Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
4 results
Search Results
Article Citation - WoS: 103Citation - Scopus: 113Preparation and Characterizations of Tio2/Zno Nanohybrid and Its Application in Photocatalytic Degradation of Tetracycline in Wastewater(Elsevier, 2023) Zeinali Heris, Saeed; Etemadi, Martin; Mousavi, Seyed Borhan; Mohammadpourfard, Mousa; Ramavandi, BahmanThe photodegradation of tetracycline antibiotics (TC) in an aqueous solution, using the TiO2 nanoparticles, ZnO microparticles, and TiO2/ZnO composite under the UV lamp in a continuous reactor, was performed. The effects of different parameters, such as the initial TC concentration, medium pH, ratio of each photocatalyst, and the flow rate were comprehensively studied. SEM, EDX, and XRD characterization techniques were employed to study the morphology and structure features of the prepared composite. The results revealed that a more significant amount of TC is not easily removed from wastewater. Furthermore, by increasing the pH of the medium to 11, the efficiency of TC degradation was increased, while the amount of removal remained stable at higher pH values. As the flow rate increased up to 190 mL/min, the removal efficiency increased; however, at higher flow rates, lower efficiency was obtained. Moreover, using multivariate analysis and response surface methodology (RSM), a model for removing TC and the effect of experimental parameters on removal efficiency was proposed. The optimal conditions using the RSM method were found to be the reduction efficiency of 78.94 % in pH = 11 (flow rate of 132 mL/min, and TiO2 concentration of 323 mg) and reduction efficiency of 75.89% in pH = 9 (flow rate of 143.19 mL/min and TiO2 concentration of 312.73 mg). © 2023 Elsevier B.V.Article Citation - WoS: 29Citation - Scopus: 33The Effect of Heat Transfer Characteristics of Macromolecule Fouling on Heat Exchanger Surface: a Dynamic Simulation Study(Wiley, 2023) Karimi Shoar, Zahra; Pourpasha, Hadi; Zeinali Heris, Saeed; Mousavi, Seyed Borhan; Mohammadpourfard, MousaAt the city gate gas pressure reduction stations (CGSs), to prevent natural gas from forming a hydrate in the throttle valve, the natural gas is heated by the heater before reaching the pressure relief valve. Heat exchangers are an essential component of industrial processes that contribute significantly to total system energy. Since the element impacting heat exchanger performance is the fouling process, all fouling processes and models were dynamically simulated in this study. Through coding in the C++ language and simultaneous use of fluent functions, or, in other words, user-defined function (UDF), fouling-related models were defined for this software. The dynamic simulation was performed, and parameters such as fouling strength and layer thickness were calculated. The effects of changing operating conditions, such as gas inlet velocity, surface temperature, and fouling species concentration on fouling growth, were also evaluated. As the concentration of fouling species increased, the fouling rate also increased. The amount of supersaturation and fouling rate increased as the surface temperature increased. Due to the operational limitations of the system, to reduce the fouling rate, the gas inlet velocity should be as high as possible, and the fluid inlet temperature, surface temperature, and concentration of fouling species should be as low as possible. In this study, the required time to reach the efficiency of 70% of the heat exchanger was calculated using the modelling of this chamber, which was equivalent to 190 days. Additionally, the critical thickness of the fouling layer at this time was 3.5 cm.Article Citation - WoS: 45Citation - Scopus: 31Highly Efficient Treatment of Petrochemical Spent Caustic Effluent Via Electro-Fenton Process for Cod and Toc Removal: Optimization and Experimental(Springer, 2023) Gholami, Asma; Mousavi, Seyed Borhan; Heris, Saeed Zeinali; Mohammadpourfard, MousaCaustic is commonly used in oil and gas refineries to remove CO2, H2S, organic sulfur, and acidic compounds; however, spent caustic must be treated considering the type of wastewater in refinery and petrochemical units due to their hazardous characteristics. This research aims to reduce the chemical oxygen demand (COD) and the total organic carbon (TOC) from the used caustic effluent of the olefin unit of Ilam Petrochemical Company employing the electro-Fenton method. The affecting parameters, such as H2O2 concentration, reaction time, pH, and current density on the COD and TOC removal rate, were investigated. An experimental design by response surface methodology (RSM) based on the Box–Behnken method with the considered factors was considered to study the setup’s effectiveness and optimize the conditions. The outcomes revealed that by increasing the H2O2 concentration from 11 to 18 mgL, the COD removal efficiency was enhanced from 68 to 93%. On the other hand, by increasing the reaction time after 15 min, the COD and TOC removal efficiency decreased. The same trend was observed by increasing the current density after the optimal value. The optimal conditions were acquired at pH = 4, current density = 20 mAcm2, H2O2 concentration = 18 mgL, and reaction time = 15 min. The promising results confirmed that the electro-Fenton could be an excellent treatment technique in Ilam Petrochemical Unit as a spent caustic treatment. © 2023, The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.Article Citation - WoS: 71Citation - Scopus: 78Investigation of H2o2/Uv Advanced Oxidation Process on the Removal Rate of Coliforms From the Industrial Effluent: a Pilot-Scale Study(Elsevier, 2022) Ashrafivala, Meisam; Mousavi, Seyed Borhan; Zeinali Heris, Saeed; Heidari, Mohammad; Mohammadpourfard, Mousa; Aslani, HassanWastewater recycling and reuse is very important, specially in countries with water shortage problem. Disinfection is very crucial step of wastewater treatment, particulary from the reuse and environmental protection point of view. In this research, the efficiency of the advanced oxidation process using UV and H2O2 combination was investigated on fecal coliform (FC) inactivation from a real industrial effluent; furthermore, the optimal condition for disinfection of the effluent using various parameters such as pH, H2O2 concentration, and contact time was determined. Based on the acquired outcomes, by pH decline from 11 to 7 and 3 inactivation rate increased (6.7% and 20.9%, sequentially), indicating the efficacy of acidic condition on the process. Increasing H2O2 concentration from 5 mg/L to 15 mg/L, 25 mg/L, and 35 mg/L, was led to increase FC inactivation by 16.6%, 29.75%, and 36.33%, respectively. Considering contcat time impact on the process performance, our findings revealed that the best efficiency obtained after 40 (s) contact time. It can be concluded that the combined UV/H2O2 is more potent than single UV and H2O2 process, making it possible to reach irrigation standards.