Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
5 results
Search Results
Article Citation - WoS: 41Citation - Scopus: 45High Temperature Tensile, Compression and Creep Behavior of Recycled Short Carbon Fibre Reinforced Az91 Magnesium Alloy Fabricated by a High Shearing Dispersion Technique(National Engineering Research Center for Magnesium Alloys of China, Chongqing University, 2021) Kandemir, Sinan; Gavras, Sarkis; Dieringa, HajoThe present study seeks the feasibility of using short carbon fibres recycled from polymer matrix composites as alternative to virgin carbon fibres in the reinforcement of magnesium alloys. The microstructures, high temperature mechanical and creep properties of AZ91 alloy and its composites with various recycled carbon fibre contents (2.5 and 5 wt.%) and lengths (100 and 500 ?m) were investigated in the temperature range of 25–200 °C. The microstructural characterization showed that the high shear dispersion technique provided the cast composites with finer grains and relatively homogenous distribution of fibres. The materials tested displayed different behaviour depending on the type of loading. In general, while enhancements in the mechanical properties of composites is attributed to the load bearing and grain refinement effects of fibres, the fluctuations in the properties were discussed on the basis of porosity formation, relatively high reinforcement content leading to fibre clustering and interlayer found between the matrix and reinforcement compared to those of AZ91 alloy. The compressive creep tests revealed similar or higher minimum creep rates in the recycled carbon fibre reinforced AZ91 in comparison to the unreinforced AZ91. © 2021Article Citation - WoS: 16Citation - Scopus: 17Investigation of the High Temperature Dry Sliding Wear Behavior of Graphene Nanoplatelets Reinforced Aluminum Matrix Composites(SAGE Publications, 2021) Martin, Seçkin; Kandemir, Sinan; Antonov, M.In this study, graphene nanoplatelets (GNPs) with a thickness of 50-100 nm have been utilized to improve the mechanical and tribological properties of A360 alloy due to their extraordinary mechanical properties and solid lubricant nature. For the investigation of tribological properties, ball-on disc tests were carried out at various temperatures including room temperature (RT), 150 °C, and 300 °C. According to the hardness and ball-on-disc test results, the nanocomposite samples reinforced with GNPs exhibited improved hardness and wear resistance. The improvement in the wear behavior of nanocomposites was referred to the temporarily formed solid lubricant film of harder GNPs during the wear, and hence coefficient of friction (COF) and volume loss were considerably reduced. Abrasive-adhesive, oxidative, and mild-to-severe were found to be main wear mechanisms at RT, 150 °C, and 300 °C, respectively. Overall, the results show that the nanocomposites fabricated by casting method combined with mechanical stirring and ultrasonication have promising wear performance, especially at elevated temperatures. This may suggest that these developed materials could be potential candidates to be used in the engineering applications requiring high temperature wear performance. © The Author(s) 2020.Article Citation - WoS: 4Citation - Scopus: 5Effects of Tib2 Nanoparticle Content on the Microstructure and Mechanical Properties of Aluminum Matrix Nanocomposites(Walter de Gruyter GmbH, 2017) Kandemir, SinanThe present work reports the fabrication of A357 alloy matrix nanocomposites reinforced with 0.5, 1.0 and 2.0 wt.-% TiB2 nanoparticles (20-30 nm) by a novel method which is the combination of semi-solid mechanical mixing and ultrasonic dispersion of nanoparticles in liquid state. The microstructural and mechanical properties of the fabricated nanocomposites were investigated. The microstructural studies conducted with optical and advanced electron microscopes indicated that reasonably effective deagglomeration and uniform distribution of TiB2 nanoparticles into the matrix were achieved. Transmission electron microscopy studies also confirmed that the nanoparticles were embedded into the matrix and a good bonding was obtained between the matrix and the reinforcement. Increasing nanoparticle content led to grain refinement and significant enhancement in the mechanical properties of nanocomposites. The addition of 0.5, 1.0, and 2.0 wt.-% TiB2 nanoparticles increased the 0.2 % proof stress of matrix alloy by approximately 31, 48 and 61 %, respectively. The contribution of different mechanisms to the strength enhancement is discussed. It is proposed that the strengthening is mainly due to Orowan mechanism and dislocation generation effect by the coefficient of thermal expansion mismatch between the TiB2 nanoparticles and the matrix.Conference Object Development of Graphene Nanoplatelets Reinforced Aluminium Matrix Nanocomposites by a Combination of Semi-Solid Stirring and Ultrasonic Treatment(European Conference on Composite Materials, 2016) Kandemir, Sinan; Aydoğan, YücelGraphene Nanoplatelets (GNPs) consisting of graphene layers with a thickness less than 100 nm have recently emerged as a promising reinforcement type owing to their excellent physical and mechanical properties to improve mechanical properties of alloys beyond ceramic nanoparticles. Although there are numerous studies on GNPs reinforced polymer matrix composites in the literature, the number of studies related to the incorporation of GNPs in metal matrices is limited. It is a challenging task to incorporate and uniformly distribute GNPs into liquid metals due to their poor wettability and large surface-to-volume ratio. The purpose of this study is to effectively disperse GNPs into liquid aluminium. 0.5 wt.% GNPs with an average thickness of 50-100 nm and size of 5 ?m were first incorporated into A360 aluminium alloy under semi-solid stirring, and then the composite was ultrasonically treated in fully liquid state. The microstructural investigation of the nanocomposites by optical and scanning electron microscopy may suggest that relatively uniform distribution and effective deagglomeration of GNPs in the matrix were achieved. The hardness of the GNPs reinforced nanocomposites increased in comparison with that of semi-solid stirred and ultrasonically processed A360 alloy without reinforcement, indicating the potential of GNPs for strengthening metals. © 2016, European Conference on Composite Materials, ECCM. All rights reserved.Article Citation - WoS: 35Citation - Scopus: 39Development of Graphene Nanoplatelet-Reinforced Az91 Magnesium Alloy by Solidification Processing(Springer Verlag, 2018) Kandemir, SinanIt is a challenging task to effectively incorporate graphene nanoplatelets (GNPs) which have recently emerged as potential reinforcement for strengthening metals into magnesium-based matrices by conventional solidification processes due to their large surface areas and poor wettability. A solidification processing which combines mechanical stirring and ultrasonic dispersion of reinforcements in liquid matrix was employed to develop AZ91 magnesium alloy matrix composites reinforced with 0.25 and 0.5 wt.% GNPs. The microstructural studies conducted with scanning and transmission electron microscopes revealed that fairly uniform distribution and dispersion of GNPs through the matrix were achieved due to effective combination of mechanical and ultrasonic stirring. The GNPs embedded into the magnesium matrix led to significant enhancement in the hardness, tensile strength and ductility of the composites compared to those of unreinforced AZ91 alloy. The strength enhancement was predominantly attributed to the grain refinement by the GNP addition and dislocation generation strengthening due to the coefficient of thermal expansion mismatch between the matrix and reinforcement. The improved ductility was attributed to the refinement of β eutectics by transforming from lamellar to the divorced eutectics due to the GNP additions. In addition, the strengthening efficiency of the composite with 0.25 wt.% GNP was found to be higher than those of the composite with 0.5 wt.% GNP as the agglomeration tendency of GNPs is increased with increasing GNP content. These results were compared with those of the GNP-reinforced magnesium composites reported in the literature, indicating the potential of the process introduced in this study in terms of fabricating light and high-performance metal matrix composites.