Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
24 results
Search Results
Article Citation - WoS: 56Citation - Scopus: 63Processing, Characterization and Photocatalytic Properties of Cu Doped Tio2 Thin Films on Glass Substrate by Sol-Gel Technique(Elsevier Ltd., 2006) Çelik, Erdal; Gökçen, Z.; Azem, N. Funda Ak; Tanoğlu, Metin; Emrullahoğlu, O. F.The present paper describes processing, properties and photocatalytic application of Cu doped TiO2 thin films on glass substrate. Cu doped TiO2 coatings were successfully prepared on glass slide substrates using sol-gel method. The obtained solutions exhibit acidic characteristics. The phase structure, thermal, microstructure and surface properties of the coatings were characterized by using XRD, DTA/TG, SEM and AFM. Their adhesion properties and spectroscopic analysis were investigated by a scratch tester and UV-vis spectroscopy. Four different solutions were prepared by changing Cu/Ti ratios. Glass substrates were coated by solutions of Ti-alkoxide, Cu-chloride, glacial acetic acid and isopropanol. The obtained gel films were dried at 300 degrees C for 10 min and subsequently heat-treated at 500 degrees C for 5 min in air. The oxide thin films were annealed at 600 degrees C for 60min in air. TiO2, CuO, Cu4Ti, Ti3O5 and Cu3TiO4 phases were found in the coating. The organic matters were burned at temperatures between 200 and 350 degrees C and TiO2 crystallization was formed at 450 degrees C. The weight loss of the powder during process up to 600 degrees C is approximately 70%. The microstructural observations demonstrated that CuO content was led an improved surface morphology while thickness of the film and surface defects were increased in accordance with number of dipping. According to AFM results, it was found that as the Cu/Ti content increases the surface roughness of the films increases. In addition structural, thermal and microstructural results, it was found that the films of 0.73 ratio have better adhesion strength to the glass substrate among other coatings. The oxide films were found to be active for photocatalytic decomposition of metylene blue. (c) 2006 Published by Elsevier B.V.Article Citation - WoS: 97Citation - Scopus: 110Effect of Polyamide-6,6 (pa 66) Nonwoven Veils on the Mechanical Performance of Carbon Fiber/Epoxy Composites(Elsevier Ltd., 2018) Beylergil, Bertan; Tanoğlu, Metin; Aktaş, EnginIn this study, carbon fiber/epoxy (CF/EP) composites were interleaved with polyamide-6,6 (PA 66) nonwoven veils at two different areal weight densities (17 and 50 gsm) to improve their delamination resistance against Mode-I loading. Mode-I fracture toughness (DCB), tensile, open hole tensile (OHT), flexural, compression, short beam shear (ILSS) and Charpy-impact tests were performed on the reference and PA 66 interleaved composite specimens. The DCB test results showed that the initiation and propagation Mode-I fracture toughness values of the composites were significantly improved by 84 and 171% using PA 66-17 gsm veils respectively, as compared to reference laminates. The use of denser PA 66-50 gsm veils in the interlaminar region led to higher improvement in fracture toughness values (349% for initiation and 718% for propagation) due to the higher amount of veil fibers involved in fiber bridging toughening mechanism. The incorporation of PA 66-50 gsm nonwoven veils also increased the ILSS and Charpy impact strength of the composites by 25 and 15%, respectively. On the other hand, the PA 66 veils reduced in-plane mechanical properties of CF/EP composites due to lower carbon fiber volume fraction and increased thickness.Article Citation - WoS: 15Citation - Scopus: 14Development of Electrically Conductive and Anisotropic Gel-Coat Systems Using Cnts(Elsevier Ltd., 2013) İnce Yardımcı, Atike; Tanoğlu, Metin; Selamet, YusufElectrical conductivity of an unsaturated thermoset polyester based gel-coat system containing 0.05 wt.% of carbon nanotubes (CNTs) was investigated. The CNTs used were synthesized by chemical vapor deposition method by methane decomposition and Raman characterization showed that they were mostly single walled and high quality. To disperse CNTs in the gel-coat resin, 3-roll milling technique was used. It was found that as the CNTs are added to gel-coat system, resistivity value decreases significantly while neat gel-coat showed a high resistivity. By the application of an AC electrical field during curing process, it was attempted to align CNTs in the gel-coat resin and an electrically anisotropic polymer was obtained. © 2012 Elsevier B.V. All rights reserved.Article Citation - WoS: 25Citation - Scopus: 25Characterization Investigations During Mechanical Alloying and Sintering of W-20 Vol% Sic Composites(Elsevier Ltd., 2010) Coşkun, Selim; Öveçoğlu, M. Lütfi; Özkal, Burak; Tanoğlu, MetinThe effect of mechanical alloying and the sintering regime on the microstructural and the physical properties of W-SiC composites were investigated. Powder mixtures of W-20 vol.% SiC were mechanically alloyed (MA'd) using a Spex mill for 3 h, 6 h and 24 h. MA'd powders were characterized by Laser Diffraction Particle Size Analyzer, SEM and XRD investigations. MA'd W-20 vol.% SiC powder composites were sintered under inert Ar and reducing H2 gas conditions at 1680 °C and 1770 °C for 1 h. The microstructural and mechanical characterizations of the sintered samples were carried out by scanning electron microscope (SEM) and X-ray diffraction (XRD) and Vickers Hardness analyses. The addition of SiC remarkably increases the hardness of the composites. Hardness is also increased with decreasing grain size and increasing amount of MA. © 2009 Elsevier B.V. All rights reserved.Article Citation - WoS: 23Citation - Scopus: 27Electric Field Effects on Cnts/Vinyl Ester Suspensions and the Resulting Electrical and Thermal Composite Properties(Elsevier Ltd., 2010) Yurdakul, Hilmi; Seyhan, Abdullah Tuğrul; Turan, Servet; Tanoğlu, Metin; Bauhofer, Wolfgang; Schulte, KarlIn this study, electrical conductivity of a vinyl ester based composite containing low content (0.05, 0.1 and 0.3wt.%) of double and multi-walled carbon nanotubes with and without amine functional groups (DWCNTs, MWCNTs, DWCNT-NH2 and MWCNT-NH2) was investigated. The composite with pristine MWCNTs was found to exhibit the highest electrical conductivity. Experiments aimed to induce an aligned conductive network with application of an alternating current (AC) electric field during cure were carried out on the resin suspensions with MWCNTs. Formation of electric anisotropy within the composite was verified. Light microscopy (LM), scanning electron (SEM) and transmission electron microscopy (TEM) were conducted to visualize dispersion state and the extent of alignment of MWCNTs within the polymer cured with and without application of the electric field. To gain a better understanding of electric field induced effects, glass transition temperature (Tg) of the composites was measured via Differential Scanning Calorimetry (DSC). It was determined that at 0.05wt.% loading rate of MWCNTs, the composites, cured with application of the AC electric field, possessed a higher Tg than the composites cured without application of the AC electric field. © 2010 Elsevier Ltd.Article Citation - WoS: 73Citation - Scopus: 92Tensile Mechanical Behavior and Fracture Toughness of Mwcnt and Dwcnt Modified Vinyl-ester/Polyester Hybrid Nanocomposites Produced by 3-Roll Milling(Elsevier Ltd., 2009) Seyhan, Abdullah Tuğrul; Tanoğlu, Metin; Schulte, KarlThis study aims to investigate the tensile mechanical behavior and fracture toughness of vinyl-ester/polyester hybrid nanocomposites containing various types of nanofillers, including multi- and double-walled carbon nanotubes with and without amine functional groups (MWCNTs, DWCNTs, MWCNT-NH2 and DWCNT-NH2). To prepare the resin suspensions, very low contents (0.05, 0.1 and 0.3 wt.%) of carbon nanotubes (CNTs) were dispersed within a specially synthesized styrene-free polyester resin, conducting 3-roll milling technique. The collected resin stuff was subsequently blended with vinyl-ester via mechanical stirring to achieve final suspensions prior to polymerization. Nanocomposites containing MWCNTs and MWCNT-NH2 were found to exhibit higher tensile strength and modulus as well as larger fracture toughness and fracture energy compared to neat hybrid polymer. However, incorporation of similar contents of DWCNTs and DWCNT-NH2 into the hybrid resin did not reflect the same improvement in the corresponding mechanical properties. Furthermore, experimentally measured elastic moduli of the nanocomposites containing DWCNTs, DWCNT-NH2, MWCNTs and MWCNT-NH2 were fitted to Halphin-Tsai model. Regardless of amine functional groups or content of carbon nanotubes, MWCNT modified nanocomposites exhibited better agreement between the predicted and the measured elastic moduli values compared to nanocomposites with DWCNTs. Furthermore, Transmission Electron Microscopy (TEM) and Scanning Electron Microscopy (SEM) were used to reveal dispersion state of the carbon nanotubes within the hybrid polymer and to examine the CNT induced failure modes that occurred under mechanical loading, respectively. Based on the experimental findings obtained, it was emphasized that the types of CNTs and presence of amine functional groups on the surface of CNTs affects substantially the chemical interactions at the interface, thus tuning the ultimate mechanical performance of the resulting nanocomposites.Article Citation - WoS: 24Citation - Scopus: 26Cure Kinetics of Vapor Grown Carbon Nanofiber (vgcnf) Modified Epoxy Resin Suspensions and Fracture Toughness of Their Resulting Nanocomposites(Elsevier Ltd., 2009) Seyhan, Abdullah Tuğrul; Sun, Z.; Deitzel, J.; Tanoğlu, Metin; Heider, D.In this study, the cure kinetics of Cycom 977-20, an aerospace grade toughened epoxy resin, and its suspensions containing various amounts (1, 3 and 5 wt.%) of vapor grown carbon nanofibers (VGCNFs) with and without chemical treatment were monitored via dynamic and isothermal dynamic scanning calorimetry (DSC) measurements. For this purpose, VGCNFs were first oxidized in nitric acid and then functionalized with 3-glycidoxypropyltrimethoxy silane (GPTMS) coupling agent. Fourier transform infrared (FTIR) spectroscopy was subsequently used to verify the chemical functional groups grafted onto the surfaces of VGCNFs. Sonication technique was conducted to facilitate proper dispersion of as-received, acid treated and silanized VGCNFs within epoxy resin. Dynamic DSC measurements showed that silanized VGCNF modified resin suspensions exhibited higher heat of cure compared to those with as-received VGCNFs. Experimentally obtained isothermal DSC data was then correlated with Kamal phenomenological model. Based on the model predictions, it was found that silanized VGCNFs maximized the cure reaction rates at the very initial stage of the reaction. Accordingly, an optimized curing cycle was applied to harden resin suspensions. Fracture testing was then carried out on the cured samples in order to relate the curing behavior of VGCNF modified resin suspensions to mechanical response of their resulting nanocomposites. With addition of 1 wt.% of silanized VGCNFs, the fracture toughness value of neat epoxy was found to be improved by 12%. SEM was further employed to examine the fracture surfaces of the samples.Article Citation - WoS: 16Citation - Scopus: 17Porous Nanocomposites Prepared From Layered Clay and Pmma [poly(methyl Methacrylate)](Elsevier Ltd., 2007) Tanoğlu, Metin; Ergün, YeldaThe aim of the present work is the preparation of PMMA based porous nanocomposites that contain clay (montmorillonite, MMT) platelets as reinforcements within the cell walls of the porous structure. To render the clay layers organophilic, MMT was surface treated by an ion exchange reaction between interlayer cations of the clay and ammonium ions of a surfactant. Clay/PMMA based porous nanocomposites were prepared by polymerization of water-in-oil emulsions with and without clay addition. The microstructure and compressive mechanical behavior of the nanocomposites were investigated. The results of mechanical tests showed that the porous systems with the addition of 1 wt.% of organoclay (OMMT) exhibited a 90% and 50% increase of collapse stress and elastic modulus values, respectively, as compared to neat porous PMMA.Article Citation - WoS: 78Citation - Scopus: 106Critical Aspects Related To Processing of Carbon Nanotube/Unsaturated Thermoset Polyester Nanocomposites(Elsevier Ltd., 2007) Seyhan, Abdullah Tuğrul; Gojny, Florian H.; Tanoğlu, Metin; Schulte, KarlCarbon nanotubes (CNTs) have outstanding mechanical, thermal and electrical properties. As a result, particular interest has been recently given in exploiting these properties by incorporating carbon nanotubes into some form of matrix. Although unsaturated polyesters with styrene have widespread use in the industrial applications, surprisingly there is no study in the literature about CNT/thermoset polyester nanocomposite systems. In the present paper, we underline some important issues and limitations during the processing of unsaturated polyester resins with different types of carbon nanotubes. In that manner, 3-roll mill and sonication techniques were comparatively evaluated to process nanocomposites made of CNTs with and without amine (NH2) functional groups and polyesters. It was found that styrene evaporation from the polyester resin system was a critical issue for nanocomposite processing. Rheological behaviour of the suspensions containing CNTs and tensile strengths of their resulting nanocomposites were characterized. CNT/polyester suspensions exhibited a shear thinning behaviour, while polyester resin blends act as a Newtonian fluid. It was also found that nanotubes with amine functional groups have better tensile strength, as compared to those with untreated CNTs. Transmission electron microscopy (TEM) was also employed to reveal the degree of dispersion of CNTs in the matrix.Article Citation - WoS: 46Citation - Scopus: 53Preparation and Characterization of Fe2o3-Tio2 Thin Films on Glass Substrate for Photocatalytic Applications(Elsevier Ltd., 2006) Çelik, Erdal; Yıldız, A. Y.; Ak Azem, Necmiye Funda; Tanoğlu, Metin; Toparlı, Mustafa; Emrullahoğlu, Ö. Faruk; Özdemir, İ.Fe2O3-TiO2 coatings were successfully prepared on glass slide substrates using sol-gel method for photocatalytic applications. The phase structure, thermal, microstructure and surface properties of the coatings were extensively characterized by using X-ray diffractometry (XRD), differential thermal analysis/thermograviometry (DTA/TG), scanning electron microscopy (SEM) and atomic force microscopy (AFM). Their adhesion and absorbance properties were investigated by a scratch tester and UV-vis spectroscopy. Four different solutions were prepared by changing Fe/Ti molar ratios. Glass substrates were coated by solutions of Ti-alkoxide, Fe-chloride, glaciel acetic acid and isopropanol. The obtained gel films were dried at 300 °C for 10 min and subsequently heat-treated at 500 °C for 5 min in air. The oxide thin films were annealed at 600 °C for 60 min in air. The influence of Fe3+ concentration and number of layers on structure of the films was established. In addition, XRD results revealed that Fe2O3-TiO2 films composed of TiO2, Fe2Ti3O9, Ti3O5 and Fe3O4 phases. According to DTA/TG result, it was determined that endothermic and exothermic reactions were formed at temperatures between 80 and 650 °C due to solvent removal, combustion of carbon based materials and oxidation of Fe and Ti. SEM observations exhibited that the coating structure becomes more homogeneous depending on an increase of Fe/Ti molar ratios and thus a regular surface morphology forms with increasing Fe/Ti ratio. It was also seen that as the Fe/Ti ratio increases the surface roughness of the films increases. Critical adhesion force of thin films with Fe/Ti ratio of 0, 0.07, 0.18 and 0.73 were found to be 9, 25, 28 and 21 mN, respectively. The methylene blue solutions photocatalyzed by TiO2 based thin films shows characteristic absorption bands at 420 nm.
- «
- 1 (current)
- 2
- 3
- »