Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
3 results
Search Results
Article Improving Doppler Radar Performance through Optically-Reconfigurable Unequal Power Division with Semi-Analytical Approach(Taylor & Francis Ltd, 2025) Karatay, Anil; Atac, Enes; Dinleyici, Mehmet Salih; Yaman, FatihThe improvement of the signal-to-noise ratio (SNR) of Doppler radar systems, enabling the detection of targets at greater ranges even with limited power, has been a longstanding focus of research. However, while key limitations such as low target reflectivity and environmental interference are often addressed, the impact of efficient use of the input power remains an overlooked, yet crucial factor in overall sensitivity. Additionally, the power allocation needs to be examined from an analytical perspective for further enhancement. In this study, we present a novel measurement approach, utilizing both semi-analytical analysis and experimental methods, to improve the performance of a dual-antenna CW Doppler radar through the use of an optically reconfigurable unequal microwave power divider which provides well-directed power utilization. Comprehensive grid searches, supported by an analytical approach and considering various loss and noise scenarios, demonstrate the capability of the proposed reconfiguration method. In the Doppler radar experiments where the pendulum and servo motor were used as targets, an SNR increase of 3.04 and 2.11 dB in the radar signal was observed with the proposed method, respectively. This noticeable improvement in the SNR of the time-frequency plots indicates an enhancement in the measurement performance. The unequal power allocation enabled continuous detection of target motion with minimal signal loss, lowering the minimum detectable power level by more than 2 dB compared to the equal power division case. The experimental results show that integrating an optically reconfigurable microwave power divider into the Doppler radar system increases precision in velocity measurements.Article Citation - WoS: 3Citation - Scopus: 3Liquid Metal-Tunable Miniaturized Bimodal Cavity for Enhanced Measurement Accuracy in the Ism Bands(Ieee-inst Electrical Electronics Engineers inc, 2024) Karatay, Anil; Yaman, FatihEnhancing measurement accuracy or reducing the effect of the neighboring modes in resonant cavities may necessitate the separation of mode frequencies. However, in ISM-band measurement configurations utilizing a rectangular or cylindrical cavity, the placement of the first two modes at 2.45 and 5.8 GHz is unattainable, necessitating the presence of additional modes in between that would potentially degrade measurement accuracy. This article begins with an analytical approach, employing Lagrange multipliers for the first time to reveal the level of separation achievable in the frequency domain between the initial two modes within these types of conventional cavities. The analytical results were also verified with a numerical grid search. Subsequently, innovative strategies have been introduced to surpass this intrinsic constraint that reduces the measurement accuracy in various applications. A novel miniaturized cavity configuration has been proposed to operate bimodally at 2.45 and 5.8 GHz and manufactured with a 3-D printer. It has been ensured that there are no physical modes present in between, and measurements of the structure have been conducted. Another notable innovation of the article is the capability of tuning the proposed cavity structure by means of liquid metal displacement. Thus, a more flexible tuning method compared to mechanical tuning techniques can be achieved, enabling precise adjustment of the desired measurement frequency. Good agreement between the simulation and measurement results has been reported.Article Citation - WoS: 3Citation - Scopus: 4Cost-Effective Experiments With Additively Manufactured Waveguide and Cavities in the S-Band(Iop Publishing Ltd, 2023) Karatay, Anıl; Yilmaz, Hasan Önder; Özkal, Ceren; Yaman, FatihThis study demonstrates the applicability of additively manufactured components that are metalized with conductive tape for two different microwave experiments. We focus on dielectric measurements and prototyping elliptical accelerator cavities at a low power regime for 2.45 GHz. To illustrate the accuracy of our results for the commonly used solid/liquid materials in engineering and to compare the fundamental accelerator cavity parameters with previous research rectangular and elliptic 3D-printed cavities coated with aluminum-type tape were employed in the experiments. Results reported for the complex-valued permittivities and specific design parameters for the cavity prototype are consistent with the literature. Various approaches to obtain the conductivity value of the tape and the effect of the roughness/thickness of the coating on the reflection parameter are discussed in detail. We confirm the effectiveness of the proposed approach, which reduces costs and provides a high degree of accuracy for investigated applications.