Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
19 results
Filters
Settings
Search Results
Article Citation - WoS: 8Citation - Scopus: 8A Review of the Experimental and Numerical Studies on the Compression Behavior of the Additively Produced Metallic Lattice Structures at High and Low Strain Rates(KeAi Communications Co., 2025) Bin Riaz, Muhammad Arslan; Guden, MustafaRecent advances in additive manufacturing have enabled the construction of metallic lattice structures with tailored mechanical and functional properties. One potential application of metallic lattice structures is in the impact load mitigation where an external kinetic energy is absorbed by the deformation/ crushing of lattice cells. This has motivated a growing number of experimental and numerical studies, recently, on the crushing behavior of additively produced lattice structures. The present study overviews the dynamic and quasi-static crushing behavior of additively produced Ti64, 316L, and AlSiMg alloy lattice structures. The first part of the study summarizes the main features of two most commonly used additive processing techniques for lattice structures, namely selective-laser-melt (SLM) and electrobeam-melt (EBM), along with a description of commonly observed process induced defects. In the second part, the deformation and strain rate sensitivities of the selected alloy lattices are outlined together with the most widely used dynamic test methods, followed by a part on the observed microstructures of the SLM and EBM-processed Ti64, 316L and AlSiMg alloys. Finally, the experimental and numerical studies on the quasi-static and dynamic compression behavior of the additively processed Ti6 4, 316L, and AlSiMg alloy lattices are reviewed. The results of the experimental and numerical studies of the dynamic properties of various types of lattices, including graded, non-uniform strut size, hollow, non-uniform cell size, and bio-inspired, were tabulated together with the used dynamic testing methods. The dynamic tests have been noted to be mostly conducted in compression Split Hopkinson Pressure Bar (SHPB) or Taylor-and direct-impact tests using the SHPB set-up, in all of which relatively small-size test specimens were tested. The test specimen size effect on the compression behavior of the lattices was further emphasized. It has also been shown that the lattices of Ti6 4 and AlSiMg alloys are relatively brittle as compared with the lattices of 316L alloy. Finally, the challenges associated with modelling lattice structures were explained and the micro tension tests and multi-scale modeling techniques combining microstructural characteristics with macroscopic lattice dynamics were recommended to improve the accuracy of the numerical simulations of the dynamic compression deformations of metallic lattice structures. (c) 2025 China Ordnance Society. Publishing services by Elsevier B.V. on behalf of KeAi Communications Co. Ltd. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/ licenses/by-nc-nd/4.0/).Article Citation - WoS: 8Citation - Scopus: 8A Comprehensive Study of the Effect of Scanning Strategy on In939 Fabricated by Powder Bed Fusion-Laser Beam(Elsevier, 2024) Dogu, Merve Nur; Ozer, Seren; Yalcin, Mustafa Alp; Davut, Kemal; Obeidi, Muhannad Ahmed; Simsir, Caner; Brabazon, DermotThis study provides a comprehensive investigation into the effects of different scanning strategies on the material properties of IN939 fabricated using the PBF-LB process. The scanning strategies examined included alternating bi-directional scanning with rotation angles of 0 degrees, 45 degrees, 67 degrees, and 90 degrees between adjacent layers (named as shown), as well as alternating chessboard scanning with rotation angles of 67 degrees and 90 degrees (named as Q67 degrees and Q90 degrees). The results revealed that the 45 degrees and 67 degrees samples had the highest relative density, while the 0 degrees and Q67 degrees samples showed the highest average porosity. Moreover, various types of cracks, including solidification, solid-state, and oxide-induced cracks, were observed. Among the bi-directional scan samples, the 0 degrees sample displayed the most extensive cracking and the highest sigma max residual stress values in both XZ and XY planes. Conversely, the 45 degrees and 67 degrees samples exhibited fewer cracks. Notably, the lowest sigma max residual stress in the XZ planes among the bidirectional scan samples was observed in the 67 degrees sample. Additionally, microstructural analyses indicated differences in grain size and morphology, among the samples. Texture analysis indicated that the 0 degrees and 90 degrees samples exhibited strong cube textures, whereas the texture intensity weakened for the 45 degrees and 67 degrees samples. Moreover, the alternating chessboard scanning strategy led to rougher surfaces (higher Sa and Sz values) compared to the alternating bi-directional scanning strategy, regardless of the rotation angles. Furthermore, the microhardness values among the samples showed minimal variance, ranging between 321 + 14 HV and 356+ 7 HV.Article Citation - WoS: 13Citation - Scopus: 11Effect of Aging Treatment on the Microstructure, Cracking Type and Crystallographic Texture of In939 Fabricated by Powder Bed Fusion-Laser Beam(Elsevier, 2024) Ozer, Seren; Dogu, Merve Nur; Ozdemirel, Ceren; Bilgin, Guney Mert; Gunes, Mert; Davut, Kemal; Brabazon, DermotThis study aimed to provide a comprehensive understanding of how aging treatments (namely, HT1 and HT2) affect the microstructure, cracking behavior, and crystallographic texture of IN939 fabricated by powder bed fusion-laser beam (PBF-LB) method. Although both aged samples demonstrated similar grain structure and recrystallization behavior according to the electron backscatter diffraction (EBSD) analysis, as well as the precipitation of bimodal gamma ' phase and MC- and M23C6-type carbides, notable differences were observed in the size and morphology, particularly the gamma ' phase. The HT1 sample displayed coarsened primary gamma ' phase, with sizes reaching up to 2 mu m and exhibiting varied morphologies, including irregular and cuboidal shapes. Additionally, this treatment led to the formation of some gamma '-gamma eutectic regions and plate-like eta phase, along with the decomposition of MC-type carbides into M23C6-type carbides. In contrast, the HT2 sample displayed uniformly distributed spherical primary gamma ' phase with sizes ranging from 70 to 120 nm, accompanied by very fine secondary gamma ' phase. Furthermore, it was found that changes in both aged sample microstructures could result in the formation of strain-age cracks due to the gamma ' phase formation and liquation cracks due to the partial remelting of lower melting point phases. The findings also revealed that with the application of aging treatments, the hardness of the as-fabricated sample (339.8 +/- 3.4 HV) increased to 440.2 +/- 5.6 HV and 508.1 +/- 4.8 HV for the heat treatment of HT1 and HT2, respectively.Article Influence of Microstructure and Crystallographic Texture on Hydrogen Diffusion in If-Steel(Technical Faculty, Bor-serbia, 2023) Baskaya, U.; Uzun, R.; Davut, K.; Kilic, Y.; Gunduz, O.The relation between microstructure, crystallographic texture, and hydrogen diffusion was studied on a IF-steel. The steel samples were deep drawn to a strain level of 10%, 20%, 30% and 40% and then the hydrogen diffusion coefficients were determined using the Helios II system. Light optical microscope (LOM), scanning electron microscope (SEM) and electron backscatter diffraction (EBSD) were used for microstructural characterization and crystallographic texture studies. The dependence of microstructural parameters was evaluated by Pearson correlation coefficient (PCC) values. These evaluations showed that local misorientations, crystallographic texture, and dislocation densityare interdependent. The PCC values show that grain size and dislocation density are the independent microstructure related parameters. These parameters were used to build a model to predict the hydrogen diffusion coefficient by multiple linear regression analysis. A sensitivity analysis was also performed with this model to understand to which parameter the hydrogen diffusion is most sensitive. The results of this analysis show that hydrogen diffusion is more sensitive to dislocation density, suggesting that dislocations are more effective trapping sites for hydrogen atoms. On the other hand, grain boundaries are less effective trapping sites since they also provide an additional diffusion mechanism.Article Citation - WoS: 11Citation - Scopus: 11A Comprehensive Characterization of the Effect of Spatter Powder on In939 Parts Fabricated by Laser Powder Bed Fusion(ELSEVIER SCI LTD, 2023) Dogu, Merve Nur; Mussatto, Andre; Yalçın, Mustafa Alp; Özer, Seren; Davut, Kemal; Obeidi, Muhannad Ahmed; Kumar, AjayThis study is focused on a comprehensive characterization of virgin and spatter IN939 powders and the effects of a certain amount of spatter powder on the part quality of IN939 fabricated by the L-PBF process. A brown tint coloration formed Al2O3 oxide, pores, a 124.4% increase in the average particle size, a 10.2% decrease in the powder circularity, and a 7.5% decrease in the powder aspect ratio were observed in the spatter powder. Additionally, higher average grain size and lower nanohardness were obtained for the spatter powder. In order to understand the effect of a certain amount of spatter powder on the part quality, 10 wt% spatter powder was mixed with the virgin powder. This addition was found to decrease the flowability of the powder. Moreover, this addition decreased relative density by around 0.3% and increased surface roughness by around 80.8% in the fabricated samples (termed as V and SV). On the other hand, there was no considerable microstructural, texture, microhardness, and nanohardness difference between V and SV samples, although the spatter powder addition caused a 30.2% increase in the average grain size of SV. The overall texture for both V and SV samples exhibit (00 1)//BD.Review Citation - WoS: 41Citation - Scopus: 42Review on the Parameters of Recycling Ndfeb Magnets Via a Hydrogenation Process(American Chemical Society, 2023) Habibzadeh, Alireza; Küçüker, Mehmet Ali; Gökelma, MertolRegarding the restrictions recently imposed by China on the export of rare-earth elements (REEs), the world may face a serious challenge in supplying some REEs such as neodymium and dysprosium soon. Recycling secondary sources is strongly recommended to mitigate the supply risk of REEs. Hydrogen processing of magnetic scrap (HPMS) as one of the best approaches for magnet-to-magnet recycling is thoroughly reviewed in this study in terms of parameters and properties. The processes of hydrogen decrepitation (HD) and hydrogenation-disproportio-nation-desorption-recombination (HDDR) are two common methods for HPMS. Employing a hydrogenation process can shorten the production route of new magnets from the discarded magnets compared to other recycling routes such as the hydrometallurgical route. However, determining the optimal pressure and temperature for the process is challenging due to the sensitivity to the initial chemical composition and the interaction of temperature and pressure. Pressure, temperature, initial chemical composition, gas flow rate, particle size distribution, grain size, and oxygen content are the effective parameters for the final magnetic properties. All these influencing parameters are discussed in detail in this review. The recovery rate of magnetic properties has been the concern of most research in this field and can be achieved up to 90% by employing a low hydrogenation temperature and pressure and using additives such as REE hydrides after hydrogenation and before sintering.Article Citation - WoS: 22Citation - Scopus: 25Effect of Solution Heat Treatment on the Microstructure and Crystallographic Texture of In939 Fabricated by Powder Bed Fusion-Laser Beam(Elsevier, 2023) Doğu, Merve Nur; Özer, Seren; Yalçın, Mustafa Alp; Davut, Kemal; Bilgin, Guney Mert; Obeidi, Muhannad Ahmed; Brodin, Hakan; Gu, Hengfeng; Brabazon, DermotThe effect of various solution heat treatment temperatures (i.e., 1120, 1160, 1200 and 1240 & DEG;C) on the microstructure, grain morphology and crystallographic texture of IN939 fabricated by powder bed fusion-laser beam (PBF-LB) was investigated. Microstructural analyses showed that the high-temperature gradient and rapid solidification of the PBF-LB processing caused different resulting microstructures compared to conventionally pro-duced counterparts. The melt pool morphologies and laser scanning paths were examined in the as-fabricated samples in the XZ-and XY-planes, respectively. After the application of solution heat treatment at 1120 & DEG;C, the as-fabricated PBF-LB initial microstructure was still apparent. For solution heat treatments of 1200 & DEG;C and above, the melt pool and scanning path morphologies disappeared and converted into a mixture of columnar grains in the XZ-plane and equiaxed grains in the XY-plane. On the other hand, large equiaxed grains were observed when the samples were solutionized at 1240 & DEG;C. Additionally, g' phase precipitated within the matrix after all solution heat treatment conditions, which led to increase in the microhardness values. According to electron backscatter diffraction (EBSD) analyses, both as-fabricated and solution heat-treated samples had intense texture with {001} plane normal parallel to the building direction. The first recrystallized grains began to appear when the samples were subjected to the solution heat treatment at 1160 & DEG;C and the fraction of the recrystallized grains increased with increasing temperature, as supported by kernel average misorientation (KAM) and grain spread orientation (GOS) analyses.& COPY; 2023 The Author(s). Published by Elsevier B.V. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).Article Citation - WoS: 5Citation - Scopus: 6Effect of Coiling Temperature on the Structure and Properties of Thermo-Mechanically Rolled S700mc Steel(Technical Faculty in Bor, 2022) Di Nunzio, P. E.; Cesile, M. C.; Oktay, S.; Davut, Kemal; Şeşen, M. K.The boron-free S700MC steel is usually produced by exploiting the properties of a ferrite-bainite mixed microstructure formed by coiling the strips at a temperature of about 450 degrees C, i.e.below the bainite starting temperature. With the aim of further enhancing the mechanical properties of 6 to 10 mm thick strips, industrial tests were carried out at a coiling temperature of 600 degrees C to promote the formation of a structure of ferrite and carbides, which is also acceptable for this type of steel. Unexpectedly, a microstructure composed of ferrite and martensite was obtained. Compared to the ferritic-bainitic grade, the new structure is characterized by a slight decrease of the yield point but by an increase of the ultimate tensile strength by no less than 80 MPa, with a transition from a quasi-discontinuous to a clearly continuous yielding behaviour. Accordingly, the ratio of yield strength to tensile strength decreases from 0.90 to 0.75 and the impact energy decreases by 35 J and 60 J for the two gauge levels, respectively. The mechanical behaviour of the strips coiled at high temperature is explained as a direct consequence of the dual phase structure with a hard phase interspersed in a soft ferrite matrix. The presence of martensite is explained by the so-called incomplete bainite reaction. The partial transformation into ferrite after coiling and the long time required for the coil to cool down stabilize the untransformed austenite due to the carbon enrichment making bainite formation at lower temperatures impossible.Article Citation - WoS: 3Citation - Scopus: 3Microstructural Characteristics of Mortars Prepared by Hot Lime Mix(Union of Croatian Civil Engineers and Technicians, 2020) Şerifaki, Kerem; Uğurlu Sağın, Elif; Böke, HasanThe effect of lime characteristics and hot lime mix method on hydraulic, microstructural and mechanical properties of mortars is determined by producing mortars from quicklimes of two different marbles and two limestones. Results of SEM-EDS, XRD and TGA analyses reveal that the porous microstructure of mortars and spongy texture of calcite crystals are the indicators of the hot lime mix method. This study shows that characteristics of limestones used for the production of limes, as well as the preparation method, directly affect hydraulic, mechanical and microstructural properties of mortars.Article Citation - WoS: 41Citation - Scopus: 45High Temperature Tensile, Compression and Creep Behavior of Recycled Short Carbon Fibre Reinforced Az91 Magnesium Alloy Fabricated by a High Shearing Dispersion Technique(National Engineering Research Center for Magnesium Alloys of China, Chongqing University, 2021) Kandemir, Sinan; Gavras, Sarkis; Dieringa, HajoThe present study seeks the feasibility of using short carbon fibres recycled from polymer matrix composites as alternative to virgin carbon fibres in the reinforcement of magnesium alloys. The microstructures, high temperature mechanical and creep properties of AZ91 alloy and its composites with various recycled carbon fibre contents (2.5 and 5 wt.%) and lengths (100 and 500 ?m) were investigated in the temperature range of 25–200 °C. The microstructural characterization showed that the high shear dispersion technique provided the cast composites with finer grains and relatively homogenous distribution of fibres. The materials tested displayed different behaviour depending on the type of loading. In general, while enhancements in the mechanical properties of composites is attributed to the load bearing and grain refinement effects of fibres, the fluctuations in the properties were discussed on the basis of porosity formation, relatively high reinforcement content leading to fibre clustering and interlayer found between the matrix and reinforcement compared to those of AZ91 alloy. The compressive creep tests revealed similar or higher minimum creep rates in the recycled carbon fibre reinforced AZ91 in comparison to the unreinforced AZ91. © 2021