Scopus İndeksli Yayınlar Koleksiyonu / Scopus Indexed Publications Collection
Permanent URI for this collectionhttps://hdl.handle.net/11147/7148
Browse
19 results
Search Results
Article Citation - WoS: 4Citation - Scopus: 4Optical and Photocatalytic Properties of Zno and Zns Structures Formed as Controlled Calcination Products of L-Cysteine Assisted Aqueous Precipitation(Elsevier, 2020) Şen, Selin; Top, AybenZnO and ZnS structures were obtained by the calcination of the aqueous precipitation products of Zn(NO3)2, NaOH and L-cysteine (Cys). Initial Cys:Zn molar ratios were changed as 0.1:1, 0.5:1, 1:1 and 1.5:1. All the precursors were transformed into ZnO upon calcination at 700 °C. ZnS structures were obtained by calcining the precursors prepared at the Cys:Zn ratios of 1 and 1.5 at 350 °C. In addition to changing chemical composition of the precipitation products, calcination temperature and initial Cys:Zn ratio also affected morphology, surface area, photoluminescence and photocatalytic properties of the final products. Free exciton energy values of the ZnO samples were observed to be between 3.29 eV and 3.35 eV. PL spectra of the ZnO samples indicated blue and green emission centers. Zinc interstitials (Zni), revealed by the blue emissions in the PL spectra were also confirmed by Auger Zn L3M4.5M4.5 spectra. The samples calcined at 350 °C removed rhodamine B mainly by adsorption. All the samples calcined at 700 °C successfully degraded the dye under UV light. Among the samples calcined at 700 °C, ZnO sample prepared at Cys:Zn = 0.5, which has the highest surface area and unique photoluminescence spectrum exhibited the fastest photodegradation rate. © 2020 Elsevier LtdArticle Citation - WoS: 10Citation - Scopus: 10The Comparison of Transient Photocurrent Spectroscopy Measurements of Pulsed Electron Deposited Zno Thin Film for Air and Vacuum Ambient Conditions(Elsevier, 2019) Özdoğan, Mehmet; Yiğen, Serap; Çelebi, Cem; Utlu, GökhanPhotoconduction mechanism of ZnO thin films that produced by Pulsed Electron Deposition method is systematically investigated by taking Transient Photocurrent Spectroscopy measurements for different atmospheres including high vacuum and air environments. Response and recovery rates of photocurrent in the air are faster than the rates in high vacuum condition. The results in the presented work clearly indicate that the photoconduction of ZnO thin films with high surface-area-to-volume ratio are surface-related and mostly governed by adsorption/desorption of oxygen and water molecules in the atmosphere. Therefore, the high surface interaction tendency of ZnO surface with the atmosphere inevitably leads to charge transfer from surface to adsorbates and/or vice versa.Article Citation - WoS: 31Citation - Scopus: 34Dual Remediation of Waste Waters From Methylene Blue and Chromium (vi) Using Thermally Induced Zno Nanofibers(Elsevier, 2020) Elhousseini, Mohamed Hilal; Isık, Tuğba; Kap, Özlem; Verpoort, Francis; Horzum, NesrinElectrospun zinc oxide (ZnO) nanofibers have been significantly improved via a simple heat treatment modification. The present work reports an intriguing cost-effective microstructure tuning, by drastically dropping the temperature of the calcined sample during the cooling period, to get highly photocatalytically active ZnO nanofibers. The calcination temperatures are deducted from thermogravimetric analysis, the phase and purity are confirmed by X-ray diffraction, while the morphology and texture have been revealed by field emission scanning electron microscopy and high-resolution transmission electron spectroscopy. X-ray photoelectron spectroscopy was conducted to get further insight on the surface composition and oxidation states, while N-2-adsorption isotherms were analyzed using the Brunauer-Emmet-Teller methodology. The crystallinity, surface area, and porosity of the ZnO nanofibers, as well as the exposure of active sites, have been enhanced by the rapid cooling method. Photodegradation activity toward methylene blue was improved from 88% to 94%, and 85% to 97%, for free cooled and rapid cooled samples calcined at 300 degrees C and 500 degrees C respectively. The adsorption of chromium (VI) was also tested and reached around 85 mg/g at 100 ppm without being saturated, thereby highlighting one of the most cost-effective performance-enhancing modifications so far that could be extended on different metal oxide nanomaterials.Article Citation - WoS: 22Citation - Scopus: 22Zinc Oxide and Metal Halide Perovskite Nanostructures Having Tunable Morphologies Grown by Nanosecond Laser Ablation for Light-Emitting Devices(American Chemical Society, 2020) Demirci Sankir, Nurdan; Abdullayeva, Nazrin; Altaf, Çiğdem Tuç; Kumtepe, Alihan; Yılmaz, Nazmi; Coşkun, Özlem; Sankir, Mehmet; Kurt, Hamza; Çelebi, Cem; Yanılmaz, AlperThis work reports a one-pot chemical bath deposition (CBD) method for the preparation of selectively grown, morphology-tunable zinc oxide (ZnO) nanostructures provided via straightforward nanosecond fiber laser ablation. Nanosecond fiber laser ablation is different from lithographic methods due to its simple, time saving, and efficient film scribing abilities. Here, multiple morphologies of the ZnO nanostructures on the same substrate have been grown via laser ablation of the ZnO seeding layer. Selective and controlled ablation of the titanium layer, ZnO growth inhibitor, resulted in systematic growth of nanorod arrays, while the application of extensive fluence energies resulted in the penetration of the laser beam until the glass substrate induced the nanoflake growth within the same CBD environment. The laser penetration depth has been numerically investigated via COMSOL Multiphysics heat module simulations, and the optical variations between two nanostructures (nanorod and nanoflake) have been examined via Lumerical FDTD. The simultaneous growth of two morphologies served as an efficient tool for the enhancement of photoluminescence intensities. It increased the average charge carrier lifetimes of the thin films from approximately 2.01 to 9.07 ns under the same excitation wavelengths. The amplification in PL performances has been accomplished via the capstone of all-inorganic halide perovskite (IHP) deposition that brought a successful conclusion to lifetime responses, which have been increased by 1.4-fold. The development of IHP sensitized nanoscaled multimorphological ZnO thin films can, therefore, be used as potential nanomaterials for light-emitting-device applications. © 2020 American Chemical Society.Article Citation - WoS: 15Citation - Scopus: 17Effect of Substrate Rotation Speed and Off-Center Deposition on the Structural, Optical, and Electrical Properties of Azo Thin Films Fabricated by Dc Magnetron Sputtering(American Institute of Physics, 2018) Türkoğlu, Fulya; Aygün, Gülnur; Köseoğlu, Hasan; Özdemir, Mehtap; Zeybek, S.; Özyüzer, Lütfi; Özdemir, Mehtap; Özyüzer, Gülnur Aygün; Özyüzer, LütfiIn this study, aluminum-doped zinc oxide (AZO) thin films were deposited by DC magnetron sputtering at room temperature. The distance between the substrate and target axis, and substrate rotation speed were varied to get high quality AZO thin films. The influences of these deposition parameters on the structural, optical, and electrical properties of the fabricated films were investigated by X-ray diffraction (XRD), Raman spectroscopy, spectrophotometry, and four-point probe techniques. The overall analysis revealed that both sample position and substrate rotation speed are effective in changing the optical, structural, and electrical properties of the AZO thin films. We further observed that stress in the films can be significantly reduced by off-center deposition and rotating the sample holder during the deposition. An average transmittance above 85% in the visible range and a resistivity of 2.02 × 10-3Ω cm were obtained for the AZO films.Article Citation - Scopus: 1Optical and Surface Properties of Zinc Oxide Nanoparticles Dried by Conventional and Supercritical Ethanol Drying Techniques(Research India Publications, 2014) Egbuchunam, Theresa Obuajulu; Yetgin, Senem; Özmıhçı Ömürlü, Filiz; Balköse, DevrimZinc oxide (ZnO) nanoparticles were synthesized by conventional (ZnO-A) and supercritical ethanol drying (ZnO-B). Nitrogen adsorption/desorption analyses were performed to determine the surface areas of the powders. The specific surface area was 28.30m2/g and 10.61 m2/g for ZnO-A and ZnO-B respectively. The powders adsorbed very small amount of CO2with the conventionally dried powder adsorbing more CO2. Supercritical ethanol dried ZnO had ethanol on its surface which was eliminated by vacuum application at room temperature. Both powders had OH groups which were eliminated on heating up to 500°C under vacuum. However, OH groups were present in lower amounts in supercritical ethanol dried ZnO. The powders were characterized by UV-VIS optical absorption and room temperature photoluminescence spectroscopic analyses. The UV-VIS absorption spectrum showed an absorption band at 375nm due to ZnO nanoparticles. The photoluminescence spectrum of ZnO excited at 380nm exhibited three emission peaks: one at 424nm and 490nm corresponding to band gap excitonic emission and another located at 520nm due to the presence of singly ionized oxygen vacancies.Article Citation - WoS: 6Citation - Scopus: 7Preparation and Characterization of Flexible Poly(vinyl Chloride) Foam Films(John Wiley and Sons Inc., 2012) Şahin, Erdem; Yaşar Mahlıçlı, Filiz; Yetgin, Senem; Balköse, DevrimIn this study, the effect of activator ZnO and heating time at 190°C on foaming, gelation, and dehydrochlorination of poly(vinyl chloride) (PVC) plastisol was investigated. For this purpose, a PVC plastisol was prepared by mixing PVC, dioctyl phthalate (DOP), azodicarbonamide (ADC), ZnO, and the heat stabilizers calcium stearate (CaSt 2) and zinc stearate(ZnSt 2). PVC plastisol films were heated for 3, 6, 12, and 24 min periods at 190°C to see the effect of heating time on the gelation and foaming processes of the PVC foam. The time of 12 min was determined to be optimum for the completion of gelation and foaming processes without thermal degradation of PVC. No foaming was observed under the same conditions for the samples without ZnO. ZnO had a significant catalytic effect on ADC decomposition, accelerating the foaming of the films. Average porosity measurement showed a consistent increase in porosity with heating time up to 76% and the average density decreased from 1.17 to 0.29 g/cm 3 on foaming. Tensile tests showed that the tensile strength and tensile strain both increased considerably up to 0.98 MPa and 207%, respectively, with heating time and the elastic modulus was seen to gradually decrease from 4.7 to 0.7 MPa with heating time. Films without ZnO had higher tensile strength since there were no pores. PVC thermomat tests showed that ZnO lowered the stability time of plastigel film with azodicarbonamide.Conference Object Citation - Scopus: 1Silver and Zinc Oxide Based Nano Powders and Their Polymer Based Nanocomposites for Antibacterial Application(European Conference on Composite Materials, 2014) Abatay, Ezgi; Özmen, Tuğçe; Arslanoğlu, Alper; Tanoğlu, MetinThe microorganisms cause some serious infections. It is a requirement and a necessity to create sterile fields such as hospital, food processing and public places. Composite stones are one of the main building materials that have been used in buildings due to their high resistant to abrasives, chemicals and mechanical impacts. The silver (Ag), zinc oxide (ZnO), and also nano Ag loaded ZnO (ZnO/Ag) nanopowders have demonsrated capability for the preparation of the polymer based antibacterial nanocomposite materials. In this study, Ag/polyester, ZnO/polyester, Ag/ZnO/polyester and their nanocomposites were prepared and tested with various weight fractions. The microstructure and surface morphology of these nanocomposites were investigated by means of scanning electron microscopy (SEM/EDX). The thermal properties were analyzed by differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA). Finally, The antibacterial properties of nanocomposites were analyzed against gram positive (Bacillus subtilis) and gram negative bacteria (Escherichia coli).Article Citation - WoS: 19Citation - Scopus: 20Isothermal Crystallization Kinetics and Mechanical Properties of Polycaprolactone Composites With Zinc Oxide, Oleic Acid, and Glycerol Monooleate(John Wiley and Sons Inc., 2013) Alp, Burcu; Cesur, SerapThe isothermal crystallization and mechanical behavior of polycaprolactone (PCL) with zinc oxide (ZnO) with oleic acid and glycerol monooleate (GMO) were studied. Theoretical melting points calculated by the Flory-Huggins and Thompson-Gibbs models were thoroughly compared with differential scanning calorimetry experimental observations. The isothermal crystallization kinetic parameters by Avrami analysis showed that crystallization was controlled by nucleation, crystal growth was spherical, and the nucleation type changed between thermal and athermal nucleation. X-ray diffraction showed that when the additives were used together both the crystal thickness and the degree of crystallinity increased. A multiple-response regression analysis was made with the ZnO, oleic acid, and GMO concentrations as variables and the crystallinity as output. Interaction parameters by the Pukanzky model were calculated from the tensile strength at the yield point and indicated that the addition of oleic acid or GMO improved the interface between the ZnO particles and PCL.Article Citation - WoS: 17Citation - Scopus: 21Effects of Particle Size and Electrical Resistivity of Filler on Mechanical, Electrical, and Thermal Properties of Linear Low Density Polyethylene-Zinc Oxide Composites(John Wiley and Sons Inc., 2013) Özmıhçı Ömürlü, Filiz; Balköse, DevrimThe effects of particle size and electrical resistivity of zinc oxide (ZnO) on mechanical properties, electrical and thermal conductivities of composites made with linear low density polyethylene (LLDPE) were investigated. Micron sized (mZnO), submicron sized (sZnO), and nano sized (nZnO) powders having resistivities of 1.5 × 106, 1.5 × 109, and 1.7 × 108 were used to prepare composites with 5-20 vol % filler. The tensile strength was lowered and the modulus of elasticity of the composites was increased with ZnO addition. Rather than the particle size of the ZnO, its initial resistivity and aspect ratio affected the resistivity of composites. The resistivity of the LLDPE was lowered from 2.3 × 1016 Ω cm down to 1.4 × 1010 Ω cm with mZnO addition. Thermal conductivity of the composites was increased with ZnO addition 2.5-3 times of the polymer matrix. The composites can be used for electrostatically dissipating and heat sink applications due to their decreased electrical resistivity and increased thermal conductivity.