of Mechanical Engineers(ASME), 2010) Erdik, Atıl; Kılıç, Namık; Güden, Mustafa; Taşdemirci, AlperToday, it is imperative that armored vehicles need advanced protection kits against anti-symmetric threats more than before. The primary goal of this study was to assess benefits of explicit hydrocodes for mine protection resistance of armored vehicles. An analysis of an armored vehicle under blast loading caused by high explosive (HE) detonation is presented with comparison to a full-scale test. The problem was examined using LS-DYNA which is an explicit non-linear finite element code. Multi Material Arbitrary Lagrangian Eulerian (MM-ALE) Fluid Structure Interaction Method was selected to model the explosion domain so as to observe advancing of the shock wave in the compressed air and to investigate the effects of blast on the vehicle structure after explosion. Johnson-Cook constitutive material model, Jones-Wilkins-Lee (JWL) and Linear Polynomial equation of states were used for the problem. Results show that numerical analysis was in good agreement with the experimental result.Conference Object Citation - WoS: 8Citation - Scopus: 12Mechanical Properties of Hydroxyapatite Composites Reinforced With Hydroxyapatite Whiskers(Trans Tech Publications, 2004) Şimşek, Deniz; Çiftçioğlu, Rukiye; Güden, Mustafa; Çiftçioğlu, Muhsin; Harsa, Hayriye ŞebnemSintering and mechanical behavior of pure and hydroxyapatite (HA) whisker reinforced HA composites were investigated in this work. Pure and composite samples were prepared by using a commercial powder and whiskers prepared by molten salt synthesis. The dry-pressed samples were sintered in the 800 and 1300°C range. The effect of whisker-addition on the mechanical properties of HA was investigated through compression and hardness testing. Compressive strength and fracture strain were observed to increase by the addition of whiskers.Article Citation - WoS: 24Citation - Scopus: 26Split Hopkinson Pressure Bar Compression Testing of an Aluminum Alloy: Effect of Lubricant Type(Chapman & Hall, 2003) Hall, Ian W.; Güden, MustafaThe Split Hopkinson Pressure Bar (SHPB), or Kolsky Bar, is widely used for studying the dynamic mechanical properties of metals and other materials. A cylindrical specimen is sandwiched between the incident and transmitter bars, Fig. 1, and a constant amplitude elastic wave is generated by the striker bar. Strain gages mounted on the incident and transmitter bars allow the compressive stress-strain response of the specimen to be established using uniaxial elastic wave theory [1]. A more detailed overview of SHPB testing is found in [2]. Lubricant is usually applied to the interfaces because the presence of any frictional effect on the specimen surfaces forms a multiaxial stress-state and invalidates one of the most important assumptions of the SHPB analysis, namely, a uniaxial stress state. This paper quantifies the effect for an aluminum alloy.Article Citation - Scopus: 31Quasi-Static Axial Crushing Behavior of Honeycomb-Filled Thin-Walled Aluminum Tubes(Bentham Science Publishers B.V., 2011) Aktay, Levent; Çakıroğlu, Cem; Güden, MustafaThe experimental and numerical quasi-static crushing behaviors of Nomex™ honeycomb-filled thin-walled Al tubes were investigated. The honeycomb filler was modeled using a unit cell model. The numerical model and experimental results have shown that, 6.4 mm and 4.8 mm cell size honeycomb filling had no effect on the deformation mode (diamond); however 3.2 mm cell size honeycomb filling changed the deformation mode to mixed/concertina. Honeycomb filling was also shown to increase the specific energy absorption of filled tubes over that of Al tube. The specific energy absorption of honeycomb filling was further compared with those of tube wall thickening and Al closedcell foam filling.Conference Object Citation - WoS: 5Citation - Scopus: 5Preparation and Microstuructural Development of Nanocrystalline Titania and Alumina(Trans Tech Publications, 2004) Çağlar Duvarcı, Özlem; Çiftçioğlu, Muhsin; Güden, Mustafa; Arıkut, G.The preparation of nanocrystalline titania and alumina was investigated by sol-gel methods using titanium isopropoxide, boehmite and aluminum isopropoxide. Various drying control chemical additives like oxalic acid, acetic acid and polyacrylic acid were used for modifying the drying behaviour and shrinkage of the gels. The sintered densities of the ceramics prepared by sol-gel processing and the dried gels were in the 79-99% of theoretical density for rutile. The green and sintered densities of the pellets prepared by uniaxial pressing of powders derived from sols, gels and precipitation techniques for titania were in the 40-52% and 55-83% respectively. The titania ceramics were observed to experience anatase-rutile phase transformation upon heat treatment at 650oC. The grain size of the sintered ceramics at 650oC was determined to be about 26 nm. Grain size of titania increased to 213 nm. at 850oC. The mechanical properties of these nanocrystalline ceramics were investigated by using microhardness testing.Book Part Citation - WoS: 21Citation - Scopus: 24Metals Foams for Biomedical Applications: Processing and Mechanical Properties(Springer, 2004) Güden, Mustafa; Çelik, Emrah; Çetiner, Sinan; Aydın, AlptekinOptimized structures found in nature can be sometimes imitated in engineering structures. The recent interest in functionally graded metallic materials makes bone structures interesting because bones are naturally functionally graded1. The cellular structure of foam metals (Fig.1) is very similar to that of the cancellous bone; therefore, these metals can be considered as potential candidates for future implant applications if porosity level, size and shape, strength and biocompatibility aspects satisfy the design specifications of implants. Foam metals based on biocompatible metallic materials (e.g. Ti and Ti-6A1-4V) are expected to provide better interaction with bone. This is mainly due to higher degree of bone growth into porous surfaces and higher degree of body fluid transport through three-dimensional interconnected array of pores2 (open cell foam), leading to better interlocking between implant and bone and hence reducing or avoiding the well-known implant losening. Furthermore, the elastic modulus of foam metals can be easily tailored with porosity level to match that of natural bone, leading to a better performance by avoiding the high degree of elastic mismatch which currently exists between conventional solid metallic implants and bone.Article Citation - WoS: 5Citation - Scopus: 7High Strain Rate Testing of a Unidirectionally Reinforced Graphite Epoxy Composite(Chapman & Hall, 2001) Hall, Ian W.; Güden, MustafaSince accurate, reproducible methods of testing polymer composites are not very well developed or standardized, this research forms part of a program to gain a better understanding of the mechanical properties and failure mechanisms of polymer composites at high strain rates. Since failure modes differ markedly depending on fiber architecture, orientation, fiber/matrix combination and so forth, these initial tests were carried out using a simple unidirectionally reinforced composite. Beginning with testing in the longitudinal and transverse directions, reported here, future experiments are being carried out to determine how the high strain rate properties vary with angle of testing, and then move on to other simple fiber lay-ups, ±90◦, ±45◦, etc.