Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
19 results
Search Results
Article Citation - WoS: 15Citation - Scopus: 17Effects of Nanosecond Laser Ablation Parameters on Surface Modification of Carbon Fiber Reinforced Polymer Composites(SAGE Publications, 2023) Martin, Seçkin; İplikçi, Hande; Barışık, Murat; Türkdoğan, Ceren; Yeke, Melisa; Nuhoğlu, Kaan; Esenoğlu, Gözde; Tanoğlu, Metin; Aktaş, Engin; Dehneliler, Serkan; İriş, Mehmet ErdemRemoval of contaminants and top polymer layer from the surface of carbon-fiber-reinforced polymer (CFRP) composites is critical for high-quality adhesive-joining with direct bonding to the reinforcing fiber constituents. Surface treatment with a laser beam provides selective removal of the polymer matrix without damaging the fibers and increasing the wettability. However, inhomogeneous thermal properties of CFRP make control of laser ablation difficult as the laser energy absorbed by the carbon fibers is converted into heat and transmitted through the fiber structures during the laser operation. In this study, the effect of scanning speed and laser power on nanosecond laser surface treatment was characterized by scanning electron microscope images and wetting angle measurements. Low scanning speeds allowed laser energy to be conducted as thermal energy through the fibers, which resulted in less epoxy matrix removal and substantial thermal damage. Low laser power partially degraded the epoxy the surface while the high power damaged the carbon fibers. For the studied CFRP specimens consisting of unidirectional [45/0/?45/90]2s stacking of carbon/epoxy prepregs (HexPly®-M91), 100 mJ/mm2 generated by 10 m/s scanning speed and 30 W power appeared as optimum processing parameters for the complete removal of epoxy matrix from the top surface with mostly undamaged carbon fibers and super hydrophilic surface condition. © The Author(s) 2023.Article Citation - WoS: 8Citation - Scopus: 8Improving Adhesive Behavior of Fiber Reinforced Composites by Incorporating Electrospun Polyamide-6,6 Nanofibers in Joining Region(SAGE Publications, 2022) Esenoğlu, Gözde; Barışık, Murat; Tanoğlu, Metin; Yeke, Melisa; Türkdoğan, Ceren; İplikçi, Hande; Martin, Seçkin; Nuhoğlu, Kaan; Aktaş, Engin; Dehneliler, Serkan; İriş, Mehmet ErdemAdhesive joining of fiber reinforced polymer (CFRP) composite components is demanded in various industrial applications. However, the joining locations frequently suffer from adhesive bond failure between adhesive and adherent. The aim of the present study is improving bonding behavior of adhesive joints by electrospun nanofiber coatings on the prepreg surfaces that have been used for composite manufacturing. Secondary bonding of woven and unidirectional CFRP parts was selected since this configuration is preferred commonly in aerospace practices. The optimum nanofiber coating with a low average fiber diameter and areal weight density is succeed by studying various solution concentrations and spinning durations of the polyamide-6.6 (PA 66) electrospinning. We obtained homogeneous and beadles nanofiber productions. As a result, an average diameter of 36.50 +/- 12 nm electrospun nanofibers were obtained and coated onto the prepreg surfaces. Prepreg systems with/without PA 66 nanofibers were hot pressed to fabricate the CFRP composite laminates. The single-lap shear test coupons were prepared from the fabricated laminates to examine the effects of PA 66 nanofibers on the mechanical properties of the joint region of the composites. The single-lap shear test results showed that the bonding strength is improved by about 40% with minimal adhesive use due to the presence of the electrospun nanofibers within the joint region. The optical and SEM images of fractured surfaces showed that nanofiber-coated joints exhibited a coherent failure while the bare surfaces underwent adhesive failure. The PA66 nanofibers created better coupling between the adhesive and the composite surface by increasing the surface area and roughness. As a result, electrospun nanofibers turned adhesive failure into cohesive and enhanced the adhesion performance composite joints substantially.Article Citation - WoS: 3Citation - Scopus: 3Determination of Activation Energy for Carbon/Epoxy Prepregs Containing Carbon Nanotubes by Differential Scanning Calorimetry(SAGE Publications, 2022) Uz, Yusuf Can; Tanoğlu, MetinThe aim of the present study is the thermal characterization of laboratory-scale carbon fiber/epoxy-based prepregs by incorporating single-wall carbon nanotubes (SWCNTs). Investigation of the cure behavior of a prepreg system is crucial for the characterization and optimization of the fiber reinforced polymeric (FRP) composite. To affect dispersion characteristics, SWCNTs were functionalized by oxidizing their surface with carboxyl (-COOH) group using an acid treatment. The modified resin system contained 0.05, 0.1, and 0.2 wt. % functionalized SWCNTs (F-SWCNTs). Carbon fiber (CF) reinforced prepregs containing various amount of F-SWCNTs were prepared using drum-type winding technique. FTIR was performed to identify new bonding groups formed after the functionalization of SWCNTs. Cure kinetics of prepregs prepared with/without F-SWCNTs were investigated using isoconversional methods.Article Citation - WoS: 1Citation - Scopus: 1Fatigue Life Prediction and Optimization of Gfrp Composites Based on Failure Tensor Polynomial in Fatigue Model With Exponential Fitting Approach(SAGE Publications, 2022) Güneş, Mehmet Deniz; İmamoğlu Karabaş, Neslişah; Deveci, Hamza Arda; Tanoğlu, Gamze; Tanoğlu, MetinIn this study, a new fatigue life prediction and optimization strategy utilizing the Failure Tensor Polynomial in Fatigue (FTPF) model with exponential fitting and numerical bisection method for fiber reinforced polymer composites has been proposed. Within the experimental stage, glass/epoxy composite laminates with (Formula presented.), (Formula presented.), and (Formula presented.) lay-up configurations were fabricated, quasi-static and fatigue mechanical behavior of GFRP composites was characterized to be used in the FTPF model. The prediction capability of the FTPF model was tested based on the experimental data obtained for multidirectional laminates of various composite materials. Fatigue life prediction results of the glass/epoxy laminates were found to be better as compared to those for the linear fitting predictions. The results also indicated that the approach with exponential fitting provides better fatigue life predictions as compared to those obtained by linear fitting, especially for glass/epoxy laminates. Moreover, an optimization study using the proposed methodology for fatigue life advancement of the glass/epoxy laminates was performed by a powerful hybrid algorithm, PSA/GPSA. So, two optimization scenarios including various loading configurations were considered. The optimization results exhibited that the optimized stacking sequences having maximized fatigue life can be obtained in various loading cases. It was also revealed that the tension-compression loading and the loadings involving shear loads are critical for fatigue, and further improvement in fatigue life may be achieved by designing only symmetric lay-ups instead of symmetric-balanced and diversification of fiber angles to be used in the optimization.Article Citation - WoS: 9Citation - Scopus: 10Investigation of Hybridization Effect on Ballistic Performance of Multi-Layered Fiber Reinforced Composite Structures(Sage Publications Ltd, 2022) Üstün, Hikmet Sinan; Toksoy, Ahmet Kaan; Tanoğlu, MetinThe aim of this study is enhancing the ballistic performance of multi-layered fiber reinforced composite structures by hybridization approach against fragment simulating projectile (FSP). For manufacturing of homogeneous and hybrid composite structures, 170 g/m2 twill weave aramid and 280 g/m2 plain weave E-Glass fibers were used with epoxy resin systems and two different thickness values for each composite panel were fabricated and tested to obtain a relationship between areal density and V50 parameters. Tensile, 3-point bending, and short beam strength tests of composite panels were performed, and ballistic performance of composite structures were measured by V50 test method with 1.1 g FSP threat. Ballistic performance of hybrid composite structures was compared with high-performance composite ballistic panel test results reported in literature. As a result, it was found that E-Glass fabric layers together with aramid fabrics increased the energy absorbing capability of hybrid composite panels and ballistic performance was enhanced to be similar or higher than ballistic fiber reinforced composites. Hence, hybridization was found to be an effective way to enhance ballistic performance of fiber reinforced composite structures.Article Citation - WoS: 7Citation - Scopus: 7A Comprehensive Study on Burst Pressure Performance of Aluminum Liner for Hydrogen Storage Vessels(ASME, 2021) Kangal, Serkan; Sayı, Abdülmecit Harun; Ayakdaş, Ozan; Kartav, Osman; Aydın, Levent; Artem, Hatice Seçil; Aktaş, Engin; Yücetürk, Kutay; Tanoğlu, Metin; Kandemir, Sinan; Beylergil, BertanThis paper presents a comparative study on the burst pressure performance of aluminum (Al) liner for type-III composite overwrapped pressure vessels (COPVs). In the analysis, the vessels were loaded with increasing internal pressure up to the burst pressure level. In the analytical part of the study, the burst pressure of the cylindrical part was predicted based on the modified von Mises, Tresca, and average shear stress criterion (ASSC). In the numerical analysis, a finite element (FE) model was established in order to predict the behavior of the vessel as a function of increasing internal pressure and determine the final burst. The Al pressure vessels made of Al-6061-T6 alloy with a capacity of 5 L were designed. The manufacturing of the metallic vessels was purchased from a metal forming company. The experimental study was conducted by pressurizing the Al vessels until the burst failure occurred. The radial and axial strain behaviors were monitored at various locations on the vessels during loading. The results obtained through analytical, numerical, and experimental work were compared. The average experimental burst pressure of the vessels was found to be 279 bar. The experimental strain data were compared with the results of the FE analysis. The results indicated that the FE analysis and ASSC-based elastoplastic analytical approaches yielded the best predictions which are within 2.2% of the experimental burst failure values. It was also found that the elastic analysis underestimated the burst failure results; however, it was effective for determining the critical regions over the vessel structure. The strain behavior of the vessels obtained through experimental investigations was well correlated with those predicted through FE analysis.Article Citation - WoS: 31Citation - Scopus: 32Development and Analysis of Composite Overwrapped Pressure Vessels for Hydrogen Storage(SAGE Publications, 2021) Kartav, Osman; Kangal, Serkan; Yücetürk, Kutay; Tanoğlu, Metin; Aktaş, Engin; Artem, Hatice SeçilIn this study, composite overwrapped pressure vessels (COPVs) for high-pressure hydrogen storage were designed, modeled by finite element (FE) method, manufactured by filament winding technique and tested for burst pressure. Aluminum 6061-T6 was selected as a metallic liner material. Epoxy impregnated carbon filaments were overwrapped over the liner with a winding angle of +/- 14 degrees to obtain fully overwrapped composite reinforced vessels with non-identical front and back dome layers. The COPVs were loaded with increasing internal pressure up to the burst pressure level. During loading, deformation of the vessels was measured locally with strain gauges. The mechanical performances of COPVs designed with various number of helical, hoop and doily layers were investigated by both experimental and numerical methods. In numerical method, FE analysis containing a simple progressive damage model available in ANSYS software package for the composite section was performed. The results revealed that the FE model provides a good correlation as compared to experimental strain results for the developed COPVs. The burst pressure test results showed that integration of doily layers to the filament winding process resulted with an improvement of the COPVs performance.Article Citation - WoS: 21Citation - Scopus: 24Development and Mechanical Behavior of Fml/Aluminium Foam Sandwiches(Springer Verlag, 2013) Baştürk, Suat Bahar; Tanoğlu, MetinIn this study, the Fiber-Metal Laminates (FMLs) containing glass fiber reinforced polypropylene (GFPP) and aluminum (Al) sheet were consolidated with Al foam cores for preparing the sandwich panels. The aim of this article is the comparison of the flexural properties of FML/Al foam sandwich panels bonded with various surface modification approaches (silane treatment and combination of silane treatment with polypropylene (PP) based film addition). The FML/foam sandwich systems were fabricated by laminating the components in a mould at 200 A degrees C under 1.5 MPa pressure. The energy absorbtion capacities and flexural mechanical properties of the prepared sandwich systems were evaluated by mechanical tests. Experiments were performed on samples of varying foam thicknesses (8, 20 and 30 mm). The bonding among the sandwich components were achieved by various surface modification techniques. The Al sheet/Al foam sandwiches were also consolidated by bonding the components with an epoxy adhesive to reveal the effect of GFPP on the flexural performance of the sandwich structures.Article Citation - WoS: 11Citation - Scopus: 13Effect of Cnt Incorporation on Pan/Ppy Nanofibers Synthesized by Electrospinning Method(TÜBİTAK, 2020) İnce Yardımcı, Atike; Tanoğlu, Metin; Yılmaz, Selahattin; Selamet, YusufIn this study, carbon nanotubes (CNTs) added polyacrylonitrile/polypyrrole (PAN/PPy) electrospun nanofibers were produced. Average diameters of the nanofibers were measured as 268 and 153 nm for 10 and 25 wt% of PPy contents, respectively. A relatively higher strain to failure values (23.3%) were observed for the low PPy content. When as-grown CNTs (1 and 4 wt%) were added into the PAN/PPy blends, disordered nanofibers were observed to form within the microstructure. To improve the interfacial properties of CNTs/PAN/PPy composites, CNTs were functionalized with H2SO4/HNO3/HCl solution. The functionalized CNTs were well dispersed within the nanofibers and aligned along the direction of nanofibers. Therefore, beads formation on nanofibers decreased. The impedance of the nanofibers was found to decrease with the PPy content and CNT addition. These nanofibers had a great potential to be used as an electrochemical actuator or a tissue engineering scaffold.Article Citation - WoS: 8Citation - Scopus: 8The Effect of Single-Walled Carbon Nanotube (swcnt) Concentration on the Mechanical and Rheological Behavior of Epoxy Matrix(Springer Verlag, 2020) Ay, Z.; Tanoğlu, MetinThe improvement of Mode I fracture toughness of epoxy by the addition of single-walled carbon nanotubes (SWCNTs) is considered. To prepare nanocomposites, chemical-vapor-deposition-grown SWCNTs noncovalently functionalized with an ethoxylated alcohol was used as the additive and a diglycidyl ether of bisphenol-A-based epoxy as the matrix material. The SWCNTs were dispersed in the epoxy matrix via a mechanical stirrer and a 3-roll mill. The effect of their concentration (0.0125, 0.025, 0.05, 0.1, 0.3, and 0.5 wt.%) on the mechanical properties of the nanocomposites was investigated, and the optimum concentration was determined. Mode I fracture toughness (single-edge-notch 3-point bending) and tensile tests were carried out on neat epoxy and SWCNT-reinforced epoxy nanocomposites. The fractured surfaces of fracture toughness and tensile test specimens were examined by the SEM to reveal the effect of SWCNTs on their failure modes.